Audio Front Control Module (ACM)
| DTC | Description | Action |
|---|---|---|
| B1A56:21 | Antenna: Signal Amplitude < Minimum | If DTC B1A56:21 sets after running the bezel diagnostic tests, disregard this DTC. This test is used for end of line or repair bay testing at the Ford plant. Each plant has its own assigned frequency and signal strength requirements. The running and passing of this test depends on local radio stations. If no local station is broadcasting on the required frequency, the test will fail. |
| B1A89:11 | Satellite Antenna: Circuit Short To Ground | For a satellite radio concern, GO to Pinpoint Test B
. For a SIRIUS Travel Link concern, GO to Pinpoint Test AU . For a navigation concern (if equipped), GO to Pinpoint Test AB . For a compass concern. GO to Pinpoint Test AD . |
| B1A89:13 | Satellite Antenna: Circuit Open | For a satellite radio concern, GO to Pinpoint Test B
. For a SIRIUS Travel Link concern, GO to Pinpoint Test AU . For a navigation concern (if equipped), GO to Pinpoint Test AB . For a compass concern. GO to Pinpoint Test AD . |
| B1D19:49 | Compact Disc Unit: Internal Electronic Failure | GO to Pinpoint Test U . |
| B1D19:4B | Compact Disc Unit: Over Temperature | GO to Pinpoint Test U . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test AI . |
| U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test AP . |
| U0256:00 | Lost Communication With Front Controls Interface Module "A": No Sub Type Information | GO to Pinpoint Test AQ . |
| U0257:00 | Lost Communication With Front Controls / Display Interface Module: No Sub Type Information | GO to Pinpoint Test AR . |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | This DTC sets due to incomplete or incorrect PMI procedures. CHECK the vehicle service history for recent service actions related to the ACM. If there have been recent service actions with the ACM, INSTALL as-built data from PTS, following the diagnostic scan tool instructions under Module Programming>As-Built. If there have been no recent service actions, INSTALL a new ACM to correct the failure to retain configuration data. REFER to Audio Control Module (ACM) . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | This DTC sets due to incomplete or incorrect PMI procedures. CHECK the vehicle service history for recent service actions related to the ACM. If there have been recent service actions with the ACM, INSTALL as-built data from PTS, following the diagnostic scan tool instructions under Module Programming>As-Built. If there have been no recent service actions, INSTALL a new ACM to correct the failure to retain configuration data. REFER to Audio Control Module (ACM) . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | This DTC sets due to incomplete or incorrect PMI procedures. CHECK the vehicle service history for recent service actions related to the ACM. If there have been recent service actions with the ACM, INSTALL as-built data from PTS, following the diagnostic scan tool instructions under Module Programming>As-Built. If there have been no recent service actions, INSTALL a new ACM to correct the failure to retain configuration data. REFER to Audio Control Module (ACM) . |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the DTC. WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:41 is retrieved again, INSTALL a new ACM. REFER to Audio Control Module (ACM) . |
| U3000:42 | Control Module: General Memory Failure | CLEAR the DTC. WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:42 is retrieved again, INSTALL a new ACM. REFER to Audio Control Module (ACM) . |
| U3000:96 | Control Module: Component Internal Failure | CLEAR the DTC. WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:96 is retrieved again, INSTALL a new ACM. REFER to Audio Control Module (ACM) . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AS . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AT . |