| Camshaft timing oil control valve |
Engine speed while operating the Oil Control Valve (OCV) |
Tester Operation |
Specified Condition |
| 0 % |
Normal engine speed |
| 30 % |
Engine idles roughly |
| Standard resistance |
Tester Connection |
Condition |
Specified Condition |
| 1 - 2 |
20°C (68°F) |
6.9 to 7.9 Ω |
| Throttle body |
Standard resistance |
Tester Connection |
Condition |
Specified Condition |
| 1 (M-) - 2 (M+) |
20°C (68°F) |
0.3 to 100 Ω |
| 3 (E2) - 5 (VC) |
20°C (68°F) |
2.0 to 4.0 kΩ |
| Mass air flow meter |
Standard resistance |
Tester Connection |
Condition |
Specified Condition |
| 5 (THA) - 4 (E2) |
-20°C (-4°F) |
13.6 to 18.4 kΩ |
| 20°C (68°F) |
2.21 to 2.69 kΩ |
| 60°C (140°F) |
0.49 to 0.67 kΩ |
| Engine coolant temperature sensor |
Standard resistance |
Tester Connection |
Condition |
Specified Condition |
| 1 - 2 |
Approximately 20°C (68°F) |
2.32 to 2.59 kΩ |
| 1 - 2 |
Approximately 80°C (176°F) |
0.310 to 0.326 kΩ |
| Knock sensor |
Standard resistance |
Tester Connection |
Condition |
Specified Condition |
| 1 - 2 |
20°C (68°F) |
120 to 280 kΩ |
| Air fuel ratio sensor (for Bank 1 Sensor 1) |
Standard resistance |
Tester Connection |
Condition |
Specified Condition |
| for 2WD |
1 (HT) - 2 (+B) |
20°C (68°F) |
1.8 to 3.4 Ω |
| for AWD |
1 (HA1A) - 2 (+B) |
20°C (68°F) |
1.8 to 3.4 Ω |
| Air fuel ratio sensor (for Bank 2 Sensor 1) |
Standard resistance |
Tester Connection |
Condition |
Specified Condition |
| for 2WD |
1 (HT) - 2 (+B) |
20°C (68°F) |
1.8 to 3.4 Ω |
| for AWD |
1 (HA2A) - 2 (+B) |
20°C (68°F) |
1.8 to 3.4 Ω |
| Heated oxygen sensor (for Bank 1 Sensor 2) |
Standard resistance |
Tester Connection |
Condition |
Specified Condition |
| for 2WD |
1 (HT) - 2 (+B) |
20°C (68°F) |
11 to 16 Ω |
| for AWD |
1 (HT1B) - 2 (+B) |
20°C (68°F) |
11 to 16 Ω |
| Heated oxygen sensor (for Bank 2 Sensor 2) |
Standard resistance |
Tester Connection |
Condition |
Specified Condition |
| for 2WD |
1 (HT) - 2 (+B) |
20°C (68°F) |
11 to 16 Ω |
| for AWD |
1 (HT2B) - 2 (+B) |
20°C (68°F) |
11 to 16 Ω |
| VVT relay (VVT RH, VVT LH) |
Standard resistance |
Tester Connection |
Condition |
Specified Condition |
| 3 - 5 |
When no battery voltage is applied to terminals 1 and 2 |
10 kΩ or higher |
| 3 - 5 |
When battery voltage is applied to terminals 1 and 2 |
Below 1 Ω |
| Ignition relay No. 1 (IG1) |
Standard resistance |
Tester Connection |
Condition |
Specified Condition |
| 3 - 5 |
When no battery voltage is applied to terminals 1 and 2 |
10 kΩ or higher |
| 3 - 5 |
When battery voltage is applied to terminals 1 and 2 |
Below 1 Ω |
| Ignition relay No. 2 (IG2) |
Standard resistance |
Tester Connection |
Condition |
Specified Condition |
| 3 - 5 |
When no battery voltage is applied to terminals 1 and 2 |
10 kΩ or higher |
| 3 - 5 |
When battery voltage is applied to terminals 1 and 2 |
Below 1 Ω |
| EFI relay (EFI MAIN, EFI MAIN2) |
Standard resistance |
Tester Connection |
Condition |
Specified Condition |
| 3 - 5 |
When no battery voltage is applied to terminals 1 and 2 |
10 kΩ or higher |
| 3 - 5 |
When battery voltage is applied to terminals 1 and 2 |
Below 1 Ω |
| Circuit opening relay (C/OPN) |
Standard resistance |
Tester Connection |
Condition |
Specified Condition |
| 3 - 5 |
When no battery voltage is applied to terminals 1 and 2 |
10 kΩ or higher |
| 3 - 5 |
When battery voltage is applied to terminals 1 and 2 |
Below 1 Ω |
| Fuel pump relay (F/PMP) |
Standard resistance |
Tester Connection |
Condition |
Specified Condition |
| 3 - 4 |
When no battery voltage is applied to terminals 1 and 2 |
Below 1 Ω |
| 3 - 4 |
When battery voltage is applied to terminals 1 and 2 |
10 kΩ or higher |
| Camshaft timing control motor |
Joint width |
Standard |
5.90 to 5.95 mm (0.232 to 0.234 in.) |
| Keyway part width |
Standard |
6.02 to 6.11 mm (0.237 to 0.241 in.) |
| Joint clearance |
standard |
0.07 to 0.21 mm (0.00276 to 0.00827 in.) |
| Maximum |
0.7 mm (0.0276 in.) or more |