LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Mazda >> 2000 >> MPV ES >> Repair and Diagnosis >> Transmission >> Automatic Trans >> Diagnosis >> Diagnosis & Testing >> Repair Verification Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Repair Verification Procedure

NOTE: Perform this procedure after repairing a malfunction to verify malfunction has been corrected.
  1. Connect scan tool to DLC. Turn ignition switch to ON position. Clear DTCs. Perform appropriate DTC drive cycle listed below to ensure DTC has been repaired:

    1. P0500

      Start engine and warm to 140°F (60°C) or more. Using scan tool, access TURBINE, 1GR and D SW PIDs from PID/DATA MONITOR & RECORD menu. Road test vehicle until TURBINE PID value is 1500 RPM or more, 1GR value is ON and D SW PID value is ON for 16 seconds or more. Go to step  2.

    2. P0705

      Start engine and allow to idle. Using scan tool, access RPM, D SW, S SW, L SW, R SW and TR SW PIDs from PID/DATA MONITOR & RECORD menu. Road test vehicle in each range ("P", "R", "N", "D", "2" and "1") with RPM PID value at 530 RPM or more for at least 2 minutes. Go to step  2.

    3. P0706

      Start engine and allow to idle. Using scan tool, access RPM, VS, D SW, S SW and L SW PIDs from PID/DATA MONITOR & RECORD menu. Road test vehicle in each range ("D", "2" and "1") with RPM PID value at 530 RPM or more, and VS PID value at 12 MPH for at least 2 minutes. Go to step  2.

    4. P0710

      Start engine and allow to idle. Using scan tool, access VS PID from PID/DATA MONITOR & RECORD menu. Road test vehicle with VS PID value at 12 MPH for at least 2 minutes. Go to step  2.

    5. P0711

      Ensure engine coolant temperature has decreased to 68°F (20°C) or less. Start engine and allow to idle. Using scan tool, access VS PID from PID/DATA MONITOR & RECORD menu. Road test vehicle with VS PID value at 37 MPH for more than 7 minutes. Go to step  2.

    6. P0715

      Start engine and allow to idle. Using scan tool, access VS PID from PID/DATA MONITOR & RECORD menu. Road test vehicle with VS PID value at 25 MPH for 5 seconds. Go to step  2.

    7. P0731

      Start engine. Warm engine and transaxle to normal operating temperature. Using scan tool, access VS, 1GR, TP V, D SW and O/DF LP PIDs from PID/DATA MONITOR & RECORD menu. Road test vehicle to achieve VS PID value 5-30 MPH, 1GR and D SW values ON, O/DF LP value OFF, and TP V PID value 1.1 volts or more for 15 seconds or more. Bring vehicle to a complete stop and repeat PID/DATA MONITOR & RECORD procedure 5 times. Go to step  2.

    8. P0732

      Start engine. Warm engine and transaxle to normal operating temperature. Using scan tool, access VS, 2GR, D SW and O/DF LP PIDs from PID/DATA MONITOR & RECORD menu. Road test vehicle to achieve VS PID value 6-54 MPH, 2GR and D SW values ON and O/DF LP value OFF for 15 seconds or more. Bring vehicle to a complete stop and repeat PID/DATA MONITOR & RECORD procedure 4 times. Go to step  2.

    9. P0733

      Start engine. Warm engine and transaxle to normal operating temperature. Using scan tool, access VS, 3GR, D SW, and O/DF LP PIDs from PID/DATA MONITOR & RECORD menu. Road test vehicle to achieve VS PID value 17-30 MPH, 3GR and D SW values ON and O/DF LP value OFF for 5 seconds or more. Go to step  2.

    10. P0734

      Start engine. Warm engine and transaxle to normal operating temperature. Using scan tool, access VS, 4GR, D SW, and O/DF LP PIDs from PID/DATA MONITOR & RECORD menu. Road test vehicle to achieve VS PID value 48-64 MPH, 4GR and D SW values ON and O/DF LP value OFF for 15 seconds or more. Go to step  2.

    11. P0740

      Start engine. Warm engine and transaxle to normal operating temperature. Using scan tool, access VS, 4GR, D SW, O/DF LP and TCC CON PIDs from PID/DATA MONITOR & RECORD menu. Road test vehicle to achieve VS PID value 47-64 MPH, 4GR, D SW and TCC CON values ON and O/DF LP value OFF for 15 seconds or more. Go to step  2.

    12. P0743

      Start engine. Road test vehicle, ensuring transaxle shifts smoothly through all gears and TCC engages. Go to step  2.

    13. P0745

      Start engine. Road test vehicle in first gear with gearshift lever in "D" position. Go to step  2.

    14. P0750, P0755, P0760 & P1763

      Road test vehicle, ensuring transaxle shifts smoothly through all gears and TCC engages. Go to step  2.
  2. Once DTC drive cycle is complete, bring vehicle to a gradual stop. Perform self-test on PCM and ensure serviced DTC does not repeat. If serviced DTC resets, repeat REPAIR VERIFICATION PROCEDURE  for appropriate DTC. If serviced DTC resets again, replace PCM.
scientia non olet · About LEMON Manuals