Anti-Lock Control DTCS
ANTI-LOCK CONTROL DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Source | Perform Test |
|---|---|---|---|
| B1342 | ECU Is Defective | ABS |
NOTE:
If other DTCs are present, REPAIR them before installing a new component. CLEAR the DTCs. RETRIEVE the DTCs. If DTC B1342 is still present, INSTALL a new module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE
. REPEAT the self-test.
|
| B1483 | Brake Pedal Input Circuit Failure | ABS | GO to PINPOINT TEST B . |
| B1676 | Battery Pack Voltage Out of Range | ABS | GO to PINPOINT TEST C . |
| B2477 | Module Configuration Failure | ABS | Follow the diagnostic tool directions for the calibration procedure. |
| B2734 | Pedal Travel Sensor (PTS) Supply Error | ABS | Follow the diagnostic tool directions for the calibration procedure. |
| B2736 | Pedal Travel Sensor (PTS) Circuit Fault | ABS | Follow the diagnostic tool directions for the calibration procedure. |
| B2737 | Pedal Travel Sensor (PTS) Jammed Error | ABS | Follow the diagnostic tool directions for the calibration procedure. |
| B2738 | Pedal Travel Sensor (PTS) Velocity Error | ABS | Follow the diagnostic tool directions for the calibration procedure. |
| B2740 | Pedal Travel Sensor (PTS) Spike Error | ABS | Follow the diagnostic tool directions for the calibration procedure. |
| B2741 | Sensor Cluster Loop End | ABS | Follow the diagnostic tool directions for the calibration procedure. |
| B2900 | VIN Mismatched | ABS | VERIFY that the ABS module has the correct as-built data. |
| C1095 | ABS Hydraulic Pump Motor Circuit Failure | ABS | GO to PINPOINT TEST D . |
| C1145 | Wheel Speed Sensor RF Input Circuit Failure | ABS | GO to PINPOINT TEST E . |
| C1155 | Wheel Speed Sensor LF Input Circuit Failure | ABS | GO to PINPOINT TEST E . |
| C1165 | Wheel Speed Sensor RR Input Circuit Failure | ABS | GO to PINPOINT TEST E . |
| C1175 | Wheel Speed Sensor LR Input Circuit Failure | ABS | GO to PINPOINT TEST E . |
| C1233 | Wheel Speed LF Input Signal Missing | ABS | GO to PINPOINT TEST F . |
| C1234 | Wheel Speed RF Input Signal Missing | ABS | GO to PINPOINT TEST F . |
| C1235 | Wheel Speed RR Input Signal Missing | ABS | GO to PINPOINT TEST F . |
| C1236 | Wheel Speed LR Input Signal Missing | ABS | GO to PINPOINT TEST F . |
| C1277 | Steering Wheel Angle 1 and 2 Circuit Failure | ABS | GO to PINPOINT TEST G . |
| C1278 | Steering Wheel Angle 1 and 2 Signal Faulted | ABS | GO to PINPOINT TEST G . |
| C1279 | Yaw Rate Sensor Circuit Failure | ABS | GO to PINPOINT TEST H . |
| C1280 | Yaw Rate Sensor Signal Fault | ABS | GO to PINPOINT TEST H . |
| C1281 | Lateral Accelerometer Circuit Failure | ABS | GO to PINPOINT TEST H . |
| C1282 | Lateral Accelerometer Signal Fault | ABS | GO to PINPOINT TEST H . |
| C1285 | Booster Solenoid Circuit Failure | ABS | GO to PINPOINT TEST I . |
| C1287 | Booster Pedal Force Switch Circuit Failure | ABS | GO to PINPOINT TEST J . |
| C1288 | Brake Pressure Transducer Input Circuit Failure | ABS | GO to PINPOINT TEST K . |
| C1440 | Pressure Transducer Input Circuit Failure | ABS | GO to PINPOINT TEST P . |
| C1730 | Reference Voltage Out of Range (+5 V) | ABS | GO to PINPOINT TEST L . |
| C1805 | Mismatched PCM and/or ABS Module | ABS | CHECK for correct component and correct PCM and ABS module configuration. INSTALL a new component as necessary. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE . CLEAR the DTC. REPEAT the self-test. |
| C1963 | Stability Control Inhibit Warning | ABS | This DTC is for information only. GO to the PRINCIPLES OF OPERATION . CLEAR the DTC. REPEAT the self-test. |
| C1969 | Traction Control/Yaw Control Switch Lamp Circuit Fault | ABS | GO to PINPOINT TEST Q . |
| C1991 | Module Calibration Failure | ABS | CALIBRATE the Traction Control Module. REFER to MODULE COMMUNICATIONS NETWORK . |
| C1996 | Active Yaw Control Disabled | ABS | This DTC can be set if the Advance Trac®/IVD System is activated for 15 seconds of continuous operation. CHECK for any major chassis modifications, gross suspension misalignment or other items that can alter the vehicle tracking dynamics. |
| C1998 | Module Calibration Not Complete | ABS | GO to PINPOINT TEST R . |
| C2769 | Longitudinal Acceleration Sensor Circuit Failure | ABS | GO to PINPOINT TEST H . |
| C2770 | Longitudinal Acceleration Sensor Signal Fault | ABS | GO to PINPOINT TEST H . |
| C2777 | Sensor Cluster Bus Failure | ABS | GO to PINPOINT TEST S . |
| C2778 | Sensor Power Supply Failure | ABS | GO to PINPOINT TEST S . |
| U1009 | SCP (J1850) Invalid or Missing Data for Engine Torque | PCM | See INTRODUCTION - GASOLINE article . |
| U1027 | SCP (J1850) Invalid or Missing Data for Engine RPM | PCM | See INTRODUCTION - GASOLINE article . |
| U1059 | SCP (J1850) Invalid or Missing Data for Transmission/Transaxle/PRNDL | PCM | See INTRODUCTION - GASOLINE article . |
| U1073 | SCP (J1850) Invalid or Missing Data for Engine Coolant | PCM | See INTRODUCTION - GASOLINE article . |
| U1262 | SCP (J1850) Communication Bus Fault | Network Fault | REFER to MODULE COMMUNICATIONS NETWORK . |
| U1900 | CAN Network 1 Communication Bus Fault-Receive Error | Network Fault | REFER to MODULE COMMUNICATIONS NETWORK . |
| U1901 | CAN Network 2 Communication Bus Fault-Receive Error | Network Fault | REFER to MODULE COMMUNICATIONS NETWORK . |
POWERTRAIN CONTROL MODULE (PCM) DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Source | Perform Test |
|---|---|---|---|
| P2106 | Throttle Actuator Control System -- Forced Limit Power | PCM | Repair all other ABS module DTCs first. If the DTC is still present, See INTRODUCTION - GASOLINE article . |