LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2008 >> SC 430 >> Repair and Diagnosis >> Body & Frame >> Windows >> Windshield/WINDOWGLASS >> Power Window Control System >> Data List / Active Test
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Data List / Active Test

  1. READ DATA LIST 

    HINT:

    Using the Techstream to read the Data List allows the value or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent condition or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    NOTE: In the table below, the values liste under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not. 
    1. Turn the ignition switch LOCK.
    2. Connect the Techstream to the DLC3.
    3. Turn the ignition switch ON.
    4. Turn the Techstream on.
    5. Enter the following menus: Body Electrical / (desired system) / Data List
    6. According to the display on the Techstream, read the "Data List"

      Driver Door 

      DATA LIST - DRIVER DOOR

      Tester Display Measurement Item / Range Normal Condition Diagnostic Note
      Door P/W Auto SW Driver side power window auto UP/DOWN switch signal / ON or OFF ON: Driver side power window auto UP/DOWN switch on master switch operated
      OFF: Driver side power window switch on master switch not operated      		 -
      P Door P/W Auto SW Front passenger side power window remote auto UP/DOWN switch signal / ON or OFF ON: Front passenger side power window auto UP/DOWN switch on master switch operated
      OFF: Front passenger side power window switch on master switch not operated      		 -
      Jam Protection Limit SW Jam protection limit switch signal / ON or OFF ON: Jam protection limit switch operated
      OFF: Jam protection limit switch does not operate      		 -
      Glass Position (Close-1/4) Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open position / OK or CAUTION OK: Margin is sufficient during manual UP operation
      CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.      		 -
      Glass Position (1/4-2/4) Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open position / OK or CAUTION OK: Margin is sufficient during manual UP operation
      CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.      		 -
      Glass Position (2/4-3/4) Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open position / OK or CAUTION OK: Margin is sufficient during manual UP operation
      CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.      		 -
      Glass Position (3/4-Open) Margin for jam protection triggering force of window glass within range of 3/4 to to fully open position / OK or CAUTION OK: Margin is sufficient during manual UP operation
      CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.      		 -

      Passenger Door 

      DATA LIST - PASSENGER DOOR

      Tester Display Measurement Item / Range Normal Condition Diagnostic Note
      Door P/W Auto SW Passenger side power window AUTO operation ON / OFF OK: Passenger door power window AUTO switch operates
      OGG: Passenger door power window AUTO switch does not operate      		 -
      Jam Protection Limit SW Jam protection limit switch ON / OFF ON: Jam protection limit switch operates
      OFF: Jam protection limit switch does not operate      		 -
      Glass Position (Close-1/4) Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open position / OK or CAUTION OK: Margin is sufficient during manual UP operation
      CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position
      		 -
      Glass Position (1/4-2/4) Margin for jam protection triggering force of window glass within range of fully 1/4 to 1/2 open position / OK or CAUTION OK: Margin is sufficient during manual UP operation
      CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position
      		 -
      Glass Position (2/4-3/4) Margin for jam protection triggering force of window glass within range of fully 1/2 to 3/4 open position / OK or CAUTION OK: Margin is sufficient during manual UP operation
      CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position
      		 -
      Glass Position (3/4-Open) Margin for jam protection triggering force of window glass within range of fully 3/4 to fully open position / OK or CAUTIO OK: Margin is sufficient during manual UP operation
      CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position
      		 -
  2. PERFORM ACTIVE TEST 
    NOTE: When a Rear Junction Block ECU and Multiplex Network Front Light ECU (Front Controller) related vehicle switch is ON, Active Test items related to the vehicle switch are prohibited (double operation prohibition). Check that the vehicle switches are OFF before performing Active Tests. 

    HINT:

    Using the Techstream to perform Active Test allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Test early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Test.

    1. Turn the ignition switch LOCK.
    2. Connect the Techstream to the DLC3.
    3. Turn the ignition switch ON.
    4. Turn the Techstream on.
    5. Enter the following menus: Body Electrical / Back Door / Active Test.
    6. According to the display on the Techstrea, perform the "Active Test".

      Driver Door 

      ACTIVE TEST - DRIVER DOOR

      Tester Display Test Part Diagnostic Note Diagnostic Note
      Power Window Driver side power window UP/OFF (OFF) -
      DOWN/OFF (OFF) -

      Passenger Door 

      ACTIVE TEST - PASSENGER DOOR

      Tester Display Test Part Control Range Diagnostic Note
      Power Window front passenger side power window UP/OFF (OFF) -
      DOWN/OFF (OFF) -
scientia non olet · About LEMON Manuals