Information System And Entertainment System DTCS
AUDIO FRONT CONTROL MODULE (ACM) DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Action |
|---|---|---|
| B119F:01 | GPS Antenna: General Electrical Failure | GO to PINPOINT TEST T . |
| B119F:13 | GPS Antenna: Circuit Open | GO to PINPOINT TEST T . |
| B11BA:1C | Steering Wheel Audio Switch Pack: Circuit Voltage Out of Range | GO to PINPOINT TEST M . |
| B11BA:63 | Steering Wheel Audio Switch Pack: Circuit/Component Protection Time-Out | GO to PINPOINT TEST M . |
| B1201:1C | Steering Wheel Audio Switch Pack 2: Circuit Voltage Out of Range | GO to PINPOINT TEST M . |
| B1201:63 | Steering Wheel Audio Switch Pack 2: Circuit/Component Protection Time-Out | GO to PINPOINT TEST M . |
| B121C:01 | Hard Drive: General Electrical Failure | CLEAR the DTCs. REPEAT the self-test. If DTC B121C:01 is retrieved again, INSTALL a new Audio Front Control Module (ACM). REFER to AUDIO CONTROL MODULE (ACM) . REPEAT the self-test. |
| B1A05:01 | Speaker #5: General Electrical Failure | For Premium sound, GO to PINPOINT TEST B . For THX® sound, GO to PINPOINT TEST C . |
| B1A06:01 | Speaker #6: General Electrical Failure | For Premium sound, GO to PINPOINT TEST B . For THX® sound, GO to PINPOINT TEST C . |
| B1A07:01 | Speaker #7: General Electrical Failure |
NOTE:
This DTC is only applicable for vehicles with navigation, as it applies to the navigation voice circuits to the audio Digital Signal Processing (DSP) module. GO to PINPOINT TEST V
. |
| B1A56:21 | Antenna: Signal Amplitude < Minimum | GO to PINPOINT TEST A . |
| B1A89:01 | Satellite Antenna: General Electrical Failure | GO to PINPOINT TEST S . |
| B1A89:13 | Satellite Antenna: Circuit Open | GO to PINPOINT TEST S . |
| B1D19:49 | Compact Disc Unit: Internal Electronic Failure | CLEAR the DTCs. REPEAT the self-test. If DTC B1D19:49 is retrieved again, INSTALL a new ACM. REFER to AUDIO CONTROL MODULE (ACM) . REPEAT the self-test. |
| B1D19:4B | Compact Disc Unit: Over Temperature | The ACM was over-temperature. This may occur during extended use. Audio operation can resume after the ACM cools. CLEAR the DTCs. This is normal operation. |
| B1D79:01 | Microphone Input: General Electrical Failure | GO to PINPOINT TEST Q . |
| C1001:01 | Vision System Camera: General Electrical Failure | REFER to PARKING AID . |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to PINPOINT TEST AE . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to PINPOINT TEST AS . |
| U0162:00 | Lost Communication With Navigation Display Module: No Sub Type Information | GO to PINPOINT TEST J . |
| U0164:00 | Lost Communication With HVAC Control Module: No Sub Type Information | GO to PINPOINT TEST AJ . |
| U0196:00 | Lost Communication With Entertainment Control Module-Rear "A": No Sub Type Information | GO to PINPOINT TEST AU . |
| U0197:00 | Lost Communication With Telephone Control Module: No Sub Type Information | GO to PINPOINT TEST AQ . |
| U0238:00 | Lost Communication With Digital Audio Control Module "D": No Sub Type Information | GO to PINPOINT TEST AR . |
| U0256:00 | Lost Communication With Front Controls Interface Module: No Sub Type Information | GO to PINPOINT TEST AX . |
| U2014:09 | Control Module Hardware: Component Failure | GO to PINPOINT TEST U . |
| U2014:41 | Control Module Hardware: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:41 is retrieved again, INSTALL a new ACM. REFER to AUDIO CONTROL MODULE (ACM) . REPEAT the self-test. |
| U2014:96 | Control Module Hardware: Component Internal Failure | GO to PINPOINT TEST R . |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | PROGRAM the ACM. REFER to Programmable Module Installation (PMI) in MODULE CONFIGURATION . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | PROGRAM the ACM. REFER to PMI in MODULE CONFIGURATION . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | PROGRAM the ACM. REFER to PMI in MODULE CONFIGURATION . |
| U3000:45 | Control Module: Program Memory Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:45 is retrieved again, INSTALL a new ACM. REFER to AUDIO CONTROL MODULE (ACM) . REPEAT the self-test. |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AF . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AG . |
FRONT CONTROLS INTERFACE MODULE (FCIM) DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Action |
|---|---|---|
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to PINPOINT TEST AE . |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to PINPOINT TEST AT . |
| U2013:63 | Switch Pack: Circuit/Component Protection Time-Out | GO to PINPOINT TEST F . |
| U2014:41 | Control Module Hardware: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:41 is retrieved again, INSTALL a new Front Controls Interface Module (FCIM). REFER to FRONT CONTROLS INTERFACE MODULE (FCIM) . REPEAT the self-test. |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | PROGRAM the FCIM. REFER to Programmable Module Installation (PMI) in MODULE CONFIGURATION . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AH . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AI . |
ACCESSORY PROTOCOL INTERFACE MODULE (APIM) DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Action |
|---|---|---|
| B1252:04 | USB Port: System Internal Failure | GO to PINPOINT TEST Z . |
| B1252:11 | USB Port: Circuit Short to Ground | GO to PINPOINT TEST Z . |
| B1D79:01 | Microphone Input: General Electrical Failure | GO to PINPOINT TEST Q . |
| U0100:00 | Lost Communication With ECM/PCM: No Sub Type Information | GO to PINPOINT TEST AV . |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to PINPOINT TEST AE . |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to PINPOINT TEST AW . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to PINPOINT TEST AS . |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to PINPOINT TEST AT . |
| U0196:00 | Lost Communication With Entertainment Control Module-Rear "A": No Sub Type Information | GO to PINPOINT TEST AU . |
| U0256:00 | Lost Communication With Front Controls Interface Module: No Sub Type Information | GO to PINPOINT TEST AX . |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | RETRIEVE and FOLLOW other DTCs present in the Accessory Protocol Interface Module (APIM) or Smart Junction Box (SJB). |
| U0423:00 | Invalid Data Received From Instrument Panel Control Module: No Sub Type Information | RETRIEVE and FOLLOW other DTCs present in the APIM or Instrument Panel Cluster (IPC). |
| U0485:00 | Invalid Data Received From Radio: No Sub Type Information | RETRIEVE and FOLLOW other DTCs present in the APIM or Audio Front Control Module (ACM). |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | PROGRAM the APIM. REFER MODULE CONFIGURATION . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | PROGRAM the APIM. refer to MODULE CONFIGURATION . |
| U3000:04 | Control Module: System Internal Failure | GO to PINPOINT TEST X . |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:41 is still present, INSTALL a new APIM. REFER to ACCESSORY PROTOCOL INTERFACE MODULE (APIM) . REPEAT the self-test. |
| U3000:42 | Control Module: General Memory Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:42 is still present, INSTALL a new APIM. REFER to ACCESSORY PROTOCOL INTERFACE MODULE (APIM) . REPEAT the self-test. |
| U3000:88 | Control Module: Bus Off | REFER to MODULE COMMUNICATIONS NETWORK to diagnose the observed symptom. |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AL . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AK . |
AUDIO DIGITAL SIGNAL PROCESSING (DSP) MODULE DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Action |
|---|---|---|
| B1A01:11 | Speaker #1: Circuit Short to Ground | GO to PINPOINT TEST C . |
| B1A01:12 | Speaker #1: Circuit Short to Battery | GO to PINPOINT TEST C . |
| B1A01:13 | Speaker #1: Circuit Open | GO to PINPOINT TEST C . |
| B1A02:11 | Speaker #2: Circuit Short to Ground | GO to PINPOINT TEST C . |
| B1A02:12 | Speaker #2: Circuit Short to Battery | GO to PINPOINT TEST C . |
| B1A02:13 | Speaker #2: Circuit Open | GO to PINPOINT TEST C . |
| B1A03:11 | Speaker #3: Circuit Short to Ground | GO to PINPOINT TEST C . |
| B1A03:12 | Speaker #3: Circuit Short to Battery | GO to PINPOINT TEST C . |
| B1A03:13 | Speaker #3: Circuit Open | GO to PINPOINT TEST C . |
| B1A04:11 | Speaker #4: Circuit Short to Ground | GO to PINPOINT TEST C . |
| B1A04:12 | Speaker #4: Circuit Short to Battery | GO to PINPOINT TEST C . |
| B1A04:13 | Speaker #4: Circuit Open | GO to PINPOINT TEST C . |
| B1A05:11 | Speaker #5: Circuit Short to Ground | GO to PINPOINT TEST C . |
| B1A05:12 | Speaker #5: Circuit Short to Battery | GO to PINPOINT TEST C . |
| B1A05:13 | Speaker #5: Circuit Open | GO to PINPOINT TEST C . |
| B1A06:11 | Speaker #6: Circuit Short to Ground | GO to PINPOINT TEST C . |
| B1A06:12 | Speaker #6: Circuit Short to Battery | GO to PINPOINT TEST C . |
| B1A06:13 | Speaker #6: Circuit Open | GO to PINPOINT TEST C . |
| B1A07:11 | Speaker #7: Circuit Short to Ground | GO to PINPOINT TEST C . |
| B1A07:12 | Speaker #7: Circuit Short to Battery | GO to PINPOINT TEST C . |
| B1A07:13 | Speaker #7: Circuit Open | GO to PINPOINT TEST C . |
| B1A08:11 | Speaker #8: Circuit Short to Ground | GO to PINPOINT TEST C . |
| B1A08:12 | Speaker #8: Circuit Short to Battery | GO to PINPOINT TEST C . |
| B1A08:13 | Speaker #8: Circuit Open | GO to PINPOINT TEST C . |
| B1A09:11 | Speaker #9: Circuit Short to Ground | GO to PINPOINT TEST C . |
| B1A09:12 | Speaker #9: Circuit Short to Battery | GO to PINPOINT TEST C . |
| B1A09:13 | Speaker #9: Circuit Open | GO to PINPOINT TEST C . |
| B1A10:11 | Speaker #10: Circuit Short to Ground | GO to PINPOINT TEST C . |
| B1A10:12 | Speaker #10: Circuit Short to Battery | GO to PINPOINT TEST C . |
| B1A10:13 | Speaker #10: Circuit Open | GO to PINPOINT TEST C . |
| B1A11:11 | Speaker #11: Circuit Short to Ground | GO to PINPOINT TEST C . |
| B1A11:12 | Speaker #11: Circuit Short to Battery | GO to PINPOINT TEST C . |
| B1A11:13 | Speaker #11: Circuit Open | GO to PINPOINT TEST C . |
| B1A12:11 | Speaker #12: Circuit Short to Ground | GO to PINPOINT TEST C . |
| B1A12:12 | Speaker #12: Circuit Short to Battery | GO to PINPOINT TEST C . |
| B1A12:13 | Speaker #12: Circuit Open | GO to PINPOINT TEST C . |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to PINPOINT TEST AE . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to PINPOINT TEST AS . |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to PINPOINT TEST AT . |
| U0196:00 | Lost Communication With Entertainment Control Module-Rear "A": No Sub Type Information | GO to PINPOINT TEST AU . |
| U0197:00 | Lost Communication With Telephone Control Module: No Sub Type Information | GO to PINPOINT TEST AQ . |
| U2014:41 | Control Module Hardware: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:41 is retrieved again, INSTALL a new audio DSP module. REFER to AUDIO DIGITAL SIGNAL PROCESSING (DSP) MODULE . REPEAT the self-test. |
| U2014:42 | Control Module Hardware: General Memory Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:42 is retrieved again, INSTALL a new audio DSP module. REFER to AUDIO DIGITAL SIGNAL PROCESSING (DSP) MODULE . REPEAT the self-test. |
| U2014:4B | Control Module Hardware: Over Temperature | The audio DSP module was over-temperature. This can occur during extended use or high ambient temperatures. CLEAR the DTCs. This is normal operation. |
| U2014:96 | Control Module Hardware: Component Internal Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:96 is retrieved again, INSTALL a new audio DSP module. REFER to AUDIO DIGITAL SIGNAL PROCESSING (DSP) MODULE . REPEAT the self-test. |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | PROGRAM the audio DSP module. REFER to Programmable Module Installation (PMI) in MODULE CONFIGURATION . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | PROGRAM the audio DSP module. REFER to PMI in MODULE CONFIGURATION . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | PROGRAM the audio DSP module. REFER to PMI in MODULE CONFIGURATION . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AO . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AP . |
REAR ENTERTAINMENT MODULE (RETM) DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Action |
|---|---|---|
| B119D:04 | Single-Disc DVD Player: System Internal Failure | GO to PINPOINT TEST AC . |
| B119D:87 | Single-Disc DVD Player: Missing Message | GO to SYMPTOM CHART - FAMILY ENTERTAINMENT SYSTEM to diagnose the observed symptom. |
| B1350:04 | Single-Disc DVD #2: System Internal Failure | GO to PINPOINT TEST AC . |
| B1350:87 | Single-Disc DVD #2: Missing Message | GO to SYMPTOM CHART - FAMILY ENTERTAINMENT SYSTEM to diagnose the observed symptom. |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to PINPOINT TEST AE . |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to PINPOINT TEST AT . |
| U2004:63 | Auxiliary Switch Pack: Circuit/Component Protection Time-Out | GO to PINPOINT TEST G . |
| U2013:63 | Switch Pack: Circuit/Component Protection Time-Out | GO to PINPOINT TEST G . |
| U3000:04 | Control Module: System Internal Failure | GO to PINPOINT TEST X . |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:14 is retrieved again, INSTALL a new Rear Entertainment Module (RETM). REFER to REAR ENTERTAINMENT MODULE (RETM) . REPEAT the self-test. |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AN . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AM . |
REMOTE FUNCTION ACTUATOR (RFA) MODULE DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Action |
|---|---|---|
| B125C:11 | Radio Mute Circuit: Short to Ground | For Premium sound, GO to PINPOINT TEST D . For THX® sound, GO to PINPOINT TEST E . |
| B125C:15 | Radio Mute Circuit: Short to Battery or Open | For Premium sound, GO to PINPOINT TEST D . For THX® sound, GO to PINPOINT TEST E . |