PCM Inspection Using the SST (WDS or equivalent)
NOTE:
- PIDs for the following parts are not available on this model. Go to the appropriate part inspection page.
- CMP sensor (See CAMSHAFT POSITION (CMP) SENSOR INSPECTION .)
- Main relay (See RELAY INSPECTION .)
- Connect the WDS or equivalent to the DLC-2. (See ON-BOARD DIAGNOSTIC TEST .)
- Turn the ignition switch to ON.
- Measure the value.
- If the value is not within the specification, follow the instructions in Action column.
PIP/DATA MONITOR table (Reference)
PIP/DATA MONITOR
| Parameter Name | Unit/Condition | Condition/Specification (Reference) | Inspection item | PCM terminal | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| AAT (Ambient air temperature) (2) | °C or °F | Indicates ambient air temperature | The following PIDs: IAT | - | ||||||||
| A_CREQ (A/C switch) | On/Off | A/C and fan operating: On A/C not operating: Off |
The following PIDs: RPM, TP, ECT | 5 | ||||||||
| ACCS (A/C relay) | On/Off | A/C operating: On IG SW ON: Off |
The following PIDs: RPM, TP, ECT | 47 | ||||||||
| ALTF (Generator field coil control duty value) | % | IG SW ON: 0% Idle: 0-100% Generator operating E/L ON: Duty value rises |
The following PIDs: IAT, RPM, ALTTV | 36 | ||||||||
| ALTT V (Generator output voltage) | V | IG SW ON: 0 V Idle: 14-16 V |
The following PIDs: IAT, RPM, ALTF Generator |
63 | ||||||||
| ARPMDES (Target engine speed) | RPM | Idle: Indicates target engine speed | Perform "ON-BOARD DIAGNOSTIC TEST" | - | ||||||||
| B+ (Battery positive voltage) | V | IG SW ON: B+ | Battery | 86 | ||||||||
| BARO (Barometric pressure) | Pa | IG SW ON: Indicates barometric pressure | EGR boost sensor | 37 | ||||||||
| V | Less than 400 m {1.13 ft} above sea level: 4.1-4.3 V | |||||||||||
| BARO/EGR (EGR boost sensor solenoid valve) | On/Off | Ignition switch ON: Off Idle: Off |
EGR boost sensor solenoid valve | 93 | ||||||||
| BOO (Brake switch) | On/Off | Brake pedal depressed: On Brake pedal released: Off |
Brake switch | 82 | ||||||||
| CATT11_DSD (Estimated catalytic converter temperature) | °C or °F | Indicates estimated catalytic converter temperature | The following PIDs: BARO, ECT, IAT, MAR RPM | - | ||||||||
| CATT21_DSD (Estimated catalytic converter temperature) | °C or °F | Indicates estimated catalytic converter temperature | The following PIDs: BARO, ECT, IAT, MAF, RPM | - | ||||||||
| CHRGLP (Generator warning light) | On/Off | IG SW ON: On Idle: Off |
Generator warning light | 65 | ||||||||
| COLP (Refrigerant pressure switch (medium pressure switch)) | On/Off | Refrigerant pressure is the threshold or more: On Refrigerant pressure is the threshold or less: Off |
Refrigerant pressure switch (medium pressure switch) | 30 | ||||||||
| DTCCNT (Number of DTC detected) | - | Number of DTCs stored Normal: 0 | Perform applicable DTC troubleshooting. | - | ||||||||
| ECT (Engine coolant temperature) | °C or °F | IG SW ON: Indicates engine coolant temperature | ECT sensor | 41 | ||||||||
| V | ECT 20 °C {68 °F}: 2.9-3.1 V After warm up: 0.2-1.0 V | |||||||||||
| EQ_RAT11_DSD (Theoretical air/fuel ratio coefficient to calculate target air/fuel ratio) | - | Idling after warm-up: Approx.1 | HO2S (Front, LH/RH) | - | ||||||||
| EVAPCP (Purge solenoid valve duty value) | % | IG SW ON: 0% | The following PIDs: IAT, RPM, ECT, MAF, TP, BARO, O2S11, O2S21 | 85 | ||||||||
| FAN_DUTY (Fan control signal) | % | ECT below 100 °C {212 °F}: 0% ECT above 100 °C {212 °F}: 35- 100% |
Inspect ECT sensor | 69 | ||||||||
| FLI (Fuel level) (2) | % | Fuel gauge level F: Approx. 100% Fuel gauge level E: Approx. 0% |
Perform applicable DTC troubleshooting. | - | ||||||||
| FP (Fuel pump relay) | On/Off | IG SW ON: Off Idle: On Cranking: On |
The following PID: RPM | 95 (3), 67 (4) | ||||||||
| FUELPW (Fuel injection duration) | s | IG SW ON: 0 ms Idle: 1.5-3.0 ms |
PIDs for input signals | 48, 49, 50, 74, 75, 76 | ||||||||
| FUELSYS1 (Fuel system status (RH)) | OL/CL/ OL_Drive/ OL Fault/ CL_Fault |
Idling after warm-up: CL | The following PID: MAF, IAT, ECT, RPM, TP, O2S11, O2S12, O2S21, O2S22, BARO, VSS, PSP, ALTF, ACCS, IMCC, BOO, B+ | - | ||||||||
| FUELSYS2 (Fuel system status (LH)) (3) | OL/CL/ OL_Drive/ OL_Fault/ CL_Fault |
Idling after warm -up: CL | The following PID: MAF, IAT, ECT, RPM, TP, O2S11, O2S12, O2S21, O2S22, BARO, VSS PSP, ALTF, ACCS, IMCC, BOO, B+ | - | ||||||||
| GENVDSD (Target generator voltage) | V | Ignition switch is turned to the On position: Approx. 1.0 V or less Idling (no electrical load): Approx.14 V (This is an internal calculation value and differs from the terminal voltage.) |
The following PIDs: ECT, IAT, RPM, VSS, ALTTV, VPWR Generator | - | ||||||||
| HTR11 (HO2S heater (Front, RH)) | On/Off | Approx. 15 seconds after engine start with ECT 20-30 °C {68-86 °F}: On Others alternate: On and Off |
The following PIDs: ECT, MAF | 83 | ||||||||
| HTR12 (HO2S heater (Rear, RH)) (3) | On/Off | Approx. 15 seconds after engine start with ECT 20-30 °C {68-86 °F}: On Others alternate: On and Off |
The following PIDs: ECT, MAF | 57 | ||||||||
| HTR21 (HO2S heater (Front, LH)) | On/Off | ECT above 70 °C {158 °F}: On RHO2S heater malfunctioning: Off |
The following PIDs: ECT, MAF | 84 | ||||||||
| HTR22 (HO2S heater (Rear, LH)) (2) | On/Off | ECT above 70 °C {158 °F}: On RHO2S heater malfunctioning: Off |
The following PIDs: ECT, MAF | 58 | ||||||||
| IAC (IAC valve) | % | IG SW ON: 0% Idle: 25-40% |
The following PIDs: IAT, RPM, ECT, MAF, TP, PSP, TEST | 88 | ||||||||
| IAT (Intake air | °C or °F | IG SW ON: Indicates intake air temperature | IAT sensor | 15 | ||||||||
| V | IAT 20 °C {68 °F}: 2.3-2.5 V IAT 30 °C {86 °F}: 1.8-2.0 V |
|||||||||||
| IMCC (IMCC actuator) | % | Idle: 0% Engine speed above 3,750-5,560 rpm: 100% 50% |
The following PID: RPM | 97 | ||||||||
| INGEAR (Gears are engaged.) | On/Off | P or N position: Off Others: On |
TR switch | - | ||||||||
| IVS (CTP condition) | Idle/Off Idle | Idling: Idle Other than idling: Off Idle |
The following PIDs: TP | 40 | ||||||||
| KNOCKR (Spark retard value to prevent knocking) | °(DEG) | ldle: 0° | PIDs for input signals | 3,81 | ||||||||
| LDP_EVAPCP (EVAP system leak detection pump detect incorrect purge flow) (3) | A | Indicates EVAP system leak detection pump detect incorrect purge flow | Perform applicable DTC troubleshooting. | - | ||||||||
| LDP_IDL (EVAP system leak detection pump idle current) (3) | A | Indicates EVAP system leak detection pump idle current | Perform applicable DTC troubleshooting. | - | ||||||||
| LDP_MON (EVAP system leak detection pump monitoring current) (3) | A | Indicates EVAP system leak detection pump monitoring current | Perform applicable DTC troubleshooting. | - | ||||||||
| LDP_REF (EVAP system leak detection pump reference current) (3) | A | Indicates EVAP system leak detection pump reference current | Perform applicable DTC troubleshooting. | - | ||||||||
| LDP_SLDV (EVAP system small leak detection value) (3) | A | Indicates EVAP system small leak detection value | Perform applicable DTC troubleshooting. | - | ||||||||
| LDP_VSLDV (EVAP system small leak detection value) (1) | A/s | Indicates EVAP system small leak detection value | Perform applicable DTC troubleshooting. | - | ||||||||
| LOAD (Calculated engine load) | % | Idle: 18-20% Engine speed at 2,500 rpm: 17- 19% |
Perform "ON-BOARD DIAGNOSTIC TEST" | - | ||||||||
| LONGFT1 (Current; long fuel trim (RH) adjustment) | % | Idle: -20-20% | Perform "ON-BOARD DIAGNOSTIC TEST" | - | ||||||||
| LONGFT2 (Current long fuel trim (LH) adjustment) | % | Idle: -20-20% | Perform "ON-BOARD DIAGNOSTIC TEST" | - | ||||||||
| MAF (Intake airflow amount) | g/s | ldle: 3.3-4.7 g/s Engine speed at 2,500 rpm: 12.1-15.0 g/s |
MAF sensor | 11 | ||||||||
| V | IG SW ON: 0.0-0.1 V Idle: 0.5-0.8 V |
|||||||||||
| MIL (Malfunction indicator light) | On/Off | IG SW ON: On DTC output: On No DTC output: Off |
MIL | 68 | ||||||||
| MIL_JDIS (Travelled distance since MIL illuminate) | km or mi | Indicates travelled distance since MIL illuminate Normal: 0 km {0 mi} |
The following PIDs: DTCCNT, MIL Perform applicable DTC troubleshooting. | - | ||||||||
| O2S11 (HO2S (Front, RH)) |
V | IG SW ON: 0-1.0 V Idle (After warm up): 0-1.0 V Acceleration: 0.5-1.0 V Deceleration: 0-0.5 V |
HO2S (Front, RH) | 18 | ||||||||
| O2S12 (HO2S (Rear, RH)) (3) |
V | IG SW ON: 0-1.0 V Idle (After warm up): 0-1.0 V Acceleration: 0.5-1.0 V Deceleration: 0-0.5 V |
HO2S (Rear, RH) | 44 | ||||||||
| O2S21 (HO2S (Front, LH)) |
V | IG SW ON: 0-1.0 V After warm up: 0-1.0 V Acceleration: 0.5-1.0 V Deceleration: 0-0.5 V |
HO2S (Front, LH) | 19 | ||||||||
| O2S22 (HO2S (Rear, LH)) (3) |
V | IG SW ON: 0-1.0 V After warms up: 0-1.0 V Acceleration: 0.5-1.0 V Deceleration: 0-0.5 V |
HO2S (Rear, LH) | 45 | ||||||||
| PSP (PSP switch) | High/Low | Steering wheel at straight ahead position: Low Steering wheel fully turned: High |
PSP switch | 55 | ||||||||
| RFCFLAG (Readiness Function Code) |
Learnt/Not Learnt | Idling (after running PCM adaptive memory procedure drive mode): Learnt Right after the negative battery cable is disconnected (before running PCM adaptive memory procedure drive mode): Not Learnt |
Perform DRIVE MODE 1 | - | ||||||||
| RO2FT1 (HO2S (Rear, RH) fuel trim) (3) | - | Indicates HO2S (Rear, RH) fuel trim | The following PID: O2S12 | - | ||||||||
| RO2FT2 (HO2S (Rear, LH) fuel trim) (3) | - | Indicates HO2S (Rear, LH) fuel trim | The following PID: O2S12 | - | ||||||||
| RPM (Engine speed) | RPM | Idle: Indicates engine speed | CKP sensor | 27,1 | ||||||||
| SEGRP (EGR valve (stepping motor) position) | - | IG SW ON: 0 (step) Idle: 0 (step) Cranking: 0-60 (steps) |
The following PIDs: ECT, TP | 98, 72, 73, 99 | ||||||||
| SEGRP DSD (EGR valve position desired) | % | EGR not operating: 0% EGR operating: 0-100% |
The following PID - MAF, TP, ECT, RPM, VSS | - | ||||||||
| SHRTFT1 (Short term fuel trim (RH)) | % | Idle: -20-20% | Perform "ON-BOARD DIAGNOSTIC TEST" | - | ||||||||
| SHRTFT11 (Short term fuel trim (Front, RH)) | % | Indicates short term fuel trim (Front, RH) |
Perform "ON-BOARD DIAGNOSTIC TEST" | 18 | ||||||||
| SHRTFT12(Short term fuel trim (Rear, RH)) (2) | % | Indicates short term fuel trim (Front, LH) |
Perform "ON-BOARD DIAGNOSTIC TEST" | 44 | ||||||||
| SHRTFT2 (Short term fuel trim (LH)) | % | Idle: -20-20% | Perform "ON-BOARD DIAGNOSTIC TEST" | - | ||||||||
| SHRTFT21 (Short term fuel trim (Front, LH)) | % | Indicates short term fuel trim (Rear, RH) |
Perform "ON-BOARD DIAGNOSTIC TEST" | 19 | ||||||||
| SHRTFT22 (Short term fuel trim (Rear, LH)) (3) | % | Indicates short term fuel trim (Rear, LH) | Perform "ON-BOARD DIAGNOSTIC TEST" | 45 | ||||||||
| SPARKADV (Ignition timing) | °(BTDC) | Indicates ignition timing | The following PIDs: MAF V, I AT V, RPM, TP V, ECT V, PSP SW, NL SW, CLT SW, A/C SW, TEN, CMP Perform Engine tune-up. | 52 for #1 104 for #2 102 for #3 78 for #4 103 for #5 101 for #6 |
||||||||
| test (Test mode) | On/Off | During test mode: On Other than test mode: Off |
- | - | ||||||||
| TIRESIZE (Tire revolution per mile | - | Indicates tire revolution per mile | - | - | ||||||||
| TP (TP sensor signal voltage) | V | CTP: 0.7-1.2 V WOT: 4.15-4.8 V |
TP sensor | 40 | ||||||||
| TP REL (Throttle position signal (relative value)) | % | CTP: Approx. 0% WOT: Approx. 100% |
TP sensor | 40 | ||||||||
| TP1 (Throttle position) | % | Indicates throttle position | TP sensor | 40 | ||||||||
| TPCT (TP sensor voltage at CTP) | V | CTP: 0.7-1.2 V | TP sensor | - | ||||||||
| VSS (Vehicle speed) | KPH or MPH | Vehicle running: Indicates vehicle speed | Inspect VSS | 79 | ||||||||
|
||||||||||||