| B106E |
Solid State Driver Disabled Due to Short Circuit |
GO to Pinpoint Test A
. |
| B106F |
Module Disabled Due to External Fault |
DIAGNOSE DTC B106E first. If the cause of the concern was repaired and this DTC is still present after a self-test, INSTALL a new Liftgate/Trunk Module (LTM). REFER to Liftgate/Trunk Module (LTM)
. |
| B107D |
Obstacle Detected While Closing |
GO to Pinpoint Test D
. |
| B1105 |
Rear Open/Close Switch Active During Self-Test |
GO to Pinpoint Test B
. |
| B1179 |
Latch Motor Circuit Short to Battery |
GO to Pinpoint Test A
. |
| B117A |
Latch Motor Circuit Short to Ground |
GO to Pinpoint Test A
. |
| B117B |
Latch Motor Circuit Open |
GO to Pinpoint Test A
. |
| B117C |
Latch Centering Switch Invalid |
GO to Pinpoint Test J
. |
| B1317 |
Battery Voltage High |
GO to Pinpoint Test K
. |
| B1318 |
Battery Voltage Low |
GO to Pinpoint Test L
. |
| B1342 |
ECU Is Faulted |
INSTALL a new LTM. REFER to Liftgate/Trunk Module (LTM)
. |
| B2019 |
Liftgate Exceeded Time Allowed to Cinch Door |
GO to Pinpoint Test C
. |
| B201A |
Power System Disabled Due to High Manual Closing Speed |
GO to Pinpoint Test I
. |
| B236A |
Chime Output Circuit Open |
GO to Pinpoint Test E
. |
| B2418 |
Sensor Power Short to Ground |
GO to Pinpoint Test A
. |
| B2419 |
Sensor 1 Invalid |
GO to Pinpoint Test A
. |
| B2420 |
Sensor 2 Invalid |
GO to Pinpoint Test A
. |
| B2552 |
Vbatt 2 Circuit Open |
GO to Pinpoint Test A
. |
| B2699 |
Left Pinch Strip Open or Short to Battery |
GO to Pinpoint Test G
. |
| B2700 |
Right Pinch Strip Open or Short to Battery |
GO to Pinpoint Test G
. |
| B2701 |
Left Pinch Strip Stuck Active |
GO to Pinpoint Test G
. |
| B2702 |
Right Pinch Strip Stuck Active |
GO to Pinpoint Test G
. |
| B2703 |
Open/Close Switch Stuck Active |
GO to Pinpoint Test B
. |
| B2718 |
Liftgate/Decklid Ajar Output Short to Battery |
DIAGNOSE the courtesy lamps staying on continuously. REFER to
Interior Lighting
. |
| B2721 |
Liftgate/Decklid Ajar Output Short to Ground or Open |
DIAGNOSE the courtesy lamps inoperative from the liftgate or on continuously. REFER to
Interior Lighting
. |
| B2723 |
Glass Position Switch Active During Selftest |
DIAGNOSE the courtesy lamps staying on continuously. REFER to
Interior Lighting
. |
| B2819 |
Gate Motor Circuit Short to Battery |
GO to Pinpoint Test A
. |
| B2903 |
Chime Output Circuit Short to Battery |
GO to Pinpoint Test E
. |
| B2908 |
Latch Switch Invalid |
If the power liftgate is inoperative, GO to Pinpoint Test A
. If the power liftgate stops in secondary latch position, GO to Pinpoint Test C
. |
| B2935 |
Drive Unit Failure |
GO to Pinpoint Test A
. |
| B2936 |
Gate Motor Open |
GO to Pinpoint Test A
. |
| B2937 |
Gate Motor Short to Ground |
GO to Pinpoint Test A
. |
| B2939 |
Gate Clutch Short to Ground or Open |
GO to Pinpoint Test A
. |
| B2940 |
Chime Output Circuit Short to Ground |
GO to Pinpoint Test E
. |
| U0140 |
Lost Communication With Body Control Module (GEM) |
GO to Pinpoint Test M
. |
| U0155 |
Lost Communication With Instrument Panel Cluster (IC) Control Module |
GO to Pinpoint Test N
. |
| U2050 |
No Application Present |
INSTALL a new LTM. REFER to Liftgate/Trunk Module (LTM)
. |
| U2051 |
One or More Calibration Files Missing/Corrupt |
INSTALL a new LTM. REFER to Liftgate/Trunk Module (LTM)
. |
| U2471 |
Unexpected PRNDL State |
VERIFY the transmission gear selector (PRNDL) is in PARK. CLEAR the DTCs. REPEAT the self-test. If DTC U2471 is retrieved again, RETRIEVE and FOLLOW non-network DTCs from the PCM and Instrument Panel Cluster(IPC) module. REFER to
Electronic Engine Controls
or
Instrumentation, Message Center, and Warning Chimes
. If no DTCs are present, INSTALL a new LTM. REFER to Liftgate/Trunk Module (LTM)
. |
| U2472 |
Unexpected Ignition State |
VERIFY the ignition is in RUN mode. CLEAR the DTCs. REPEAT the self-test. If DTC U2472 is retrieved again, RETRIEVE and FOLLOW non-network DTCs from the BCM. REFER to
Multifunction Electronic Modules
. If no DTCs are present, INSTALL a new LTM. REFER to Liftgate/Trunk Module (LTM)
. |
| U2473 |
Unexpected Vehicle Speed (VSS) |
CLEAR the DTCs. REPEAT the self-test. If DTC U2473 is retrieved again, RETRIEVE and FOLLOW non-network DTCs from the PCM or the ABS module. REFER to
Electronic Engine Controls
or
Anti-Lock Brake System (ABS) and Stability Control
to diagnose the vehicle speed related input. If no related DTCs or symptoms are present, INSTALL a new LTM. REFER to Liftgate/Trunk Module (LTM)
. |