DSP Module
| DTC | Description | Action |
|---|---|---|
| B13FB:11 | Audio Enable Line: Circuit Short To Ground | GO to Pinpoint Test E . |
| B1A01:01 | Speaker #1: General Electrical Failure | GO to Pinpoint Test L . |
| B1A01:11 | Speaker #1: Circuit Short To Ground | GO to Pinpoint Test L . |
| B1A01:12 | Speaker #1: Circuit Short To Battery | GO to Pinpoint Test L . |
| B1A01:13 | Speaker #1: Circuit Open | GO to Pinpoint Test L . |
| B1A02:01 | Speaker #2: General Electrical Failure | GO to Pinpoint Test F . |
| B1A02:11 | Speaker #2: Circuit Short To Ground | GO to Pinpoint Test F . |
| B1A02:12 | Speaker #2: Circuit Short To Battery | GO to Pinpoint Test F . |
| B1A02:13 | Speaker #2: Circuit Open | GO to Pinpoint Test F . |
| B1A03:01 | Speaker #3: General Electrical Failure | GO to Pinpoint Test H . |
| B1A03:11 | Speaker #3: Circuit Short To Ground | GO to Pinpoint Test H . |
| B1A03:12 | Speaker #3: Circuit Short To Battery | GO to Pinpoint Test H . |
| B1A03:13 | Speaker #3: Circuit Open | GO to Pinpoint Test H . |
| B1A04:01 | Speaker #4: General Electrical Failure | GO to Pinpoint Test J . |
| B1A04:11 | Speaker #4: Circuit Short To Ground | GO to Pinpoint Test J . |
| B1A04:12 | Speaker #4: Circuit Short To Battery | GO to Pinpoint Test J . |
| B1A04:13 | Speaker #4: Circuit Open | GO to Pinpoint Test J . |
| B1A05:01 | Speaker #5: General Electrical Failure | GO to Pinpoint Test M . |
| B1A05:11 | Speaker #5: Circuit Short To Ground | GO to Pinpoint Test M . |
| B1A05:12 | Speaker #5: Circuit Short To Battery | GO to Pinpoint Test M . |
| B1A05:13 | Speaker #5: Circuit Open | GO to Pinpoint Test M . |
| B1A06:01 | Speaker #6: General Electrical Failure | GO to Pinpoint Test G . |
| B1A06:11 | Speaker #6: Circuit Short To Ground | GO to Pinpoint Test G . |
| B1A06:12 | Speaker #6: Circuit Short To Battery | GO to Pinpoint Test G . |
| B1A06:13 | Speaker #6: Circuit Open | GO to Pinpoint Test G . |
| B1A07:01 | Speaker #7: General Electrical Failure | GO to Pinpoint Test I . |
| B1A07:11 | Speaker #7: Circuit Short To Ground | GO to Pinpoint Test I . |
| B1A07:12 | Speaker #7: Circuit Short To Battery | GO to Pinpoint Test I . |
| B1A07:13 | Speaker #7: Circuit Open | GO to Pinpoint Test I . |
| B1A08:01 | Speaker #8: General Electrical Failure | GO to Pinpoint Test K . |
| B1A08:11 | Speaker #8: Circuit Short To Ground | GO to Pinpoint Test K . |
| B1A08:12 | Speaker #8: Circuit Short To Battery | GO to Pinpoint Test K . |
| B1A08:13 | Speaker #8: Circuit Open | GO to Pinpoint Test K . |
| B1A09:11 | Speaker #9: Circuit Short To Ground | GO to Pinpoint Test N . |
| B1A09:12 | Speaker #9: Circuit Short To Battery | GO to Pinpoint Test N . |
| B1A09:13 | Speaker #9: Circuit Open | GO to Pinpoint Test N . |
| B1A10:11 | Speaker #10: Circuit Short To Ground | GO to Pinpoint Test N . |
| B1A10:12 | Speaker #10: Circuit Short To Battery | GO to Pinpoint Test N . |
| B1A10:13 | Speaker #10: Circuit Open | GO to Pinpoint Test N . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Subject Type Information | GO to Pinpoint Test AI . |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to Pinpoint Test AM . |
| U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test AP . |
| U0256:00 | Lost Communication With Front Controls Interface Module "A": No Sub Type Information | GO to Pinpoint Test AQ . |
| U0257:00 | Lost Communication With Front Controls/Display Interface Module: No Sub Type Information | GO to Pinpoint Test AR . |
| U0423:00 | Invalid Data Received from Instrument Panel Cluster Control Module: No Sub Type Information | REFER to Instrumentation, Message Center and Warning Chimes to RETRIEVE and FOLLOW DTCs present in the IPC. If no DTCs are present in the IPC, DIAGNOSE the observable symptom. |
| U2014:01 | Control Module Hardware: General Electrical Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:01 is still present, INSTALL a new audio DSP module. Refer to Audio Digital Signal Processing (DSP) Module . |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | This DTC sets due to incomplete or incorrect PMI procedures. CHECK the vehicle service history for recent service actions related to the audio DSP module. If there have been recent service actions with the audio DSP module, INSTALL as-built data from PTS, following the diagnostic scan tool instructions under Module Programming>As-Built. If there have been no recent service actions, INSTALL a new audio DSP module to correct the failure to retain configuration data. REFER to Audio Digital Signal Processing (DSP) Module . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | This DTC sets due to incomplete or incorrect PMI procedures. CHECK the vehicle service history for recent service actions related to the audio DSP module. If there have been recent service actions with the audio DSP module, INSTALL as-built data from PTS, following the diagnostic scan tool instructions under Module Programming>As-Built. If there have been no recent service actions, INSTALL a new audio DSP module to correct the failure to retain configuration data. REFER to Audio Digital Signal Processing (DSP) Module . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | This DTC sets due to incomplete or incorrect PMI procedures. CHECK the vehicle service history for recent service actions related to the audio DSP module. If there have been recent service actions with the audio DSP module, INSTALL as-built data from PTS, following the diagnostic scan tool instructions under Module Programming>As-Built. If there have been no recent service actions, INSTALL a new audio DSP module to correct the failure to retain configuration data. REFER to Audio Digital Signal Processing (DSP) Module . |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the DTC. REPEAT the self-test. If DTC U3000:41 is retrieved again, INSTALL a new audio DSP module. Refer to Audio Digital Signal Processing (DSP) Module . |
| U3000:42 | Control Module: General Memory Failure | CLEAR the DTC. REPEAT the self-test. If DTC U3000:42 is retrieved again, INSTALL a new audio DSP module. Refer to Audio Digital Signal Processing (DSP) Module . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AS . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AT . |