Audio Front Control Module (ACM) - With Navigation
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| B119F:01 | GPS Antenna: General Electrical Failure | GO to Pinpoint Test N . |
| B119F:13 | GPS Antenna: Circuit Open | GO to Pinpoint Test N . |
| B11BA:1C | Steering Wheel Audio Switch Pack: Circuit Voltage Out of Range | GO to Pinpoint Test U . |
| B11BA:63 | Steering Wheel Audio Switch Pack: Circuit/Component Protection Time-Out | GO to Pinpoint Test U . |
| B1201:1C | Steering Wheel Audio Switch Pack 2: Circuit Voltage Out of Range | GO to Pinpoint Test U . |
| B1201:63 | Steering Wheel Audio Switch Pack 2: Circuit/Component Protection Time-Out | GO to Pinpoint Test U . |
| B121C:01 | Hard Drive: General Electrical Failure | CLEAR the DTCs. REPEAT the self-test. If DTC B121C:01 is retrieved again, INSTALL a new Audio Front Control Module (ACM). REFER to Audio Control Module (ACM) . REPEAT the self-test. |
| B1A01:01 | Speaker #1: General Electrical Failure | For Expedition, GO to Pinpoint Test D
. For Navigator, GO to Pinpoint Test E . |
| B1A02:01 | Speaker #2: General Electrical Failure | For Expedition, GO to Pinpoint Test D
. For Navigator, GO to Pinpoint Test E . |
| B1A03:01 | Speaker #3: General Electrical Failure | For Expedition, GO to Pinpoint Test D
. For Navigator, GO to Pinpoint Test E . |
| B1A04:01 | Speaker #4: General Electrical Failure | For Expedition, GO to Pinpoint Test D
. For Navigator, GO to Pinpoint Test E . |
| B1A05:01 | Speaker #5: General Electrical Failure | For Expedition, GO to Pinpoint Test H
. For Navigator, GO to Pinpoint Test E . |
| B1A06:01 | Speaker #6: General Electrical Failure | GO to Pinpoint Test E . |
| B1A56:21 | Antenna: Signal Amplitude < Minimum |
NOTE:
If DTC B1A56:21 sets after running the bezel diagnostic tests disregard this DTC. This test is used for end of line or repair bay testing at the Ford plant. Each plant has its own assigned frequency and signal strength requirements. The running and passing of this test depends on local radio stations. If no local station is broadcasting on the required frequency the test will fail. Therefore test ran from the bezel diagnostic screen and the DTC generated from the test can be disregarded. DISREGARD this DTC. |
| B1A89:01 | Satellite Antenna: General Electrical Failure | GO to Pinpoint Test K . |
| B1A89:13 | Satellite Antenna: Circuit Open | GO to Pinpoint Test K . |
| B1D19:49 | Compact Disc Unit: Internal Electronic Failure | CLEAR the DTCs. REPEAT the self-test. If DTC B1D19:49 is retrieved again, INSTALL a new ACM . REFER to Audio Control Module (ACM) . REPEAT the self-test. |
| B1D19:4B | Compact Disc Unit: Over Temperature | The ACM was over-temperature. This may occur during extended use. Audio operation can resume after the ACM cools. CLEAR the DTCs. This is normal operation. |
| B1D79:01 | Microphone Input: General Electrical Failure | GO to Pinpoint Test AA . |
| C1001:01 | Vision System Camera: General Electrical Failure | REFER to DIAGNOSIS AND TESTING . |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test AR . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test AS . |
| U0159:00 | Lost Communication With Parking Assist Control Module "A": No Sub Type Information | GO to Pinpoint Test AB . |
| U0197:00 | Lost Communication With Telephone Control Module: No Sub Type Information | GO to Pinpoint Test AM . |
| U0238:00 | Lost Communication With Digital Audio Control Module "D": No Sub Type Information |
NOTE:
This DTC only applies to Navigator. For Expedition, disregard the DTC. GO to Pinpoint Test G
. |
| U0249:00 | Lost Communication With Entertainment Control Module-Rear "B": No Sub Type Information | GO to Pinpoint Test AN . |
| U2013:63 | Switch Pack: Circuit/Component Protection Time-Out | GO to Pinpoint Test Y . |
| U2014:09 | Control Module Hardware: Component Failure | GO to Pinpoint Test O . |
| U2014:41 | Control Module Hardware: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:41 is retrieved again, INSTALL a new ACM . REFER to Audio Control Module (ACM) . REPEAT the self-test. |
| U2014:96 | Control Module Hardware: Component Internal Failure | GO to Pinpoint Test M . |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | REFER to MODULE CONFIGURATION . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | REFER to MODULE CONFIGURATION . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | REFER to MODULE CONFIGURATION . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AH . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AI . |