LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lincoln >> 2000 >> Navigator 4WD >> Repair and Diagnosis >> Body & Frame >> Door Locks >> Remote Keyless Entry Systems >> System Tests >> Test C: Memory Seat Does Not Operate With Transmitter
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Test C: Memory Seat Does Not Operate With Transmitter

  1. Turn ignition off. Press any button on remote transmitter. Connect NGS tester following manufacturer's instructions. Select TRANSMITTER TIC/DATA from RAP FUNCTION test list. Compare LAST TIC RECEIVED with data stored in TIC1, TIC2, TIC3 and TIC4 to determine which transmitter is being used. Repeat procedure with second transmitter. If transmitters one and two are identified, go to next step. If transmitters one and two cannot be identified, go to TEST A: DOORS DO NOT LOCK OR UNLOCK WITH REMOTE TRANSMITTER  .
  2. Adjust driver's seat, exterior mirrors and adjustable pedals to a new position and store to MEMORY 1. Move seat, mirror and pedals to different positions. Press UNLOCK button on transmitter No. 1. If memory seat moves to position No. 1, go to next step. If seat does not move to position No. 1, go to step  7 .
  3. Adjust driver's seat, exterior mirrors and adjustable pedals to a new position and store to MEMORY 2. Move seat, mirror and pedals to different positions. Press UNLOCK button on transmitter No. 2. If memory seat moves to position No. 2, system is operating properly. If seat does not move to position No. 2, go to next step.
  4. Ensure MEMORY 1 is off. Using NGS tester, select MEM SELECT CTRL from RAP active command list and turn MEMORY 2 to ON. If memory seat moves to position No. 2, replace RAP module. Recheck system operation. If seat does not move to position No. 2, go to next step.
  5. Using NGS tester, turn MEMORY 2 to OFF. Disconnect driver seat module (DSM) 22-pin connector C356. Disconnect RAP module 22-pin connector C257. Measure resistance of Black/Orange wire between RAP module connector C257 terminal No. 18 and DSM module connector C356 terminal No. 15. If resistance is less than 5 ohms, reconnect RAP module connector. Go to next step. If resistance is less than 5 ohms, repair open in Black/Orange wire. Recheck system operation.
  6. Turn MEMORY 2 to ON. Measure voltage between ground and DSM module 22-pin connector terminal No. 15 (Black/Orange wire). If more than 10 volts exists, replace DSM. Recheck system operation. If 10 volts or less exists, replace RAP module. Recheck system operation.
  7. Using NGS tester and Service Function Card, select ANTI-THEFT CONFIGURE from RAP menu. If PERSONALITY feature is enabled, go to next step. If PERSONALITY feature is not enabled, replace RAP module. Recheck system operation.
  8. Ensure MEMORY 1 is OFF. Using NGS tester, select MEM SELECT CTRL from RAP active command list and turn MEMORY 1 to ON. If memory seat moves to No. 1 position, replace RAP module. Recheck system operation. If memory seat does not move to position No. 1, go to next step.
  9. Using NGS tester, turn MEMORY 1 to OFF. Disconnect 22-pin driver seat module (DSM) connector C356. Disconnect RAP module 22-pin connector C257. Measure resistance of Brown/Light Green wire between RAP module 22-pin connector terminal No. 6 and DSM module 22-pin connector terminal No. 16. If resistance is less than 5 ohms, reconnect RAP module connector. Go to next step. If resistance is less than 5 ohms, repair open in Brown/Light Green wire. Recheck system operation.
  10. Using NGS tester, turn MEMORY 1 to ON. Measure voltage between ground and DSM module 22-pin connector terminal No. 16 (Brown/Light Green wire). If more than 10 volts exists, replace DSM. Recheck system operation. If 10 volts or less exists, replace RAP module. Recheck system operation.
scientia non olet · About LEMON Manuals