Customize Parameters

POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM

HINT:

The following can be customized.

NOTE:

Be sure to record the current value before customizing.
When troubleshooting, be careful as customizing could turn off the function. (Example: If the wireless operation does not function, check that it has not been turned off by customizing.)

TILT & TELESCO

TILT & TELESCO REFERENCE

DISPLAY (ITEM)	DEFAULT	CONTENTS	SETTING
AUTO TILT AWAY (Auto Away/Return Function)	ON	ON / Off of the auto away / return function.	ON/OFF

AIR CONDITIONING SYSTEM

HINT:

The followings are the possible items to be customized.

NOTE:

After confirming whether the items of the customer's request is applicable or not for the customized items, perform the customize operation.
Be sure to record the current value before customizing.
In case of performing the troubleshooting, pay attention as there is a possibility that the function is OFF by customizing. (Example: In case of the symptom in which "The wireless operation does not function", check that the wireless operation is not OFF by customizing, then perform the troubleshooting.)

AIR CONDITIONER:

AIR CONDITIONER REFERENCE TABLE

DISPLAY (ITEM)	DEFAULT	CONTENTS	SETTING
SET TEMP SHIFT (Set Temperature Shift)	NORMAL	To control with the shifted temperature against the display temperature.	+2C / +1C / NORMAL / -1C / -2C
AIR INLET MODE (Air Inlet Mode)	AUTO	In case of turning the A/C ON when you desire to make the compartment cool down quickly, this is the function to change the mode automatically to RECIRCULATED mode.	AUTO / MANUAL
COMPRESSOR MODE (Compressor Mode)	AUTO	Function to turn the A/C ON automatically by pressing the AUTO button when the blower is ON and the A/C is OFF.	AUTO / MANUAL
COMPRS/DEF OPER (Compressor/Air inlet DEF operation)	LINK	Function to turn the A/C ON automatically linking with the FRONT DEF button when the A/C OFF.	LINK / NORMAL
BUTTON PRS BUZ (Button press buzzer)	ON	Function to sound a buzzer when button is pressed.	OFF / ON
FOOT/DEF MODE (Foot/DEF auto mode)	ON	Function to turn the air flow from FOOT/DEF ON automatically when AUTO MODE is ON.	ON / OFF
AMBINT TMP SFT (Ambient Temperature Shift)	NORMAL	To control with the shifted ambient temperature against the display ambient temperature.	+3C / +2C / +1C / NORMAL / -1C / -2C / -3C

THEFT DETERRENT SYSTEM

HINT:

The following items can be customized.

NOTE:

After confirming whether the items requested by the customer are applicable or not for customization, perform customizing operations.
Be sure to record the current settings before customization.
When troubleshooting, make sure that the item in question is not set to "OFF" as a result of customization (Example: For the system, "the wireless function does not operate", first check that the wireless function is not set to "OFF", then perform troubleshooting).

THEFT DETERRENT SYSTEM:

THEFT DETERRENT SYSTEM REFERENCE

DISPLAY (ITEM)	DEFAULT	CONTENTS	SETTING
WARN BY HORN (Warning by horn)	ON	Function that makes vehicle horn and theft deterrent horn be able to be used as a warning device	ON/OFF
PASSIVE MODE (Passive Arming Mode)	OFF	PASSIVE MODE is a function that switches theft deterrent system from arming preparation state to armed state 30 seconds after key is removed from ignition key cylinder and driver side door is closed, even if doors are not locked by wireless or door key lock operation In PASSIVE MODE, if you do not perform following operations within 14 seconds after door is opened during armed state, theft deterrent system will judge that condition as a theft and switch to alarm sounding state Unlock any door by wireless operation Reconnect battery Insert key into ignition key cylinder and turn ignition switch from OFF to ON Unlock any door by key operation	ON/OFF
ENTRY DELAY (Entry delay time)	14 s	Function that changes entry delay time (time before warning starts) for PASSIVE MODE	0 s/14 s/30 s

LIGHTING SYSTEM

HINT:

The followings are the possible items to be customized.

NOTE:

After confirming whether the items of the customer's request is applicable or not for the customized items, perform the customize operation.
Be sure to record the current value before customizing.
In case of performing the troubleshooting, pay attention as there is a possibility that the function is OFF by customizing. (Example: In case of the symptom in which "The wireless operation does not function", check that the wireless operation is not OFF by customizing, then perform the troubleshooting.)

ILLUMINATED ENTRY

ILLUMINATED ENTRY REFERENCE TABLE

DISPLAY (ITEM)	DEFAULT	CONTENTS	SETTING
LIGHTING TIME (Lighting Time)	15 s	To change the lighting time after closing the door. (It will quickly fade out in case of turning the ignition ON.)	7.5 s/ 15 s/ 30 s
ILLUMI SYSTEM (Operation of illumination)	ON	Function to light up the step light, center console light and door inside handle light when one of the following occurs; the ignition turned ON, door unlock or door open.	ON/OFF
LIGHT CONTROL (Light control)	ON	Function to light up the step light and door inside handle light when the ignition switch is ON and the shift position is not P.	ON/OFF
I/L ON / UNLOCK (Interior light ON w/ door key unlock)	ON	Function to light up the interior light, ignition light and step light when unlocking with the door key cylinder. : Interior light comes on when the interior light switch is at the DOOR position.	ON / OFF
I/L ON / ACC OFF (Illumination system with ACC OFF)	ON	Function to light the interior light* and door courtesy light when the ignition switch is operated from "ACC" to "LOCK". *: interior light comes on when the interior light switch is at the DOOR position.	ON/OFF

LIGHT CONTROL

LIGHT CONTROL REFERENCE TABLE

DISPLAY (ITEM)	DEFAULT	CONTENTS	SETTING
LIGHT OFF DELAY (Light Auto OFF Delay)	30 s	Function to keep on lighting the headlight for a certain period of time after closing all the doors with the ignition switch turned OFF from ON under the condition that the light control switch is at HEAD or AUTO with the headlight ON.	OFF / 30 s / 60 s / 90 s
LIGHT CTRL TYPE (Control Type)	CURRENT	To change the control logic when the light control switch is AUTO position. Refer to ILLUSTRATION *1 REFERENCE TABLE .	CURRENT / OLD
SENSITIVITY (Turn ON luminous intensity)	NORMAL	To adjust the sensitivity of the lighting illumination. Refer to *2 illustration in Fig 1 .	DARK2 / DARK1 / NORMAL / LIGHT1 / LIGHT2
DISP EX ON SEN (Display Extinction Luminous Intensity)	NORMAL	To change the brightness of lowering the lights such as the indicator light of the combination meter, A/C indicator light, clock. Refer to *3 illustration in Fig 1 .	DARK2 / DARK1 / NORMAL / LIGHT1 / LIGHT2
DISP EX OFF SEN (Display Extinction Release Luminous Intensity)	NORMAL	To change the brightness of canceling the lowering the lights such as the indicator light of the combination meter, A/C indicator light, clock. Refer to *4 illustration in Fig 1 .	DARK2 / DARK1 / NORMAL / LIGHT1 / LIGHT2

HINT:

Sensitivity adjustment can hardly be confirmed. Please check by customer's actual driving.

Illustration *1

ILLUSTRATION *1 REFERENCE TABLE

Brightness of the surrounding when lighting

Lighting delay

Delay of turning light off

⁽²⁾

OLD

Old logic

6 sec.

3 sec.

CURRENT

New logic ⁽¹⁾ (97/8)

15 sec.

⁽¹⁾	The new one has the logic to light up two times brighter than the old logic.

⁽²⁾	Delay time until the headlight is turned on when it suddenly gets dark.

Fig 1: Identifying Light Control Display Table

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

WIPER AND WASHER SYSTEM

HINT:

The following items can be customized.

NOTE:

After confirming whether the items of the customer's request is applicable or not for the customized items, perform the customize operation.
Be sure to record the current value before customizing.
In case of performing the troubleshooting, pay attention as there is a possibility that the function is OFF by customizing. (Example: In case of the symptom in which "The wireless operation does not function", check that the wireless operation is not OFF by customizing, then perform the troubleshooting.)

WIPER

WIPER REFERENCE TABLE

Display (Item)	Default	Contents	Setting
SPEED MODE (Speed mode)	Avail	Function to change to the intermittent operation when the vehicle comes to stop (0 vehicle speed) from running condition in case that the wiper switch is at the LO position.	NOT AVAIL / AVAIL
AUTO WIPER (Auto wiper)	Avail	Function to operate the wiper automatically when it is raining	NOT AVAIL / AVAIL
REWIPE CONTROL (Rewipe control)	SPD MOD	Function to change time until operating the wiper to prevent dropping after having used the washer.	OFF / 3 s / SPD MOD

POWER DOOR LOCK CONTROL SYSTEM

CUSTOMIZING FUNCTION WITH INTELLIGENT TESTER (REFERENCE)

HINT:

The following items can be customized.

NOTE:

After confirming whether the items requested by the customer are applicable or not for customization, perform customize operations.
Be sure to record the current settings before customizing.
When troubleshooting, make sure that the item in question is not set to "OFF" as a result of customization.

BODY

BODY REFERENCE TABLE

Display (Item)	Default	Contents	Setting
AUTO LOCK DELAY	30s	Function that selects AUTO LOCK time 30 sec. or 60 sec.	30s/60s
AUTO LOCK (Auto Lock)	OFF	Function that locks doors when vehicle reaches a vehicle speed of 20 km/h (13 mph)	ON/OFF
UNLK/KEY TWICE (Unlock w/ 2 times D key operation)	ON	Function that unlocks only driver side door when driver side door key cylinder is turned to unlock once and unlocks all the doors when it is turned to unlock twice In OFF setting, turning it once unlocks all doors	ON/OFF
ALL UNLK/OPN-CL (All unlock w/ D door open-close)	OFF	Function that unlocks all other doors when opening driver side door within 10 seconds after turning the ignition switch off from ON	ON/OFF
UNLOCK/PARK (Unlock w/ IG ON, shift P, speed 0 (0 mph)	OFF	Function that unlocks doors when lever is shifted to P position from any position other than P while the ignition switch is ON	ON/OFF
AUTO LOCK/SHIFT (Auto Lock/shift not P)	ON	Function that locks doors when lever is shifted from P position to any position other than P	ON/OFF

WIRELESS DOOR LOCK CONTROL SYSTEM

HINT:

The following items can be customized.

NOTE:

When the customer requests a change in a function, first make sure that customization of the function(s) is possible.
Be sure to record the current settings before customizing.
When troubleshooting a function, first make sure that the function is not set to OFF.

WIRELESS DOOR LOCK CONTROL SYSTEM REFERENCE

Display (Item)	Default	Contents	Setting
OPEN DOOR WARN (Open door warning)	ON	If a door is not completely closed and LOCK is pressed, this function sounds a buzzer for 10 seconds.	ON / OFF
WIRLS BUZZ RESP (Buzzer answer-back of Wireless)	ON	This function makes the wireless door lock buzzer sound for answer-back when LOCK/ UNLOCK is pressed.	ON/OFF
WIRELESS OPER (Wireless door lock control function)	ON	This function turns the wireless door lock function on or off.	ON/OFF
ALARM FUNCTION (Panic function)	ON	This function operates the theft deterrent system when PANIC is pressed and held for 0.8 (1) or 2.5 (2) seconds.	ON/OFF
UNLOCK/2OPER (Wireless unlock operated twice)	ON	This function unlocks the driver side door when UNLOCK is pressed once, and unlocks all doors when pressed twice. If set to OFF, pressing UNLOCK once unlocks all doors.	ON/OFF
AUTO LOCK DELAY (Auto lock time)	30 s	This function controls the amount of time from unlocking doors to automatic re-locking.	30 S / 60 s
HAZARD ANS BACK (Hazards answer-back for wireless door lock operation)	ON	When LOCK is pressed, all hazard warning lights flash once. When UNLOCK is pressed, all hazard warning lights flash twice.	ON / OFF
HINT: (1): with Power Back Door (2): without Power Back Door

METER/GAUGE SYSTEM (Combination Meter Assembly)

NOTE: Be sure to record the current value before customizing.

HINT:

The following item can be customized without using the intelligent tester.

METER/GAUGE SYSTEM REFERENCE TABLE

Item	Default	Contents	Setting
Seat belt warning buzzer (See 9 procedure A)	b-on	Function to change the volume of the key reminder warning buzzer	b-on, b-oFF

METER/GAUGE SYSTEM (Seat Belt Buzzer ON/OFF Setting (Procedure "A"))
The seat belt buzzer ON/OFF setting, which is a setting of the buzzer function of the combination meter, can disable the driver and front passenger side seat belt buzzers.
NOTE:
- These buzzers should be on for safe driving. Perform these procedures only if it is necessary to set the buzzer off (disabled).
- When either the battery cable or the combination meter connector is disconnected, these buzzers are set on (enabled).
- Odometer returns to 0 after starting this procedure, although it is not displayed.
HINT:

"b-oFF" indicates that the buzzer is OFF. "b-on" indicates that the buzzer is ON. The seat belt buzzer ON/OFF setting will be finished (the odometer will display "ODO") if the ODO/TRIP switch is not operated for 10 seconds or more. In this case, perform step 11 to check that the buzzer ON/OFF setting is complete. If it is not complete, start from step 1 again.
1. Driver and front passenger side seat belt buzzers
  1. Turn the ignition switch to the ON position.
  2. Press the ODO/TRIP switch until the odometer displays "ODO".
  3. Turn the ignition switch off.
  4. Turn the ignition switch to the ON position.
  5. Press the ODO/TRIP switch immediately (within 6 seconds) and hold it down for 10 seconds or more.
  6. Continue holding down the ODO/TRIP switch and fasten the driver side seat belt.
  7. Check that the odometer displays either "b-on" or "b-oFF".
  8. Press the ODO/TRIP switch to change the display to "b-oFF".
  9. Turn the ignition switch off.
  10. Turn the ignition switch to the ON position. (11) Check that no buzzer sounds.
2. Front passenger side seat belt buzzer
  1. Turn the ignition switch to the ON position.
  2. Press the ODO/TRIP switch until the odometer displays "ODO".
  3. Turn the ignition switch off.
  4. Turn the ignition switch to the ON position.
  5. Sit in the front passenger seat. Press the ODO/ TRIP switch immediately (within 6 seconds) and hold it down for 10 seconds or more.
  6. Sit in the front passenger seat. Continue holding down the ODO/TRIP switch and fasten the front passenger side seat belt.
  7. Check that the odometer displays either "b-on" or "b-oFF".
  8. Press the ODO/TRIP switch to change the display to "b-oFF".
  9. Turn the ignition switch off.
  10. Turn the ignition switch to the ON position.
  11. Check that no buzzer sounds.

POWER WINDOW CONTROL SYSTEM

HINT:

The following items can be customized.

NOTE:

After confirming whether the items requested by the customer are applicable or not for customization, perform customize operations.
Be sure to record the current settings before customizing.
When troubleshooting, make sure that the item in question is not set to "OFF" as a result of customization. (Example: For the symptom "the wireless function does not operate", first check that the wireless function is not set to "OFF", then perform troubleshooting).

POWER WINDOW

POWER WINDOW REFERENCE TABLE

DISPLAY (ITEM)	DEFAULT CONTENTS	CONTENTS	SETTING
UP/DOOR KEY (Door key linked P/W UP)	AVIL	Function that enables all power windows to move up manually, via manual operation, when driver side door key cylinder is held in lock position for 1.5 seconds when ignition switch is off.	NOT/AVIL
DOWN/DOOR KEY (Door key linked P/W DOWN)	AVIL	Function that enables all power windows to move down manually, via manual operation, when driver side door key cylinder is held in unlock position for 1.5 seconds when ignition switch is off.	NOT/AVIL
DOWN/WIRELESS (P/W DOWN w/ transmitter)	AVIL	Function that enables all power windows to move down manually, via manual operation, when unlock switch on transmitter is held for 1.5 seconds when ignition switch is off.	NOT/AVIL
UP/WIRELESS (P/W UP w/ transmitter)	AVIL	Function that enables all power windows to move up manually, via manual operation, when lock switch on transmitter is held for 1.5 seconds when ignition switch is off.	NOT/AVIL

POWER BACK DOOR SYSTEM

HINT:

The following items can be customized.

NOTE:

After confirming whether the items requested by the customer are applicable or not for customization, perform customize operations.
Be sure to record the current settings before customizing.
When troubleshooting, make sure that the item in question is not set to "OFF" as a result of customization.

Power back door ECU

POWER BACK DOOR ECU REFERENCE TABLE

DISPLAY (ITEM)	DEFAULT	CONTENTS	SETTING
PBD SW OPER	0.8s	Function that turns power back door closer switch ON when switch is pushed once or held down for 0.8 sec.	0.8s/ON
PBD BUZZ VOL	LARGE	Function that adjusts the volume of warning buzzer that notifies power back door is operating	OFF/SMALL/LARGE
PBD ONE MOTION	OFF	Function to operate PBD by transmitter (0.8 sec. press) when back door is locked.	ON/OFF
WIRELS PBD OPER	0.8s	Function that operates power back door when transmitter switch is pressed in specified way (1-press, 2-presses, 0.8 sec-press or OFF*1)	ON/TWICE ON/0.8s/OFF
PBD ASSIST OPN*2	OFF	Function that helps power back door opening operation	ON/OFF
HINT: 1: Wireless (transmitter switch) operation of the power back door is disabled. 2: When this item is set to ON: When the back door is fully closed, pulling the back door opener switch (outside handle switch) activates the power back door system to automatically open the back door after that it is unlatched.