Rear View Mirror DTCS: Interior
IPM-A DTC CHART
| DTC | Description | Action |
|---|---|---|
| B11C7:46 | High Beam Sensor: Calibration/Parameter Memory Failure | PROGRAM the IPM-A. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . REPEAT the IPM-A self-test. If the DTC returns, INSTALL a new interior rear view mirror - auto high beam. REFER to INTERIOR REAR VIEW MIRROR . |
| B11C7:97 | High Beam Sensor: Component or System Operation Obstructed or Blocked | REFER to EXTERIOR LIGHTING . |
| B1286:14 | Interior Mirror: Circuit Short To Ground or Open | GO to PINPOINT TEST C . |
| B12D8:11 | Mirror Heater Output: Circuit Short To Ground | GO to PINPOINT TEST D . |
| B12D8:13 | Mirror Heater Output: Circuit Open | GO to PINPOINT TEST D . |
| B13A6:14 | Lane Departure Warning (LDW) Switch Input: Circuit Short To Ground or Open | REFER to LANE DEPARTURE WARNING . |
| C1001:78 | Vision System Camera: Alignment or Adjustment Incorrect | This DTC sets when a new IPM-A has been installed without performing the camera alignment. PERFORM the camera alignment using a scan tool. |
| U0100:87 | Lost Communication With ECM/PCM "A": Missing Message | GO to PINPOINT TEST E . |
| U0104:87 | Lost Communication With Cruise Control Module: Missing Message | GO to PINPOINT TEST F . |
| U0131:87 | Lost Communication With Power Steering Control Module: Missing Message | GO to PINPOINT TEST G . |
| U0140:87 | Lost Communication With Body Control Module: Missing Message | GO to PINPOINT TEST H . |
| U0151:87 | Lost Communication With Restraints Control Module: Missing Message | GO to PINPOINT TEST I . |
| U0155:87 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: Missing Message | GO to PINPOINT TEST J . |
| U0212:87 | Lost Communication With Steering Column Control Module: Missing Message | GO to PINPOINT TEST K . |
| U0232:87 | Lost Communication With Side Obstacle Detection Control Module - Left: Missing Message | GO to PINPOINT TEST L . |
| U0233:87 | Lost Communication With Side Obstacle Detection Control Module - Right: Missing Message | GO to PINPOINT TEST L . |
| U0401:00 | Invalid Data Received from ECM/PCM A: No Sub Type Information | This DTC can set due to a fault in the PCM. CARRY OUT a self-test of the PCM and DIAGNOSE any PCM DTCs present. REFER to ELECTRONIC ENGINE CONTROLS . |
| U0405:00 | Invalid Data Received From Cruise Control Module: No Sub Type Information | This DTC can set due to a fault in the C-CM. CARRY OUT a self-test of the C-CM and DIAGNOSE any C-CM DTCs present. Refer to CRUISE CONTROL - ADAPTIVE . |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | This DTC can set due to a fault in the BCM. CARRY OUT a self-test of the BCM and DIAGNOSE any BCM DTCs present. REFER to MULTIFUNCTION ELECTRONIC MODULES . |
| U0423:00 | Invalid Data Received from Instrument Panel Cluster Control Module: No Sub Type Information | This DTC can set due to a fault in the IPC. CARRY OUT a self-test of the IPC and DIAGNOSE any IPC DTCs present. REFER to INSTRUMENTATION, MESSAGE CENTER, AND WARNING CHIMES . |
| U0429:00 | Invalid Data Received From Steering Column Control Module: No Sub Type Information | This DTC can set due to a fault in the SCCM. CARRY OUT a self-test of the SCCM and DIAGNOSE any SCCM DTCs present. REFER to STEERING COLUMN SWITCHES . |
| U0452:00 | Invalid Data Received From Restraints Control Module: No Sub Type Information | This DTC can set due to a fault in the RCM. CARRY OUT a self-test of the RCM and DIAGNOSE any RCM DTCs present. Refer to SUPPLEMENTAL RESTRAINT SYSTEM . |
| U1000:11 | Solid State Driver Protection Active - Driver Disabled: Circuit Short To Ground | The IPM-A has temporarily disabled an output because an excessive current draw exists from a short to ground). The IPMA cannot enable the output until the cause of the short is corrected. ADDRESS all other IPM-A DTCs first. After the cause of the concern is corrected, CLEAR the DTCs. REPEAT the IPM-A self-test. |
| U201A:54 | Control Module Main Calibration Data: Missing Calibration | PROGRAM the IPM-A. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . REPEAT the IPM-A self-test. If the DTC returns, INSTALL a new interior rear view mirror - auto high beam. REFER to INTERIOR REAR VIEW MIRROR . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | PROGRAM the IPM-A. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . REPEAT the IPM-A self-test. If the DTC returns, INSTALL a new interior rear view mirror - auto high beam. REFER to INTERIOR REAR VIEW MIRROR . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | PROGRAM the IPM-A. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . REPEAT the IPM-A self-test. If the DTC returns, INSTALL a new interior rear view mirror - auto high beam. REFER to INTERIOR REAR VIEW MIRROR . |
| U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | PROGRAM the IPM-A. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI) . REPEAT the IPM-A self-test. If the DTC returns, INSTALL a new interior rear view mirror - auto high beam. REFER to INTERIOR REAR VIEW MIRROR . |
| U3000:42 | Control Module: General Memory Failure | INSTALL a new interior rear view mirror - auto high beam. REFER to INTERIOR REAR VIEW MIRROR . |
| U3000:49 | Control Module: Internal Electronic Failure | INSTALL a new interior rear view mirror - auto high beam. REFER to INTERIOR REAR VIEW MIRROR . |
| U3000:93 | Control Module: No Operation | INSTALL a new interior rear view mirror - auto high beam. REFER to INTERIOR REAR VIEW MIRROR . |
| U3000:96 | Control Module: Component Internal Failure | INSTALL a new interior rear view mirror - auto high beam. REFER to INTERIOR REAR VIEW MIRROR . |