Information System And Entertainment System DTCS
AUDIO FRONT CONTROL MODULE (ACM) DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Action |
|---|---|---|
| B119F:01 | GPS Antenna: General Electrical Failure | GO to Pinpoint Test S . |
| B119F:13 | GPS Antenna: Circuit Open | GO to Pinpoint Test S . |
| B11BA:1C | Steering Wheel Audio Switch Pack: Circuit Voltage Out of Range | GO to Pinpoint Test M . |
| B11BA:63 | Steering Wheel Audio Switch Pack: Circuit / Component Protection Time-Out | GO to Pinpoint Test M . |
| B1201:1C | Steering Wheel Audio Switch Pack 2: Circuit Voltage Out of Range | GO to Pinpoint Test M . |
| B1201:63 | Steering Wheel Audio Switch Pack 2: Circuit / Component Protection Time-Out | GO to Pinpoint Test M . |
| B121C:01 | Hard Drive: General Electrical Failure | CLEAR the DTCs. REPEAT the self-test. If DTC B121C:01 is retrieved again, INSTALL a new Audio Front Control Module (ACM). REFER to Audio Control Module (ACM) . REPEAT the self-test. |
| B1A01:01 | Speaker #1: General Electrical Failure | GO to Pinpoint Test C . |
| B1A02:01 | Speaker #2: General Electrical Failure | GO to Pinpoint Test C . |
| B1A03:01 | Speaker #3: General Electrical Failure | GO to Pinpoint Test C . |
| B1A04:01 | Speaker #4: General Electrical Failure | GO to Pinpoint Test C . |
| B1A05:01 | Speaker #5: General Electrical Failure | GO to Pinpoint Test C . |
| B1A06:01 | Speaker #6: General Electrical Failure | GO to Pinpoint Test C . |
| B1A56:21 | Antenna: Signal Amplitude Minimum |
NOTE:
If DTC B1A56:21 sets after running the bezel diagnostic tests disregard this DTC. This test is used for end of line or repair bay testing at the Ford plant. Each plant has its own assigned frequency and signal strength requirements. The running and passing of this test depends on local radio stations. If no local station is broadcasting on the required frequency the test will fail. Therefore test ran from the bezel diagnostic screen and the DTC generated from the test can be disregarded. DISREGARD this DTC. |
| B1A89:01 | Satellite Antenna: General Electrical Failure | GO to PINPOINT TEST R . |
| B1A89:13 | Satellite Antenna: Circuit Open | GO to PINPOINT TEST R . |
| B1D19:49 | Compact Disc Unit: Internal Electronic Failure | CLEAR the DTCs. REPEAT the self-test. If DTC B1D19:49 is retrieved again, INSTALL a new ACM. REFER to Audio Control Module (ACM) . REPEAT the self-test. |
| B1D19:4B | Compact Disc Unit: Over Temperature | The ACM was over-temperature. This can occur during extended use. Audio operation can resume after the ACM cools. CLEAR the DTCs. This is normal operation. |
| B1D79:01 | Microphone Input: General Electrical Failure | GO to Pinpoint Test P . |
| C1001:01 | Vision System Camera: General Electrical Failure | Refer to PARKING AID . |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test AB . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test AO . |
| U0162:00 | Lost Communication With Navigation Display Module: No Sub Type Information | GO to Pinpoint Test J . |
| U0164:00 | Lost Communication With HVAC Control Module: No Sub Type Information | GO to Pinpoint Test AP . |
| U0197:00 | Lost Communication With Telephone Control Module: No Sub Type Information | GO to Pinpoint Test AR . |
| U0238:00 | Lost Communication With Digital Audio Control Module "D": No Sub Type Information | GO to Pinpoint Test AS . |
| U2014:41 | Control Module Hardware: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:41 is retrieved again, INSTALL a new ACM. REFER to Audio Control Module (ACM) . REPEAT the self-test. |
| U2014:42 | Control Module Hardware: General Memory Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:42 is retrieved again, INSTALL a new ACM. REFER to Audio Control Module (ACM) . REPEAT the self-test. |
| U2014:96 | Control Module Hardware: Component Internal Failure | GO to Pinpoint Test Q . |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | Refer to MODULE CONFIGURATION . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | Refer to MODULE CONFIGURATION . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | Refer to MODULE CONFIGURATION . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AC . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AD . |
AUDIO DIGITAL SIGNAL PROCESSING (DSP) MODULE DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Action |
|---|---|---|
| B1A01:11 | Speaker #1: Circuit Short to Ground | GO to Pinpoint Test C . |
| B1A01:12 | Speaker #1: Circuit Short to Battery | GO to Pinpoint Test C . |
| B1A01:13 | Speaker #1: Circuit Open | GO to Pinpoint Test C . |
| B1A02:11 | Speaker #2: Circuit Short to Ground | GO to Pinpoint Test C . |
| B1A02:12 | Speaker #2: Circuit Short to Battery | GO to Pinpoint Test C . |
| B1A02:13 | Speaker #2: Circuit Open | GO to Pinpoint Test C . |
| B1A03:11 | Speaker #3: Circuit Short to Ground | GO to Pinpoint Test C . |
| B1A03:12 | Speaker #3: Circuit Short to Battery | GO to Pinpoint Test C . |
| B1A03:13 | Speaker #3: Circuit Open | GO to Pinpoint Test C . |
| B1A04:11 | Speaker #4: Circuit Short to Ground | GO to Pinpoint Test C . |
| B1A04:12 | Speaker #4: Circuit Short to Battery | GO to Pinpoint Test C . |
| B1A04:13 | Speaker #4: Circuit Open | GO to Pinpoint Test C . |
| B1A05:11 | Speaker #5: Circuit Short to Ground | GO to Pinpoint Test C . |
| B1A05:12 | Speaker #5: Circuit Short to Battery | GO to Pinpoint Test C . |
| B1A05:13 | Speaker #5: Circuit Open | GO to Pinpoint Test C . |
| B1A06:11 | Speaker #6: Circuit Short to Ground | GO to Pinpoint Test C . |
| B1A06:12 | Speaker #6: Circuit Short to Battery | GO to Pinpoint Test C . |
| B1A06:13 | Speaker #6: Circuit Open | GO to Pinpoint Test C . |
| B1A07:11 | Speaker #7: Circuit Short to Ground | GO to Pinpoint Test C . |
| B1A07:12 | Speaker #7: Circuit Short to Battery | GO to Pinpoint Test C . |
| B1A07:13 | Speaker #7: Circuit Open | GO to Pinpoint Test C . |
| B1A08:11 | Speaker #8: Circuit Short to Ground | GO to Pinpoint Test C . |
| B1A08:12 | Speaker #8: Circuit Short to Battery | GO to Pinpoint Test C . |
| B1A08:13 | Speaker #8: Circuit Open | GO to Pinpoint Test C . |
| B1A09:11 | Speaker #9: Circuit Short to Ground | GO to Pinpoint Test C . |
| B1A09:12 | Speaker #9: Circuit Short to Battery | GO to Pinpoint Test C . |
| B1A09:13 | Speaker #9: Circuit Open | GO to Pinpoint Test C . |
| B1A10:11 | Speaker #10: Circuit Short to Ground | GO to Pinpoint Test C . |
| B1A10:12 | Speaker #10: Circuit Short to Battery | GO to Pinpoint Test C . |
| B1A10:13 | Speaker #10: Circuit Open | GO to Pinpoint Test C . |
| B1A11:11 | Speaker #11: Circuit Short to Ground | GO to Pinpoint Test C . |
| B1A11:12 | Speaker #11: Circuit Short to Battery | GO to Pinpoint Test C . |
| B1A11:13 | Speaker #11: Circuit Open | GO to Pinpoint Test C . |
| B1A12:11 | Speaker #12: Circuit Short to Ground | GO to Pinpoint Test C . |
| B1A12:12 | Speaker #12: Circuit Short to Battery | GO to Pinpoint Test C . |
| B1A12:13 | Speaker #12: Circuit Open | GO to Pinpoint Test C . |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test AB . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test AO . |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to Pinpoint Test AQ . |
| U0197:00 | Lost Communication With Telephone Control Module: No Sub Type Information | GO to Pinpoint Test AR . |
| U2014:41 | Control Module Hardware: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:41 is retrieved again, INSTALL a new audio Digital Signal Processing (DSP) module. REFER to Audio Digital Signal Processing (DSP) Module . REPEAT the self-test. |
| U2014:42 | Control Module Hardware: General Memory Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:42 is retrieved again, INSTALL a new audio DSP module. REFER to Audio Digital Signal Processing (DSP) Module . REPEAT the self-test. |
| U2014:4B | Control Module Hardware: Over Temperature | The audio DSP module was over-temperature. This can occur during extended use. Audio operation can resume after the audio DSP module cools. CLEAR the DTCs. This is normal operation. |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | Refer to MODULE CONFIGURATION . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | Refer to MODULE CONFIGURATION . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | Refer to MODULE CONFIGURATION . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AE . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AF . |
FRONT CONTROLS INTERFACE MODULE (FCIM) DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Action |
|---|---|---|
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test AB . |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to Pinpoint Test AQ . |
| U2013:63 | Switch Pack: Circuit / Component Protection Time-Out | GO to Pinpoint Test F . |
| U2014:41 | Control Module Hardware: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:41 is retrieved again, INSTALL a new Front Controls Interface Module (FCIM). REFER to FRONT CONTROLS INTERFACE MODULE (FCIM) - With Navigation or FRONT CONTROLS INTERFACE MODULE (FCIM) - Without Navigation . REPEAT the self-test. |
| U2014:42 | Control Module Hardware: General Memory Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:42 is retrieved again, INSTALL a new FCIM. REFER to FRONT CONTROLS INTERFACE MODULE (FCIM) - With Navigation or FRONT CONTROLS INTERFACE MODULE (FCIM) - Without Navigation . REPEAT the self-test. |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | INSTALL a new FCIM. REFER to FRONT CONTROLS INTERFACE MODULE (FCIM) - With Navigation or FRONT CONTROLS INTERFACE MODULE (FCIM) - Without Navigation . REPEAT the self-test. |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AG . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AH . |
FRONT DISPLAY INTERFACE MODULE (FDIM) DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Action |
|---|---|---|
| B1318 | Battery Voltage Low | GO to Pinpoint Test AI . |
| B1342 | ECU is Faulted |
NOTE:
Repair all other DTCs before diagnosing DTC B1342. CLEAR the DTCs. REPEAT the self-test. If DTC B1342 is the only DTC retrieved, INSTALL a new Front Display Interface Module (FDIM). REFER to FRONT DISPLAY INTERFACE MODULE (FDIM) - With Navigation
or FRONT DISPLAY INTERFACE MODULE (FDIM) - Without Navigation
. REPEAT the self-test. |
| B2477 | Module Configuration Failure | Refer to MODULE CONFIGURATION . |
| B2924 | Audio Button Stuck | GO to Pinpoint Test H . |
| U0140 | Lost Communication With Body Control Module (GEM) | GO to Pinpoint Test AB . |
| U0155 | Lost Communication With Instrument Panel Cluster (IC) Control Panel | GO to Pinpoint Test AO . |
| U0164 | Lost Communication With HVAC Control Module (EATC) | GO to Pinpoint Test AP . |
| U0184 | Lost Communication With Radio (ACM) | GO to Pinpoint Test AQ . |
| U0197 | Lost Communication With Telephone Control Module | GO to Pinpoint Test AR . |
| U2050 | No Application Present | Refer to MODULE CONFIGURATION . |
| U2051 | One or More Calibration Files Missing/Corrupt | Refer to MODULE CONFIGURATION . |
ACCESSORY PROTOCOL INTERFACE MODULE (APIM) DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Action |
|---|---|---|
| B1201:63 | Steering Wheel Audio Switch Pack 2: Circuit / Component Protection Time-Out | GO to Pinpoint Test M . |
| B1201:1C | Steering Wheel Audio Switch Pack 2: Circuit Voltage Out of Range | GO to Pinpoint Test M . |
| B1252:04 | USB Port: System Internal Failure | GO to Pinpoint Test Y . |
| B1252:11 | USB Port: Circuit Short to Ground | GO to Pinpoint Test Y . |
| B1D79:01 | Microphone Input: General Electrical Failure | GO to Pinpoint Test P . |
| U0100:00 | Lost Communication With ECM/PCM: No Sub Type Information | GO to Pinpoint Test AM . |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test AB . |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to Pinpoint Test AN . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test AO . |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to Pinpoint Test AQ . |
| U0255:00 | Lost Communication With Front Display Interface Module: No Sub Type Information | GO to Pinpoint Test AA . |
| U0256:00 | Lost Communication With Front Controls Interface Module: No Sub Type Information | GO to Pinpoint Test Z . |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | RETRIEVE and FOLLOW other DTCs present in the Accessory Protocol Interface Module (APIM) or Smart Junction Box (SJB). |
| U0423:00 | Invalid Data Received From Instrument Panel Control Module: No Sub Type Information | RETRIEVE and FOLLOW other DTCs present in the APIM or Instrument Panel Cluster (IPC). |
| U0485:00 | Invalid Data Received From Radio: No Sub Type Information | RETRIEVE and FOLLOW other DTCs present in the APIM or Audio Front Control Module (ACM). |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | Refer to MODULE CONFIGURATION . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | Refer to MODULE CONFIGURATION . |
| U3000:04 | Control Module: System Internal Failure | GO to Pinpoint Test W . |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:41 is still present, INSTALL a new APIM. REFER to Accessory Protocol Interface Module (APIM) . REPEAT the self-test. |
| U3000:42 | Control Module: General Memory Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:42 is still present, INSTALL a new APIM. REFER to Accessory Protocol Interface Module (APIM) . REPEAT the self-test. |
| U3000:88 | Control Module: Bus Off | Refer to MODULE COMMUNICATIONS NETWORK . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AK . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AJ . |
REMOTE FUNCTION ACTUATOR (RFA) MODULE DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Action |
|---|---|---|
| B125C:11 | Radio Mute Circuit: Short To Ground | GO to Pinpoint Test E . |
| B125C:15 | Radio Mute Circuit: Short To Battery or Open | GO to Pinpoint Test E . |
| All Other DTCs | - | REFER to the Diagnostic Trouble Code (DTC) Chart in MULTIFUNCTION ELECTRONIC MODULES . |