Common Specifications & Procedures
AVIATOR (HYBRID/EXCEPT HYBRID) COMMON SPECIFICATIONS & PROCEDURES
| System | Specification/Procedure | ||||
|---|---|---|---|---|---|
| Air Conditioning | |||||
| Service | SPECIFICATIONS | ||||
| Torque | Refer to the appropriate component in REMOVAL AND INSTALLATION | ||||
| Axle Nut/Hub Nut | Front Wheel Bearing And Wheel Hub Stage 1: 66 lb.ft (90 Nm) Stage 2: 45° |
||||
| Battery | |||||
| Specifications | Specifications | ||||
| Brakes | |||||
| Bleeding Sequence | Brake System Pressure Bleeding | ||||
| Front Disc Brakes w/Torque | Refer to appropriate component in Removal And Installation | ||||
| Rear Disc Brakes w/Torque | Refer to appropriate component in Removal And Installation | ||||
| Charging | |||||
| Generator w/Torque | |||||
| For removal and installation, refer to Removal And Installation | Generator Bolt 35 lb.ft (47.5 Nm) Generator Nut: 35 lb.ft (47.5 Nm) Generator Stud 71 lb.in (8 Nm) |
||||
| Drive Belts | |||||
| Adjustment | Accessory Drive | ||||
| Belt Routing | Accessory Drive - Component Location . | ||||
| Engine Cooling | |||||
| General Service Specifications | Specifications | ||||
| Radiator Cap Pressure | 145 kPa (21 psi) | ||||
| Thermostat R & I | Thermostat . | ||||
| Water Pump R & I | Coolant Pump | ||||
| Engine Mechanical | |||||
| Compression | For Except Hybrid, refer to: Specifications For Hybrid, refer to: Specifications |
||||
| Oil pressure (hot @ 1, 500 rpm) | 16.0 -24.7 psi (110 -170 kPa) | ||||
| Overhaul | For Except Hybrid, refer to: Specifications For Hybrid, refer to: Specifications |
||||
| Torque | For Except Hybrid, refer to: Removal And Installation For Hybrid, refer to: Removal And Installation |
||||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||||
| Flywheel/Flex Plate Torque | |||||
| For Except Hybrid tightening sequence, refer to: Flexplate For Hybrid tightening sequence, refer to: Flywheel |
Torque: 59 lb.ft (80 Nm) | ||||
| Fuel System | |||||
| Fuel Filter Location | Located in fuel tank as part of the fuel pump module. | ||||
| Fuel Filter R & I | For Except Hybrid, refer to: Fuel Pump And Sender Unit For Hybrid, refer to: Fuel Pump And Sender Unit |
||||
| Pressure Release Procedure | For Except Hybrid, refer to: Fuel System Pressure Release For Hybrid, refer to: Fuel System Pressure Release |
||||
| Fuel Pressure Test Procedure | For Except Hybrid, refer to: Fuel System Pressure Check For Hybrid, refer to: Fuel System Pressure Check |
||||
| Ignition | |||||
| Spark Plug | CYFS 12Y PT | ||||
| Torque: | 133 lb.in (15 Nm) | ||||
| Firing Order & Cylinder Identification | 1-3-4-2 |
||||
| Ignition Wires (Routing) | Engine has coil-on-plug ignition. | ||||
| Starting | |||||
| Starter | Specifications | ||||
| Torque | |||||
| For removal and installation, refer to Starter Motor . | Starter Motor Stud bolts: 35 lb.ft (47.5 Nm) | ||||
| Wheel Alignment | |||||
| Adjustment Specifications | Specifications | ||||
| Torque | Refer to the appropriate procedure in General Procedures | ||||
| Wheel & Tire | |||||
| Wheel Lug Nut Torque | For tightening sequence, refer to Wheel And Tire
. 150 lb.ft (204 Nm) |
||||