Vehicle Dynamic Suspension DTCS
Diagnostics in this information assume a certain skill level and knowledge of Ford-specific diagnostic practices. Refer to Diagnostic Methods in Service Information for information about these practices.
DTC INDEX
| DTCs | Description | Action |
|---|---|---|
| C110C:11 | Left Front Damper Solenoid: Circuit Shorted to Ground | GO to Pinpoint Test D . |
| C110C:12 | Left Front Damper Solenoid: Circuit Shorted to Battery | GO to Pinpoint Test D . |
| C110C:13 | Left Front Damper Solenoid: Circuit Open | GO to Pinpoint Test D . |
| C110D:11 | Right Front Damper Solenoid: Circuit Shorted to Ground | GO to Pinpoint Test D . |
| C110D:12 | Right Front Damper Solenoid: Circuit Shorted to Battery | GO to Pinpoint Test D . |
| C110D:13 | Right Front Damper Solenoid: Circuit Open | GO to Pinpoint Test D . |
| C110E:11 | Left Rear Damper Solenoid: Circuit Shorted to Ground | GO to Pinpoint Test D . |
| C110E:12 | Left Rear Damper Solenoid: Circuit Shorted to Battery | GO to Pinpoint Test D . |
| C110E:13 | Left Rear Damper Solenoid: Circuit Open | GO to Pinpoint Test D . |
| C110F:11 | Right Rear Damper Solenoid: Circuit Shorted to Ground | GO to Pinpoint Test D . |
| C110F:12 | Right Rear Damper Solenoid: Circuit Shorted to Battery | GO to Pinpoint Test D . |
| C110F:13 | Right Rear Damper Solenoid: Circuit Open | GO to Pinpoint Test D . |
| C1124:55 | Height Sensor(s): Not Configured | This DTC is automatically set in a new VDM and indicates that the system requires height sensor calibration. Once the system is calibrated, the DTC can be cleared. CALIBRATE the VDM and sensors. FOLLOW the scan tool instructions. |
| C1A03:11 | Left Front Height Sensor: Circuit Shorted to Ground | GO to Pinpoint Test E . |
| C1A03:12 | Left Front Height Sensor: Circuit Shorted to Battery | GO to Pinpoint Test E . |
| C1A04:11 | Right Front Height Sensor: Circuit Shorted to Ground | GO to Pinpoint Test E . |
| C1A04:12 | Right Front Height Sensor: Circuit Shorted to Battery | GO to Pinpoint Test E . |
| C1A05:11 | Left Rear Height Sensor: Circuit Shorted to Ground | GO to Pinpoint Test E . |
| C1A05:12 | Left Rear Height Sensor: Circuit Shorted to Battery | GO to Pinpoint Test E . |
| C1A06:11 | Right Rear Height Sensor: Circuit Shorted to Ground | GO to Pinpoint Test E . |
| C1A06:12 | Right Rear Height Sensor: Circuit Shorted to Battery | GO to Pinpoint Test E . |
| P1758:19 | Pressure Solenoid Control System Incorrect Current: Circuit Current Above Threshold | GO to Pinpoint Test C . |
| U0001:88 | High Speed CAN Communications Bus: Bus Off | REFER to Module Communications Network to diagnose the no communication concern. |
| U0100:87 | Lost Communication with ECM /PCM A: Missing Message | GO to Pinpoint Test F . |
| U0121:87 | Lost Communication with ABS Control Module: Missing Message | GO to Pinpoint Test G . |
| U0126:87 | Lost Communication with SASM : Missing Message | GO to Pinpoint Test H . |
| U0140:87 | Lost Communication with BCM : Missing Message | GO to Pinpoint Test I . |
| U0151:87 | Lost Communication with RCM : Missing Message | GO to Pinpoint Test J . |
| U0155:87 | Lost Communication with IPC : Missing Message | GO to Pinpoint Test K . |
| U0253:87 | Lost Communication with APIM : Missing Message | GO to Pinpoint Test L . |
| U0401:00 | Invalid Data Received from ECM /PCM A: No Sub Type Information | This DTC sets when the VDM module receives invalid network data from the PCM. RETRIEVE and REPAIR all non-network DTCs in the PCM. REFER to Electronic Engine Controls . |
| U0415:00 | Invalid Data Received from ABS Control Module: No Sub Type Information | This DTC sets when the VDM module receives invalid network data from the ABS module. RETRIEVE and REPAIR all non-network DTCs in the ABS module. REFER to Anti-Lock Brake System (ABS) and Stability . |
| U0428:00 | Invalid Data Received from SASM : No Sub Type Information | This DTC sets when the VDM module receives invalid network data from the SASM. RETRIEVE and REPAIR all non-network DTCs in the SASM. REFER to Steering Column Switches . |
| U0452:00 | Invalid Data Received from RCM : No Sub Type Information | This DTC sets when the VDM module receives invalid network data from the RCM. RETRIEVE and REPAIR all non-network DTCs in the RCM. REFER to Supplemental Restraint System . |
| U200D:11 | Control Module Output Power A: Circuit Short to Ground | GO to Pinpoint Test E . |
| U200D:12 | Control Module Output Power A: Circuit Short to Battery | GO to Pinpoint Test E . |
| U200E:11 | Control Module Output Power B: Circuit Short to Ground | GO to Pinpoint Test E . |
| U200E:12 | Control Module Output Power B: Circuit Short to Battery | GO to Pinpoint Test E . |
| U201A:00 | Control Module Main Calibration Data: No Sub Type Information | CHECK the service history for recent service actions related to the VDM module. This DTC sets due to incomplete or improper module configuration. If there have been recent service actions with this module, REPEAT the PMI using as-built data. If there have been no recent service actions INSTALL a new VDM module. REFER to Vehicle Dynamics Module (VDM) in this section. |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CHECK the service history for recent service actions related to the VDM module. This DTC sets due to incomplete or improper module configuration. If there have been recent service actions with this module, REPEAT the PMI using as-built data. If there have been no recent service actions INSTALL a new VDM module. REFER to Vehicle Dynamics Module (VDM) in this section. |
| U3000:04 | Control Module: System Internal Failure | CLEAR the DTC. CARRY OUT the VDM module self-test. RETRIEVE and RECORD all DTCs. If the DTC returns, INSTALL a new VDM module. REFER to Vehicle Dynamics Module (VDM) . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test A . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test B . |