LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Mazda >> 2011 >> 6 s Touring Plus >> Repair and Diagnosis >> Quick Lookups >> DTC Index >> Advanced Keyless Entry And Push Button Start System DTCS
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Advanced Keyless Entry And Push Button Start System DTCS

ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM DIAGNOSTIC TROUBLE CODE (DTC) LIST

DTC Detection condition Reference
M-MDS display
B100B:11 Steering lock unit ground circuit voltage less than threshold is detected for 0.2 s  , while the circuit is not active (See DTC B100B:11 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B100B:15 Steering lock unit ground circuit voltage higher than threshold is detected for 0.2 s  (See DTC B100B:15 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B100C:11 Steering lock unit power supply circuit voltage less than threshold is detected for 0.2 s  , while the circuit is active (See DTC B100C:11 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B100C:12 Steering lock unit power supply circuit voltage higher than threshold is detected for 0.2 s  , while the circuit is not active (See DTC B100C:12 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B1026:08 Keyless control module receive error ID signal from steering lock unit (See DTC B1026:08 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B1026:51
  • Steering lock unit programming error
  • Steering lock unit is not programmed
 (See DTC B1026:51 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B1026:62 Keyless control module receive mismatch signal between unlock signal and communication signal from steering lock unit (See DTC B1026:62 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B1026:71 Unable to lock steering column (See DTC B1026:71 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B1026:87 Communication error between keyless control module and steering lock unit (See DTC B1026:87 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B1026:92 Keyless control module receive position signal indicating a serious malfunction from steering lock unit (See DTC B1026:92 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B1026:96 Keyless control module receive signal of steering lock unit internal fault (See DTC B1026:96 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B102B:51 There is no record that an advanced key was programed (programming is never performed in past) (See DTC B102B:51 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B108B:23 120 s  have elapsed since push button start 1 signal was detected (See DTC B108B:23 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B108B:29 Mismatch state of push button start 1 and 2 (See DTC B108B:29 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B108C:23 120 s  have elapsed since push button start 2 signal was detected (See DTC B108C:23 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B10A5:12 Keyless beeper circuit voltage higher than threshold (2.2-6.5 V  ), while the circuit is not active (See DTC B10A5:12 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B10C1:11 Touch sensor (LF) circuit voltage less than threshold (2.2-6.5 V  ) is detected for 1 s  while the circuit is active (See DTC B10C1:11 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B10C1:12 Touch sensor (LF) circuit voltage higher than threshold (2.2-6.5 V  ) is detected for 1 s  while the circuit is not active (See DTC B10C1:12 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B10C3:11 Touch sensor (RF) circuit voltage less than threshold (2.2-6.5 V  ) is detected for 1 s  while the circuit is active (See DTC B10C3:11 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B10C3:12 Touch sensor (RF) circuit voltage higher than threshold (2.2-6.5 V  ) is detected for 1 s  while the circuit is not active (See DTC B10C3:12 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B10C6:1F Cannot receive signal correctly from keyless antenna (exterior, rear) (See DTC B10C6:1F [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B10C7:1F Cannot receive signal correctly from keyless antenna (interior, rear) (See DTC B10C7:1F [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B10C8:1F Cannot receive signal correctly from keyless antenna (interior, center) (See DTC B10C8:1F [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B10C9:1F Cannot receive signal correctly from keyless antenna (interior, front) (See DTC B10C9:1F [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B10D1:23 Detect request switch (LF) ON signal while driving (See DTC B10D1:23 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B10D3:23 Detect request switch (RF) ON signal while driving (See DTC B10D3:23 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B10E7:11 IG1 relay output circuit voltage less than threshold (2.2-6.5 V  ) is detected for 0.1 s  , while the circuit is active (See DTC B10E7:11 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B10E7:12 IG1 relay output circuit voltage higher than threshold (2.2-6.5 V  ) is detected for 0.1 s  , while the circuit is not active (See DTC B10E7:12 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B10E7:16 IG1 monitor input circuit voltage less than threshold (2.2-6.5 V  ) is detected for 1 s  , while IG1 relay output circuit is active (See DTC B10E7:16 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B10E7:17 IG1 monitor input circuit voltage higher than threshold (2.2-6.5 V  ) is detected for 1 s  , while IG1 relay output circuit is not active (See DTC B10E7:17 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B112A:11 IG2 relay output circuit voltage less than threshold (2.2-6.5 V  ) is detected for 0.1 s  , while the circuit is active (See DTC B112A:11 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B112A:12 (G2 relay output circuit voltage higher than threshold (2.2-6.5 V  ) is detected for 0.1 s  , while the circuit is not active (See DTC B112A:12 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B112A:16 IG2 monitor input circuit voltage less than threshold (2.2-6.5 V  ) is detected for 1 s  , while IG2 relay output circuit is active (See DTC B112A:16 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B112A:17 IG2 monitor input circuit voltage higher than threshold (2.2-6.5 V  ) is detected for 1 s  , while IG2 relay output circuit is not active (See DTC B112A:17 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B113E:11 Trunk lid opener switch (vehicle exterior) circuit voltage less than 1 V is detected for 1 s  , while ignition switch is ON (See DTC B113E:11 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B11FD:1F Cannot receive signal correctly from keyless antenna (exterior, LF) (See DTC B11FD:1F [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B1210:1F Cannot receive signal correctly from keyless antenna (exterior, RF) (See DTC B1210:1F [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B11E8:11 ABS driver circuit voltage less than threshold (2.2-6.5 V  ) is detected under the following conditions:
  • Ignition switch is off
  • ABS driver circuit is active
 (See DTC B11E8:11 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
B11E8:12 ABS driver circuit voltage higher than threshold (2.2-6.5 V  ) is detected under the following conditions:
  • Ignition switch is off
  • ABS driver circuit is not active
 (See DTC B11E8:12 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
C0040:29 Brake switch and brake switch2 link malfunction (See DTC C0040:29 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
P0560:16 Battery power supply circuit (+B3) voltage less than 9 V  is detected for 10 s  (See DTC P0560:16, P0560:17 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
P0560:17 Battery power supply circuit (+B3) voltage higher than 16 V  is detected for 0.5 s  , while engine is running
P0615:11 Detect that the voltage of starter monitor is lower than the specification.
(MZR 2.5) 
  • Starter monitor input circuit voltage less than 4.3 V  is detected under the following conditions:
    • IG1 relay output circuit is not active
    • Shift lever in P range (ATX)
    • Clutch is depressed (MTX)

(MZI 3.7 V6) 
  • Starter monitor input circuit voltage less than 1.1 V  is detected under the following conditions:
    • IG1 relay output circuit is not active
    • Shift lever in P range
 (See DTC P0615:11 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
P0615:12 Detect that the voltage of starter relay is higher than the specification.
  • Feedback voltage of starter relay output circuit higher than 6 V is detected under the following conditions:
    • IG1 relay output circuit is not active
    • Clutch is depressed
 (See DTC P0615:12 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
P0615:13 Detect the mismatch voltage between starter relay and starter monitor.
(MZR 2.5) 
  • Feedback voltage of starter relay output circuit less than 4.3 V  and starter monitor input circuit higher than 4.3 V  is detected under the following conditions:
    • IG1 relay output circuit is not active
    • Shift lever in P range (ATX)
    • Clutch is depressed (MTX)

(MZI 3.7 V6) 
  • Feedback voltage of starter relay output circuit less than 1.1 V  and starter monitor input circuit higher than 1.1 V  is detected under the following conditions:
    • IG1 relay output circuit is not active
    • Shift lever in P range
 (See DTC P0615:13 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
P081C:62 CAN and P range switch signals do not correspond, while ignition switch is ON (See DTC P081C:62 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
P081D:62
  • Neutral switch is detected as continuously ON in spite of vehicle speed increasing from 0 km/h {0 mph} to 10 km/h {6.2 mph} 
  • CAN and neutral switch signals do not correspond
 (See DTC P081D:62 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
P0830:23 Clutch pedal position (CPP) switch signal is detected for 600 s  (See DTC P0830:23 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
P0850:29
  • CAN and inhibitor switch signals do not correspond, while ignition is ON (engine off).
    • Starter monitor input circuit voltage less than 4.3 V  under the following conditions:
      • IG1 relay output circuit is active
      • Shift lever is D range
      • Engine is not running
 (See DTC P0850:29 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
P1708:29 Detect the mismatch between clutch switch and starter interlock switch.
  • Clutch monitor input circuit voltage higher than 4.3 V  under the following conditions:
    • IG1 relay output circuit is not active
    • Clutch is depressed
 (See DTC P1708:29 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
P1794:16 Battery power supply circuit (+B2) voltage less than 9 V  is detected for 10 s  (See DTC P1794:16, P1794:17 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
P1794:17 Battery power supply circuit (+B2) voltage higher than 16 V is detected for 0.5 s  , while engine is running
U0001:88 Keyless control module communication error (HS-CAN) (See FOREWORD [MULTIPLEX COMMUNICATION SYSTEM] .)
U0028:87 No communication with BCM (See DTC U0028:87 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
U0100:00 Communication error with PCM (See FOREWORD [MULTIPLEX COMMUNICATION SYSTEM] .)
U0121:00 Communication error with DSC HU/CM
U0401:68 Keyless control module receive engine state or engine speed data from PCM, while steering is locked (See DTC U0401:68 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
U201F:00 Communication error with keyless receiver (See DTC U201F:00 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
U201F:13 No communication with keyless receiver (See DTC U201F:13 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
U2100:00 Configuration is not completed (See DTC U2100:00 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
U3000:41 Keyless control module internal malfunction (See DTC U3000:41 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
U3000:49 Keyless control module internal malfunction (See DTC U3000:49 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
U3003:16 Battery power supply circuit (+B1) voltage 4 V-9 V  is detected for 10 s  (See DTC U3003:16, U3003:17 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
U3003:17 Battery power supply circuit (+B1) voltage higher than 16 V is detected for 0.5 s  , while engine is running
U3004:11 ACC relay output circuit voltage less than threshold (2.2-6.5 V  ) is detected for 1 s  , while the circuit is active (See DTC U3004:11 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
U3004:12 ACC relay output circuit voltage higher than threshold (2.2-6.5 V  ) is detected for 1 s  , while the circuit is not active (See DTC U3004:12 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
U3004:16 ACC monitor input circuit voltage less than threshold (2.2-6.5 V  ) is detected for 1 s  , while ACC relay output circuit is active (See DTC U3004:16 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
U3004:17 ACC monitor input circuit voltage higher than threshold (2.2-6.5 V  ) is detected for 1 s  , while ACC relay output circuit is not active (See DTC U3004:17 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM] .)
scientia non olet · About LEMON Manuals