LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2008 >> LS 460 >> Repair and Diagnosis >> Body & Frame >> Windows >> Windshield/WINDOWGLASS >> Power Window Control System >> Data List/Active Test
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Data List/Active Test

  1. DATA LIST 

    HINT:

    Using the Techstream to read the Data List allows values or status of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the DATA LIST information early in troubleshooting is one way to save diagnostic time.

    NOTE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / (desired system) / Data List /
    5. According to the display on Techstream, read the "Data List".

      Master Switch: 

      DATA LIST TABLE

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      D Door P/W Auto SW Driver side power window auto UP/DOWN switch signal / ON or OFF ON: Driver side power window auto UP/DOWN switch on master switch operated
      OFF: Driver side power window switch on master switch not operated      		 -
      P Door P/W Auto SW Front passenger side power window remote auto UP/DOWN switch signal / ON or OFF ON: Front passenger side power window remote auto UP/DOWN switch on master switch operated
      OFF: Front passenger side power window switch on master switch not operated      		 -
      RR Door P/W Auto SW Rear power window RH remote auto UP/DOWN switch signal / ON or OFF ON: Rear power window RH remote auto UP/DOWN switch on master switch operated
      OFF: Rear power window switch RH on master switch not operated      		 -
      RL Door P/W Auto SW Rear power window LH remote auto UP/DOWN switch signal / ON or OFF ON: Rear power window LH remote auto UP/DOWN switch on master switch operated
      OFF: Rear power window switch LH on master switch not operated      		 -
      P Door P/W Up SW Front passenger side power window remote manual UP switch signal / ON or OFF ON: Front passenger side power window remote manual UP switch on master switch operated
      OFF: Front passenger side power window switch on master switch not operated      		 -
      RR Door PAW up switch Rear power window RH remote manual UP switch signal / ON or OFF ON: Rear power window RH remote manual UP switch on master switch operated
      OFF: Rear power window switch RH on master switch not operated      		 -
      RL Door PAW up switch Rear power window LH remote manual UP switch signal / ON or OFF ON: Rear power window LH remote manual UP switch on master switch operated
      OFF: Rear power window switch LH on master switch not operated      		 -
      P Door P/W Down SW Front passenger side power window remote manual DOWN switch signal / ON or OFF ON: Front passenger side power window remote manual DOWN switch on master switch operated
      OFF: Front passenger side power window switch on master switch not operated      		 -
      RR Door P/W Down SW Rear power window RH remote manual DOWN switch signal / ON or OFF ON: Rear power window RH remote manual DOWN switch on master switch operated
      OFF: Rear power window switch RH on master switch not operated      		 -
      RL Door P/W Down SW Rear power window LH remote manual DOWN switch signal / ON or OFF ON: Rear power window LH remote manual DOWN switch on master switch operated
      OFF: Rear power window switch LH on master switch not operated      		 -
      Window Lock Switch Status Power window LOCK switch / ON or OFF ON: Power window lock switch LOCK position
      OFF: Power window lock switch UNLOCK position      		 -

      D-Door Motor: 

      DATA LIST TABLE

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      D Door P/W Auto SW Driver side power window auto UP/DOWN switch signal / ON or OFF ON: Driver side power window auto UP/DOWN switch on master switch operated
      OFF: Driver side power window switch on master switch not operated      		 -
      D Door P/W Up SW Driver side power window MANUAL UP switch signal/ON or OFF ON: Driver side power window manual UP switch on master switch operated
      OFF: Driver side power window switch on master switch not operated      		 -
      D Door P/W Down SW Driver side power window MANUAL DOWN switch signal/ ON or OFF ON: Driver side power window manual DOWN switch on master switch operated
      OFF: Driver side power window switch on master switch not operated      		 -
      Glass Position (Close-1/4) Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open position/OK or Caution OK: Margin is sufficient during manual UP operation
      CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.
      		 -
      Glass Position (1/4-2/4) Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open position/OK or Caution OK: Margin is sufficient during manual UP operation
      CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.
      		 -
      Glass Position (2/4-3/4) Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open position/OK or Caution OK: Margin is sufficient during manual UP operation
      CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.
      		 -
      Glass Position (3/4-Open) Margin for jam protection triggering force of window glass within range of 3/4 to fully open position/OK or Caution OK: Margin is sufficient during manual UP operation
      CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.
      		 -

      P-Door Motor: 

      DATA LIST TABLE

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      P Door P/W Auto SW Front passenger side power window auto UP/DOWN switch signal / ON or OFF ON: Front passenger side power window auto UP/DOWN switch operated
      OFF: Front passenger side power window switch not operated      		 -
      P Door P/W Up SW Front passenger side power window manual UP switch signal / ON or OFF ON: Front passenger side power window manual UP switch operated
      OFF: Front passenger side power window switch not operated      		 -
      P Door P/W Down SW Front passenger side power window manual DOWN switch signal / ON or OFF ON: Front passenger side power window manual DOWN switch operated
      OFF: Front passenger side power window switch not operated      		 -
      Glass Position (Close-1/4) Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open position/OK or Caution OK: Margin is sufficient during manual UP operation
      CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.
      		 -
      Glass Position (1/4-2/4) Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open position/OK or Caution OK: Margin is sufficient during manual UP operation
      CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.
      		 -
      Glass Position (2/4-3/4) Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open position/OK or Caution OK: Margin is sufficient during manual UP operation
      CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.
      		 -
      Glass Position (3/4-Open) Margin for jam protection triggering force of window glass within range of 3/4 to fully open position/OK or Caution OK: Margin is sufficient during manual UP operation
      CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.
      		 -

      RL-Door Motor: 

      DATA LIST TABLE

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      RL Door P/W Auto SW Rear power window LH auto UP/ DOWN switch signal / ON or OFF ON: Rear power window LH auto UP/DOWN switch operated
      OFF: Rear power window switch LH not operated      		 -
      RL Door P/W Up SW Rear power window LH manual UP switch signal / ON or OFF ON: Rear power window LH manual UP switch operated
      OFF: Rear power window switch LH not operated      		 -
      RL Door P/W Down SW Rear power window LH manual DOWN switch signal / ON or OFF ON: Rear power window LH manual DOWN switch operated
      OFF: Rear power window switch LH not operated      		 -
      Glass Position (Close-1/4) Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open position/OK or Caution OK: Margin is sufficient during manual UP operation
      CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.
      		 -
      Glass Position (1/4-2/4) Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open position/OK or Caution OK: Margin is sufficient during manual UP operation
      CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.
      		 -
      Glass Position (2/4-3/4) Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open position/OK or Caution OK: Margin is sufficient during manual UP operation
      CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.
      		 -
      Glass Position (3/4-Open) Margin for jam protection triggering force of window glass within range of 3/4 to fully open position/OK or Caution OK: Margin is sufficient during manual UP operation
      CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.
      		 -

      RR-Door Motor: 

      DATA LIST TABLE

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      RR Door P/W Auto SW Rear power window RH auto UP/ DOWN switch signal / ON or OFF ON: Rear power window RH auto UP/DOWN switch operated
      OFF: Rear power window switch RH not operated      		 -
      RR Door P/W Up SW Rear power window RH manual UP switch signal / ON or OFF ON: Rear power window RH remote manual UP switch operated
      OFF: Rear power window switch RH not operated      		 -
      RR Door P/W Down SW Rear power window RH manual DOWN switch signal / ON or OFF ON: Rear power window RH manual DOWN switch operated
      OFF: Rear power window switch RH not operated      		 -
      Glass Position (Close-1/4) Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open position/OK or Caution OK: Margin is sufficient during manual UP operation
      CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.
      		 -
      Glass Position (1/4-2/4) Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open position/OK or Caution OK: Margin is sufficient during manual UP operation
      CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.
      		 -
      Glass Position (2/4-3/4) Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open position/OK or Caution OK: Margin is sufficient during manual UP operation
      CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.
      		 -
      Glass Position (3/4-Open) Margin for jam protection triggering force of window glass within range of 3/4 to fully open position/OK or Caution OK: Margin is sufficient during manual UP operation
      CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.
      		 -

      Main Body: 

      DATA LIST TABLE

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Communication D-Door Motor Connection status between power window regulator motor (for driver side) and main body ECU/OK or Stop OK: Connection
      Stop: No connection      		 -
      Communication P-Door Motor Connection status between power window regulator motor (for front passenger side) and main body ECU/OK or Stop OK: Connection
      Stop: No connection      		 -
      Communication RR-Door Motor Connection status between power window regulator motor (for rear LH) and main body ECU/ OK or Stop OK: Connection
      Stop: No connection      		 -
      Communication RL-Door Motor Connection status between power window regulator motor (for rear RH) and main body ECU/OK or Stop OK: Connection
      Stop: No connection      		 -
      Communication Master SW Connection status between master switch and main body ECU/OK or Stop OK: Connection
      Stop: No connection      		 -
      D Door Courtesy SW Driver side door courtesy switch signal/ON or OFF ON: Driver door open
      OFF: Driver door closed      		 -
      P Door Courtesy SW Front passenger side door courtesy switch signal/ON or OFF ON: Front passenger door open
      OFF: Front passenger door closed      		 -
      RL Door Courtesy SW Rear LH side door courtesy switch signal / ON or OFF ON: Rear LH side door open
      OFF: Rear LH side door closed      		 -
      RR Door Courtesy SW Rear RH side door courtesy switch signal / ON or OFF ON: Rear RH side door open
      OFF: Rear RH side door closed      		 -
  2. ACTIVE TEST 

    HINT:

    Using the Techstream to perform Active Test allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Test early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Test.

    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / (desired system) / Active Test /
    5. According to the display on Techstream, perform the "Active Test".
      CAUTION: Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function does not operate.

      D-Door Motor: 

      ACTIVE TEST TABLE

      Tester Display Test Part Control Range
      Power Window Driver side power window UP/OFF
      Power Window Driver side power window DOWN/OFF

      P-Door Motor: 

      ACTIVE TEST TABLE

      Tester Display Test Part Control Range
      Power Window Front passenger side power window UP/OFF
      Power Window Front passenger side power window DOWN/OFF

      RL-Door Motor: 

      ACTIVE TEST TABLE

      Tester Display Test Part Control Range
      Power Window Rear LH side power window UP/OFF
      Power Window Rear LH side power window DOWN/OFF

      RR-Door Motor: 

      ACTIVE TEST TABLE

      Tester Display Test Part Control Range
      Power Window Rear RH side power window UP/OFF
      Power Window Rear RH side power window DOWN/OFF
scientia non olet · About LEMON Manuals