| B108B:23 |
Push button start switch 1 circuit malfunction |
(See DTC B108B:23 [START STOP UNIT]
.) |
| B108B:24 |
Push button start switch 1 circuit malfunction |
(See DTC B108B:24 [START STOP UNIT]
.) |
| B108C:23 |
Push button start switch 2 circuit malfunction |
(See DTC B108C:23 [START STOP UNIT]
.) |
| B108C:24 |
Push button start switch 2 circuit malfunction |
(See DTC B108C:24 [START STOP UNIT]
.) |
| B10AC:13 |
Cruise control switch circuit malfunction |
(See DTC B10AC:13 [START STOP UNIT]
.) |
| B10AC:23 |
Cruise control switch circuit malfunction |
(See DTC B10AC:23 [START STOP UNIT]
.) |
| B10C6:1F |
Keyless antenna (exterior, rear) circuit malfunction |
(See DTC B10C6:1F [ADVANCED KEYLESS ENTRY SYSTEM]
.) |
| B10C7:1F |
Keyless antenna (interior, rear) circuit malfunction |
(See DTC B10C7:1F [ADVANCED KEYLESS ENTRY SYSTEM]
.) |
| B10C9:1F |
Keyless antenna (interior, center) circuit malfunction (With keyless entry system) |
(See DTC B10C9:1F [START STOP UNIT]
.) |
| Keyless antenna (interior, front) circuit malfunction (With advanced keyless entry system) |
(See DTC B10C9:1F [ADVANCED KEYLESS ENTRY SYSTEM]
.) |
| B10D1:23 |
Request switch (LF) circuit malfunction |
(See DTC B10D1:23 [ADVANCED KEYLESS ENTRY SYSTEM]
.) |
| B10D3:23 |
Request switch (RF) circuit malfunction |
(See DTC B10D3:23 [ADVANCED KEYLESS ENTRY SYSTEM]
.) |
| B10D9:87 |
Coil antenna (built into push button start) error |
(See SECURITY INDICATOR LIGHT: 11, DTC: B10D9:87/P1260:00 [IMMOBILIZER SYSTEM]
.) |
| B10DA:51 |
Communication error with PCM (data received failure) |
(See SECURITY INDICATOR LIGHT: 22, DTC: B10DA:51/P1260:00 [IMMOBILIZER SYSTEM]
.) |
| B10DA:62 |
Communication error with PCM (code mis-matched) |
(See SECURITY INDICATOR LIGHT: 23, DTC: B10DA:62/P1260:00 [IMMOBILIZER SYSTEM]
.) |
| B10E7:11 |
IG1 relay circuit malfunction |
(See DTC B10E7:11 [START STOP UNIT]
.) |
| B10E7:12 |
IG1 relay circuit malfunction |
(See DTC B10E7:12 [START STOP UNIT]
.) |
| B10E7:16 |
IG1 relay circuit malfunction |
(See DTC B10E7:16 [START STOP UNIT]
.) |
| B10E7:17 |
IG1 relay circuit malfunction |
(See DTC B10E7:17 [START STOP UNIT]
.) |
| B112A:11 |
IG2 relay circuit malfunction |
(See DTC B112A:11 [START STOP UNIT]
.) |
| B112A:12 |
IG2 relay circuit malfunction |
(See DTC B112A:12 [START STOP UNIT]
.) |
| B11FD:1F |
Keyless antenna (exterior, LF) circuit malfunction |
(See DTC B11FD:1F [ADVANCED KEYLESS ENTRY SYSTEM]
.) |
| B1210:1F |
Keyless antenna (exterior, RF) circuit malfunction |
(See DTC B1210:1F [ADVANCED KEYLESS ENTRY SYSTEM]
.) |
| B124C:56 |
Turn switch circuit malfunction |
(See DTC B124C:56 [START STOP UNIT]
.) |
| B13C3:04 |
LF control unit internal malfunction |
(See DTC B13C3:04 [ADVANCED KEYLESS ENTRY SYSTEM]
.) |
| B13C3:09 |
LF control unit malfunction |
(See DTC B13C3:09 [ADVANCED KEYLESS ENTRY SYSTEM]
.) |
| B13C3:16 |
LF control unit power supply voltage low input |
(See DTC B13C3:16 [ADVANCED KEYLESS ENTRY SYSTEM]
.) |
| B13C3:29 |
Communication error between start stop unit and LF control unit |
(See DTC B13C3:29 [ADVANCED KEYLESS ENTRY SYSTEM]
.) |
| B13D3:05 |
Remote transmitter program error |
(See SECURITY INDICATOR LIGHT: 13, DTC: B13D3:05/P1260:00 [IMMOBILIZER SYSTEM]
.) |
| B13D3:16 |
Low remote transmitter battery voltage |
(See DTC B13D3:16 [START STOP UNIT]
.) |
| B13D3:4A |
Remote transmitter assembly malfunction |
(See DTC B13D3:4A [START STOP UNIT]
.) |
| B13D3:51 |
Unregistered remote transmitter is detected |
(See SECURITY INDICATOR LIGHT: 15, DTC: B13D3:51/P1260:00 [IMMOBILIZER SYSTEM]
.) |
| B13D3:94 |
Communication error with remote transmitter |
(See SECURITY INDICATOR LIGHT: 13, DTC: B13D3:94/P1260:00 [IMMOBILIZER SYSTEM]
.) |
| B13D3:97 |
Remote transmitter registration work not completed |
(See DTC B13D3:97 [START STOP UNIT]
.) |
| B13D4:00 |
Insufficient remote transmitter programming number |
(See SECURITY INDICATOR LIGHT: 21, DTC: B13D4:00/P1260:00 [IMMOBILIZER SYSTEM]
.) |
| B1C53:13 |
Windshield wiper switch circuit malfunction |
(See DTC B1C53:13 [START STOP UNIT]
.) |
| C0040:23 |
Brake switch (No.1 signal) circuit malfunction |
(See DTC C0040:23 [START STOP UNIT]
.) |
| C0040:24 |
Brake switch (No.1 signal) circuit malfunction |
(See DTC C0040:24 [START STOP UNIT]
.) |
| C0051:95 |
Steering angle sensor assembly malfunction |
(See DTC C0051:95 [START STOP UNIT]
.) |
| C0051:2F |
Steering angle sensor signal error |
(See DTC C0051:2F [START STOP UNIT]
.) |
| C0052:14 |
Steering angle sensor A signal circuit malfunction |
(See DTC C0052:14 [START STOP UNIT]
.) |
| C0052:2F |
Steering angle sensor A signal malfunction |
(See DTC C0052:2F [START STOP UNIT]
.) |
| C0053:14 |
Steering angle sensor B signal circuit malfunction |
(See DTC C0053:14 [START STOP UNIT]
.) |
| C0053:2F |
Steering angle sensor B signal malfunction |
(See DTC C0053:2F [START STOP UNIT]
.) |
| C2003:13 |
Open circuit in steering switch |
(See DTC C2003:13 [START STOP UNIT]
.) |
| P0615:11 |
Starter relay circuit malfunction |
(See DTC P0615:11 [START STOP UNIT]
.) |
| P0615:12 |
Starter relay circuit malfunction |
(See DTC P0615:12 [START STOP UNIT]
.) |
| P0615:13 |
Starter relay circuit malfunction |
(See DTC P0615:13 [START STOP UNIT]
.) |
| P0615:16 |
Starter relay circuit malfunction |
(See DTC P0615:16 [START STOP UNIT]
.) |
| P0616:23 |
Circuit malfunction on downstream side of starter relay |
(See DTC P0616:23 [START STOP UNIT]
.) |
| P0616:24 |
Circuit malfunction on downstream side of starter relay |
(See DTC P0616:24 [START STOP UNIT]
.) |
| P0616:29 |
Downstream side of starter relay signal malfunction |
(See DTC P0616:29 [START STOP UNIT]
.) |
| P081C:23 |
NOT P position switch circuit malfunction |
(See DTC P081C:23 [START STOP UNIT]
.) |
| P081C:24 |
NOT P position switch circuit malfunction |
(See DTC P081C:24 [START STOP UNIT]
.) |
| P081D:29 |
Neutral switch error signal received |
(See DTC P081D:29 [START STOP UNIT]
.) |
| P081D:2F |
Neutral switch signal mismatch |
(See DTC P081D:2F [START STOP UNIT]
.) |
| P0830:23 |
CPP switch circuit malfunction |
(See DTC P0830:23 [START STOP UNIT]
.) |
| P0850:23 |
Transaxle range sensor circuit malfunction |
(See DTC P0850:23 [START STOP UNIT]
.) |
| P0850:24 |
Transaxle range sensor circuit malfunction |
(See DTC P0850:24 [START STOP UNIT]
.) |
| P0930:71 |
Shift-lock solenoid circuit malfunction |
(See DTC P0930:71 [START STOP UNIT]
.) |
| P1708:24 |
Starter interlock switch circuit malfunction |
(See DTC P1708:24 [START STOP UNIT]
.) |
| P1708:29 |
Starter interlock switch circuit or CPP switch circuit malfunction |
(See DTC P1708:29 [START STOP UNIT]
.) |
| P1794:16 |
Start stop unit power supply voltage (terminal 2W) low input |
(See DTC P1794:16 [START STOP UNIT]
.) |
| U0001:88 |
Module communication error (HS-CAN) |
(See DTC U0001:88/U0100:00/U0101:00/U0121:00/U0121:87/U0131:00/U0140:00/U0146:00/U0151:00/U0155:00 [START STOP UNIT]
.) |
| U0028:87 |
Communication error with rear body control module (RBCM) |
(See DTC U0028:87 [START STOP UNIT]
.) |
| U0100:00 |
Communication error with PCM |
(See DTC U0001:88/U0100:00/U0101:00/U0121:00/U0121:87/U0131:00/U0140:00/U0146:00/U0151:00/U0155:00 [START STOP UNIT]
.) |
| U0100:87 |
Communication error with PCM (no response or data mis-match) |
(See SECURITY INDICATOR LIGHT: 16, DTC: U0100:87/P1260:00 [IMMOBILIZER SYSTEM]
.) |
| U0101:00 |
Communication error with TCM |
(See DTC U0001:88/U0100:00/U0101:00/U0121:00/U0121:87/U0131:00/U0140:00/U0146:00/U0151:00/U0155:00 [START STOP UNIT]
.) |
| U0121:00 |
Communication error with DSC HU/CM |
| U0121:87 |
Communication error with DSC HU/CM |
| U0131:00 |
Communication error with EPS control module |
| U0140:00 |
Communication error with front body control module (FBCM) |
| U0146:00 |
Communication error with instrument cluster |
| U0151:00 |
Communication error with SAS control module |
| U0155:00 |
Communication error with instrument cluster |
| U0447:86 |
Error signal received from instrument cluster |
(See DTC U0447:86 [START STOP UNIT]
.) |
| U201F:11 |
Keyless receiver circuit malfunction |
(See DTC U201F:11 [START STOP UNIT]
.) |
| U201F:12 |
Keyless receiver circuit malfunction |
(See DTC U201F:12 [START STOP UNIT]
.) |
| U2100:00 |
Start stop unit configuration not completed |
(See DTC U2100:00 [START STOP UNIT]
.) |
| U2300:00 |
Configuration data not received from instrument cluster |
(See DTC U2300:00 [START STOP UNIT]
.) |
| U3000:01 |
Start stop unit internal malfunction |
(See DTC U3000:01 [START STOP UNIT]
.) |
| U3000:49 |
Start stop unit internal malfunction |
(See DTC U3000:49 [START STOP UNIT]
.) |
| U3000:96 |
Start stop unit malfunction |
(See DTC U3000:96 [START STOP UNIT]
.) |
| Start stop unit malfunction |
(See SECURITY INDICATOR LIGHT: 09, DTC: U3000:96/P1260:00 [IMMOBILIZER SYSTEM]
.) |
| U3003:16 |
Start stop unit power supply voltage (terminal 1A) low input |
(See DTC U3003:16 [START STOP UNIT]
.) |
| U3004:11 |
ACC relay circuit malfunction |
(See DTC U3004:11 [START STOP UNIT]
.) |
| U3004:12 |
ACC relay circuit malfunction |
(See DTC U3004:12 [START STOP UNIT]
.) |
| U3004:16 |
ACC relay circuit malfunction |
(See DTC U3004:16 [START STOP UNIT]
.) |
| U3004:17 |
ACC relay circuit malfunction |
(See DTC U3004:17 [START STOP UNIT]
.) |