| PCM |
P0298:00 |
Engine Oil Overtemperature Condition: No Sub Type Information |
GO to Pinpoint Test DY |
| PCM |
P0602:00 |
Powertrain Control Module Programming Error: No Sub Type Information |
GO to Pinpoint Test QA |
| PCM |
P0604:00 |
Internal Control Module Random Access Memory (RAM) Error: No Sub Type Information |
GO to Pinpoint Test QA |
| PCM |
P0605:00 |
Internal Control Module Read Only Memory (ROM) Error: No Sub Type Information |
GO to Pinpoint Test QA |
| PCM |
P0606:00 |
Control Module Processor: No Sub Type Information |
GO to Pinpoint Test QA |
| PCM |
P0607:00 |
Control Module Performance: No Sub Type Information |
GO to Pinpoint Test QA |
| PCM |
P0610:00 |
Control Module Vehicle Options Error: No Sub Type Information |
GO to Pinpoint Test QA |
| PCM |
P061E:00 |
Internal Control Module Brake Signal Performance: No Sub Type Information |
GO to Pinpoint Test QA |
| PCM |
P062F:00 |
Internal Control Module EEPROM Error: No Sub Type Information |
GO to Pinpoint Test QA |
| PCM |
P0630:00 |
VIN Not Programmed or Incompatible - ECM/PCM: No Sub Type Information |
GO to Pinpoint Test QA |
| PCM |
P064F:00 |
Unauthorized Software/Calibration Detected: No Sub Type Information |
GO to Pinpoint Test QA |
| PCM |
P06DA:00 |
Engine Oil Pressure Control Circuit/Open: No Sub Type Information |
GO to Pinpoint Test U |
| PCM |
P06DB:00 |
Engine Oil Pressure Control Circuit Low: No Sub Type Information |
GO to Pinpoint Test U |
| PCM |
P06DC:00 |
Engine Oil Pressure Control Circuit High: No Sub Type Information |
GO to Pinpoint Test U |
| PCM |
P06DD:00 |
Engine Oil Pressure Control Circuit Performance/Stuck Off: No Sub Type Information |
GO to Pinpoint Test U |
| PCM |
P1001:00 |
KOER Not Able to Complete, KOER Aborted: No Sub Type Information |
GO to Pinpoint Test V |
| PCM |
P160A:00 |
Control Module Vehicle Options Reconfiguration Error: No Sub Type Information |
GO to Pinpoint Test QA |
| PCM |
P161C:00 |
Automatic Engine Shutdown Mismatch with Vehicle Configuration: No Sub Type Information |
GO to Pinpoint Test QA |
| PCM |
P1635:00 |
Tire/Axle Out of Acceptable Range: No Sub Type Information |
GO to Pinpoint Test QA |
| PCM |
P1639:00 |
Vehicle ID Block Corrupted, Not Programmed: No Sub Type Information |
GO to Pinpoint Test QA |
| PCM |
P1935:00 |
Brake Switch/Sensor Signal: No Sub Type Information |
GO to Pinpoint Test QA |
| PCM |
P264F:00 |
Engine Serial Number Not Programmed or Incompatible: No Sub Type Information |
GO to Pinpoint Test QA |
| PCM |
U0103:00 |
Lost Communication With Gear Shift Control Module A: No Sub Type Information |
GO to Pinpoint Test A |
| PCM |
U0104:00 |
Lost Communication With Cruise Control Module: No Sub Type Information |
GO to Pinpoint Test B |
| PCM |
U0121:00 |
Lost Communication With Anti-Lock Brake System (ABS) Control Module 'A': No Sub Type Information |
GO to Pinpoint Test C |
| PCM |
U0126:00 |
Lost Communication With Steering Angle Sensor Module: No Sub Type Information |
GO to Pinpoint Test D |
| PCM |
U0131:00 |
Lost Communication With Power Steering Control Module 'A': No Sub Type Information |
GO to Pinpoint Test E |
| PCM |
U0137:00 |
Lost Communication With Trailer Brake Control Module: No Sub Type Information |
GO to Pinpoint Test F |
| PCM |
U0138:00 |
Lost Communication with All Terrain Control Module: No Sub Type Information |
GO to Pinpoint Test G |
| PCM |
U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test H |
| PCM |
U0151:00 |
Lost Communication With Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test I |
| PCM |
U0155:00 |
Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information |
GO to Pinpoint Test J |
| PCM |
U0164:00 |
Lost Communication With HVAC Control Module 'A': No Sub Type Information |
GO to Pinpoint Test K |
| PCM |
U0199:00 |
Lost Communication With 'Door Control Module A': No Sub Type Information |
GO to Pinpoint Test L |
| PCM |
U0200:00 |
Lost Communication With 'Door Control Module B': No Sub Type Information |
GO to Pinpoint Test M |
| PCM |
U0212:00 |
Lost Communication With Steering Column Control Module: No Sub Type Information |
GO to Pinpoint Test D |
| PCM |
U0230:00 |
Lost Communication With Rear Gate Module: No Sub Type Information |
GO to Pinpoint Test N |
| PCM |
U023A:00 |
Lost Communication With Image Processing Module A: No Sub Type Information |
GO to Pinpoint Test O |
| PCM |
U0252:00 |
Lost Communication With Lighting Control Module- Rear 'B': No Sub Type Information |
GO to Pinpoint Test P |
| PCM |
U0256:00 |
Lost Communication With Front Controls Interface Module 'A': No Sub Type Information |
GO to Pinpoint Test Q |
| PCM |
U0298:00 |
Lost Communication With DC/DC Converter Control Module 'A': No Sub Type Information |
GO to Pinpoint Test R |
| PCM |
U0402:00 |
Invalid Data Received from TCM: No Sub Type Information |
GO to Pinpoint Test S |
| PCM |
U0404:00 |
Invalid Data Received from Gear Shift Control Module A: No Sub Type Information |
GO to Pinpoint Test S |
| PCM |
U0405:00 |
Invalid Data Received From Cruise Control Module: No Sub Type Information |
GO to Pinpoint Test S |
| PCM |
U0415:00 |
Invalid Data Received from Anti-Lock Brake System (ABS) Control Module 'A': No Sub Type Information |
GO to Pinpoint Test S |
| PCM |
U0416:00 |
Invalid Data Received From Vehicle Dynamics Control Module: No Sub Type Information |
GO to Pinpoint Test S |
| PCM |
U0422:00 |
Invalid Data Received From Body Control Module: No Sub Type Information |
GO to Pinpoint Test S |
| PCM |
U0423:00 |
Invalid Data Received from Instrument Panel Cluster Control Module: No Sub Type Information |
GO to Pinpoint Test S |
| PCM |
U1011:00 |
Invalid Internal Control Module Monitoring Data Received from ECM/PCM: No Sub Type Information |
GO to Pinpoint Test S |
| PCM |
U1012:00 |
Invalid Internal Control Module Monitoring Data Received from Anti-Lock Brake System (ABS) Control Module: No Sub Type Information |
GO to Pinpoint Test S |
| PCM |
U1013:00 |
Invalid Internal Control Module Monitoring Data Received from TCM: No Sub Type Information |
GO to Pinpoint Test S |
| PCM |
U101E:00 |
Invalid Internal Control Module Monitoring Data Received from Gear Shift Module: No Sub Type Information |
GO to Pinpoint Test S |
| PCM |
U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test QA |
| PCM |
U2101:00 |
Control Module Configuration Incompatible: No Sub Type Information |
GO to Pinpoint Test QA |
| PCM |
U2200:00 |
Control Module Configuration Memory Corrupt: No Sub Type Information |
GO to Pinpoint Test QA |