LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Mazda >> 2006 >> MX-5 Miata Base >> Repair and Diagnosis >> Engine Performance >> System >> On-Board Diagnostic [Engine Control System] >> DTC P0032 >> Diagnostic Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Diagnostic Procedure

DTC P0032 DIAGNOSTIC PROCEDURE TABLE

STEP INSPECTION ACTION
1 VERIFY FREEZE FRAME DATA AND DIAGNOSTIC MONITORING TEST RESULTS HAVE BEEN RECORDED 
  • Have FREEZE FRAME DATA and DIAGNOSTIC MONITORING TEST RESULTS (HO2S heater related) been recorded?
 Yes Go to the next step.
No Record the FREEZE FRAME DATA and DIAGNOSTIC MONITORING TEST RESULTS on the repair order, then go to the next step.
2 VERIFY RELATED REPAIR INFORMATION AVAILABILITY 
  • Verify related Service Bulletins and/or on-line repair information availability.
  • Is any related repair information available?
 Yes Perform repair or diagnosis according to the available repair information.
  • If the vehicle is not repaired, go to the next step.
No Go to the next step.
3 INSPECT FRONT HO2S CONNECTOR FOR POOR CONNECTION 
  • Turn the ignition switch off.
  • Disconnect the front HO2S connector.
  • Inspect for poor connection (such as damaged/pulled-out pins, and corrosion).
  • Is there any malfunction?
 Yes Repair or replace the terminal, then go to Step 9.
No Go to the next step.
4 INSPECT FRONT HO2S HEATER POWER CIRCUIT FOR OPEN CIRCUIT OR SHORT TO GROUND 
  • Turn the ignition switch to the ON position (Engine off).
  • Measure the voltage between front HO2S terminal C (wiring harness-side) and body ground.
  • Is the voltage B+  ?
 Yes Go to the next step.
No Repair or replace the wiring harness for a possible open circuit or short to ground, then go to Step 9.
5 INSPECT FRONT HO2S HEATER CONTROL CIRCUIT FOR SHORT TO GROUND 
  • Turn the ignition switch off.
  • Inspect for continuity between front HO2S terminal D (wiring harness-side) and body ground.
  • Is there continuity?
 Yes Repair or replace the wiring harness for a possible short to ground, then go to Step 9.
No Go to the next step.
6 INSPECT FRONT HO2S HEATER  Yes Replace the front HO2S, then go to Step 9.
(See FRONT HEATED OXYGEN SENSOR (HO2S) REMOVAL/INSTALLATION .)
No Go to the next step.
7 INSPECT PCM CONNECTOR FOR POOR CONNECTION 
  • Turn the ignition switch off.
  • Disconnect the PCM connector.
  • Inspect for poor connection (such as damaged/pulled-out pins, and corrosion).
  • Is there any malfunction?
 Yes Repair or replace the terminal, then go to Step 9.
No Go to the next step.
8 INSPECT FRONT HO2S HEATER CONTROL CIRCUIT FOR OPEN CIRCUIT 
  • Turn the ignition switch off.
  • Inspect for continuity between front HO2S terminal D (wiring harness-side) and PCM terminal 2BG (wiring harness-side).
  • Is there continuity?
 Yes Go to the next step.
No Repair or replace the wiring harness for a possible open circuit, then go to the next step.
9 VERIFY TROUBLESHOOTING OF DTC P0032 COMPLETED 
  • Make sure to reconnect all disconnected connectors.
  • Clear the DTC from the PCM memory using the WDS or equivalent.
  • Perform the KOEO self-test (using WDS or equivalent) or the HO2S heater, HO2S, and TWC Repair Verification Drive Mode (not using WDS or equivalent).

    (See KOEO/KOER SELF TEST  .)

    (See OBD-II DRIVE MODE  .)

  • Is the PENDING CODE for this DTC present?
 Yes Replace the PCM, then go to the next step.
(See PCM REMOVAL/INSTALLATION .)
No Go to the next step.
10 VERIFY AFTER REPAIR PROCEDURE  Yes Go to the applicable DTC inspection.
(See DTC TABLE  .)
No DTC troubleshooting completed.
scientia non olet · About LEMON Manuals