Technical Service Bulletins

A/C Compressor
- Air Conditioning Not Cooling / Leak Test Using Fluorescent Dye (LI83.00-P-045023)
- Factory Approved Service Products (S-0473-08B)
- Remanufactured NIPPONDENSO A/C Compressors & Clutch (83/53)
- Factory Approved Service Products (00/53)
- Bear Electronic Leak Detector For R12 & R134A (83/49A)
- A/C Servicing & Recycling Regulations (83/45)
Accessories & Equipment
- Handling Lead-Free Filling Solder (60.00/22)
- Multi-Grade Metal Grease (00.45/94)
Accessories Control Systems
- Preventing Damage To Electronic Components Due To Electrostatic Discharge (54.00/238)
- Improved Diagnostic Plug Connector Housing For Star Diagnosis (58.40/112)
- Year 2000 Problem And Its Impact On Vehicle Software (00.00/68)
- Fluke Digital MULTIMETER Operation Safety Notice (58.30/105)
- Multiplex Cable (965 589 00 40 XX) Pin Breakage (DTB 33/95-2; MB-NET 620)
- Modified Cruise Control Amplifier/Reference Resistor (30/10)
- Unnecessary Replacement Of SRS Control Unit (91/23)
Air Bag, SRS
- Repair And Diagnosis Of Airbag Wiring Harnesses (91.60/195A)
- Code 9077 "VIN'S In Control Modules N2/7 And N73 Are Not Identical" Current And Stored After Installing New Ab Module (TT 01/11-J)
- Airbag Durability And Reliability (91.60/193)
- Technicians Using Star Diagnosis Systems During A Road Test (91.00/47)
- Replacement Of Airbag Control Module (DTB 16/01; MB-NET 142)
- Airbag Unit Replacement Label And Replacement Date Label Inserts (91/48A)
- The Passenger Airbag In Every USA MERCEDES-BENZ Is Installed To Comply With Federal Motor Vehicle Safety Standard 208 (DTB 14/96-2; MB-NET 273)
- Child Protection Warning Label For Airbag Models (91/28)
- Replacement Driver Airbag - Two Types (91/45)
Anti-Lock Brakes
- Removal & Installation Of ASR Hydraulic Unit (A7/3) (42/128)
- Identifying Diagnostic Procedures For Abs/Cruise Con (42/9)
- Replacement Of Safety-Related Harnesses (54/36)
- ASR II Charging Pump Modified - Info/Identification (42/119)
Anti-Theft Systems
- Warranty Key Returns (LI80.35-P-045746)
- All Outer Door Panels Being Replaced By Door Shell (72/10)
- Engine Hood Hinge Inspection Procedure (88/32)
- New Inside Door Handle Trim Plate & CHK Strap Cover (72/47)
Automatic Trans
- Compatibility Of Transmission Fluids "Gold," "Red," & "Blue" (TT 07/14-C)
- Factory Approved Service Products (S-0473-08B)
- Preliminary Approval Of The Following DEXRON III Automatic Transmission Fluids (DTB 25/95-2; MB-NET 470)
- Fixture For B-1 Piston R & I - Auto Trans.722.3/4/5 (58/84)
- Exchange Transmission - Modified Piston Seal Ring (27/96)
- Installation & Use Of Self-Tapping Fasteners (00/126)
- 722.3/4/5 - Technical Innovations & Modifications (27/95)
- 722.3/4/5 - Sealing Plugs For Vacuum Actuators (27/94)
- Factory Approved Service Products (00/53)
- 722.3/4/5 - Modified Automatic Trans. Fluid Dipstick (27/92)
- 722.5/722.3 Trans - Brake Band Piston Modified Parts (27/85A)
- Auto Trans 722.3 & 722.5: Modified Vacuum Modulator (27/90)
- Modified Vacuum Control For Modulator Pressure (27/88)
- Unnecessary Testing Of Modulating Pressure (27/89)
Auxiliary Emission Control Systems
- I/M 240 Emissions Testing On Dynamometer (14.00/31)
- Preventing Damage To Electronic Components Due To Electrostatic Discharge (54.00/238)
- Engine Performance (07.00/19)
- Replacement Emission Control Labels And VIN Tags For Vehicles (00.00/72)
- Diagnosing Activated Check Engine Light Or Stored DTC(S) (DTB 50/00; MB-NET 406)
- Improved Diagnostic Plug Connector Housing For Star Diagnosis (58.40/112)
- All Diesel Models - EGR Vacuum Transducer Leak Test (14.20/13)
- HERMANN Electronics Diagnostic Engine Analyzers (58.40/104)
- Year 2000 Problem And Its Impact On Vehicle Software (00.00/68)
- Fluke Digital MULTIMETER Operation Safety Notice (58.30/105)
- I/M 240 Emission Testing On Dynamometer (14/12A)
- Fluke Meter Approved For Standard Equipment Program (58/87A)
- Multiplex Cable (965 589 00 40 XX) Pin Breakage (DTB 33/95-2; MB-NET 620)
- Enhanced State Emission Inspection Programs (DTB 01/95-4; MB-NET 554)
- New Vacuum Transducer (14/10)
- Engine Surging At Partial Load:New Vacuum Transducer (14/7)
- Vehicle Emission Control System Tampering (00/50)
Axle Shafts
- Cleaning Axle Hubs When Installing Brake Discs (42.10/123A)
- Pulling Rear Hub With New Removal/Installation Tool (35/76)
- 2.5/2.6/3.0/3.2/4.2/5.0L Eng - Flex Disc Check (41/1C)
Blowers, Superchargers & Turbochargers
- Fluke Meter Approved For Standard Equipment Program (58/87A)
- Engine 603.970 - New Front Crankshaft Pulley Bolt (03/5)
Body Electrical
- Wiring Damage On More Than 10 Wires (LI54.18-P-072022)
- Repair And Diagnosis Of Airbag Wiring Harnesses (91.60/195A)
- Repair Of Damaged Audio/COMAND Wiring Harnesses (82.00/701)
- Wiring Harness Repair Kit (58.20/118B)
Body Interior
- Preventing Damage To Electronic Components Due To Electrostatic Discharge (54.00/238)
- Year 2000 Problem And Its Impact On Vehicle Software (00.00/68)
- Fluke Digital MULTIMETER Operation Safety Notice (58.30/105)
- Multiplex Cable (965 589 00 40 XX) Pin Breakage (DTB 33/95-2; MB-NET 620)
- Modified Cruise Control Amplifier/Reference Resistor (30/10)
- Unnecessary Replacement Of SRS Control Unit (91/23)
Brakes Control Systems
- Preventing Damage To Electronic Components Due To Electrostatic Discharge (54.00/238)
- Improved Diagnostic Plug Connector Housing For Star Diagnosis (58.40/112)
- Year 2000 Problem And Its Impact On Vehicle Software (00.00/68)
- Multiplex Cable (965 589 00 40 XX) Pin Breakage (DTB 33/95-2; MB-NET 620)
- Removal & Installation Of ASR Hydraulic Unit (A7/3) (42/128)
- Identifying Diagnostic Procedures For Abs/Cruise Con (42/9)
- Replacement Of Safety-Related Harnesses (54/36)
- ASR II Charging Pump Modified - Info/Identification (42/119)
Charging Systems
- Engine 603.970 - New Front Crankshaft Pulley Bolt (03/5)
Communication Devices
- Fm Interference Noise (Not Related To Ignition Or Alternator Noise) (LI82.60-P-065256)
- Telephone Calls Being Cut Off Or Dropped (LI82.70-P-046814)
- Aftermarket Electrical Accessories Installation (54/35)
Cooling System (Mechanical)
- Factory Approved Service Products (S-0473-08B)
- Subsequent Installation Of Engine Block Heater (20/8D)
- Fluke Meter Approved For Standard Equipment Program (58/87A)
- Low-Sulfur Diesel Fuels Concerns Addressed (00/55)
- Modified Seal For Timing Chain TENSIONER Housing (05/89)
- Use Of Fan Hub Tools (58/62)
- Modified Aneroid COMPENSATOR (ALDA) (07.1/19)
- Water Pump Drain Hose/Shaft Seal Set For Water Pump (20/10A)
- Engine Cooling System Maintenance (20/9)
- Turbo Eng Overheat - Trailer Towing Not Recommended (31/2B)
Cruise Control Systems
- Cruise Control Inoperative (30.30/61)
- Identifying Diagnostic Procedures For Abs/Cruise Con (42/9)
- Modified Cruise Control Amplifier/Reference Resistor (30/10)
Differentials & Drive Axles
- Factory Approved Service Products (S-0473-08B)
- Factory Approved Service Products (00/53)
- 2.5/2.6/3.0/3.2/4.2/5.0L Eng - Flex Disc Check (41/1C)
Driveshaft & Universal Joints
- Humming/Howling/Droning Noise From Drivetrain (LI28.00-P-060078)
- 2.5/2.6/3.0/3.2/4.2/5.0L Eng - Flex Disc Check (41/1C)
Electronic Steering
- New Modified Rubber Mounts On Rear Axle Carrier (35/68)
Electronic Suspension
- New Modified Rubber Mounts On Rear Axle Carrier (35/68)
Engine Control Systems
- Biodiesel Information For MERCEDES-BENZ Vehicles 2014 Edition (5/20/14)
- Preventing Damage To Electronic Components Due To Electrostatic Discharge (54.00/238)
- Return Delivery Of Fuel System Parts (47.00/58)
- Check Engine Lamp Illuminated And Engine Will Not Start Or Stalls After Starting At; Low Ambient Temperatures (-15°C / 5°F) (LI47.20-P-045500)
- Factory Approved Service Products (S-0473-08B)
- Engine Performance (07.00/19)
- Diagnosing Activated Check Engine Light Or Stored DTC(S) (DTB 50/00; MB-NET 406)
- Improved Diagnostic Plug Connector Housing For Star Diagnosis (58.40/112)
- Mass Air Flow Sensors Damaged By Particles (DTB 40/99-2, MB-NET 486)
- HERMANN Electronics Diagnostic Engine Analyzers (58.40/104)
- Year 2000 Problem And Its Impact On Vehicle Software (00.00/68)
- Fluke Digital MULTIMETER Operation Safety Notice (58.30/105)
- Use Of Portable DEFUELER/REFUELER Tanker (58/99)
- Fluke Meter Approved For Standard Equipment Program (58/87A)
- Multiplex Cable (965 589 00 40 XX) Pin Breakage (DTB 33/95-2; MB-NET 620)
Entertainment Systems
- Stuck Cd Magazine Cannot Be Ejected By Performing A "Reset" Procedure (LI82.64-P-065253)
- Repair Of Damaged Audio/COMAND Wiring Harnesses (82.00/701)
- Cd Changer Skipping During Playback, Radio Not Recognizing Magazine Insertion (82.62/169B)
- Use Of Non Commercial Compact Discs In MBUSA Cd Changers And Cd Players (DTB 32/01; MB-NET 203)
- Alpine Post-Warranty Factory Direct Repair Program (82/88)
- Cellular Telephone System Diagnosis & Return Form (82/108)
- Cd Changer - Installation & Compatibility (82/97)
- BECKER Post-Warranty Factory Direct Radio Repair (82/37C)
- Liquid Damage In Post-Warranty Radios (82/68)
- BECKER Two-Piece Radio Error Codes (82/58)
- Cd Changer Installation - Procedure/Warranty Info (82/65)
- Warranty Exchange Radio/Cd Changer (82/61)
- Aftermarket Electrical Accessories Installation (54/35)
- Replacement Of Single Unit Radio With 2-Piece Radio (82/51)
- Cd-Changer-Ready Am/Fm Stereo Cassette Radios (82/48)
- Servicing Radios With Missing/Altered Serial Numbers (82/38)
Exhaust
- Humming/Howling/Droning Noise From Drivetrain (LI28.00-P-060078)
- The Care Of Chrome Tail Pipe Finishers (49.10/11)
- Fluke Meter Approved For Standard Equipment Program (58/87A)
Exterior Body Panels
- Fuel Filler Door Difficult To Open (VERSION 4)
- Introduction Of Two-Component Epoxy Body Filler (60.00/23)
- Dedicated Straightening Equipment For Collision Repair (60/04E)
- Multi-Grade Metal Grease (00.45/94)
- Approved PAINTLESS Dent Repair (PDR) (60.00/13)
- All Outer Door Panels Being Replaced By Door Shell (72/10)
- MULTISPOT M83 Resistance Spot Welder (60.00/08B)
- MULTISPOT M20 Resistance Welder (60.00/12)
- Use Of Portable DEFUELER/REFUELER Tanker (58/99)
- Refinishing Of Plastic Body Panels (98/34)
- Trunk Interior Color Change (98/30)
Exterior Lights
- Headlamps/Front Fog Lamps Leaking Or Fogged (LI82.10-P-050139)
- Correct Bulb Usage - Overheated Bulb Socket (82/75)
Frames, Subframes & Crossmembers
- Dedicated Straightening Equipment For Collision Repair (60/04E)
- Corrosion Protection Without Hexavalent Chromium VI (97.30/05)
- MULTISPOT M83 Resistance Spot Welder (60.00/08B)
- MULTISPOT M20 Resistance Welder (60.00/12)
Front Suspension
- Assembly Of Suspension Struts And Shock Absorbers (32.25/83)
- Corrosion Protection Without Hexavalent Chromium VI (97.30/05)
- Vehicle Wheel Alignment Equipment Compliance (58.30/45A)
- Vehicle Alignment Specifications Available On Software Cd (58.00/130E)
- New 3-Lug Spring Compressor (58/54A)
- Replacing Steering Idler Arm Rubber Friction Bearing (46/72)
- New Modified Rubber Mounts On Rear Axle Carrier (35/68)
Fuel System
- Biodiesel Information For MERCEDES-BENZ Vehicles 2014 Edition (5/20/14)
- Return Delivery Of Fuel System Parts (47.00/58)
- Check Engine Lamp Illuminated And Engine Will Not Start Or Stalls After Starting At; Low Ambient Temperatures (-15°C / 5°F) (LI47.20-P-045500)
- Factory Approved Service Products (S-0473-08B)
- Mass Air Flow Sensors Damaged By Particles (DTB 40/99-2, MB-NET 486)
- Use Of Portable DEFUELER/REFUELER Tanker (58/99)
- Fluke Meter Approved For Standard Equipment Program (58/87A)
- Return Of Fuel System Components To MBNA (00/41A)
Fuses & Circuit Breakers
- Wiring Damage On More Than 10 Wires (LI54.18-P-072022)
- Wiring Harness Repair Kit (58.20/118B)
- SRS Wiring Harness Repair/Ordering Procedure (91.60/37)
- Replacement Of Safety-Related Harnesses (54/36)
Gauges & Instrument Panels
- Checking Electronic Speedometers Before Replacement (54/39)
- Operation & Testing Of Low Oil Level Indicator (18/41)
General Servicing
- Bear Electronic Leak Detector For R12 & R134A (83/49A)
- A/C Servicing & Recycling Regulations (83/45)
Hazardous Waste Material
- Fluke Meter Approved For Standard Equipment Program (58/87A)
Headlights
- Headlamps/Front Fog Lamps Leaking Or Fogged (LI82.10-P-050139)
- Correct Bulb Usage - Overheated Bulb Socket (82/75)
Hoist/Jack
- Fluke Meter Approved For Standard Equipment Program (58/87A)
Horns
- Inoperative Horn - Contact Adjustment Screw Process (82/62)
HVAC Control Systems
- Air Conditioning Not Cooling / Leak Test Using Fluorescent Dye (LI83.00-P-045023)
- Factory Approved Service Products (S-0473-08B)
- Remanufactured NIPPONDENSO A/C Compressors & Clutch (83/53)
- Factory Approved Service Products (00/53)
- Bear Electronic Leak Detector For R12 & R134A (83/49A)
- A/C Servicing & Recycling Regulations (83/45)
- Installation Of Aftermarket Air Filtration System (83/46)
- A/C Performance Test (83/30)
- Modifications Of The Automatic Climate Control (83/75)
Identification
- Replacement Emission Control Labels And VIN Tags For Vehicles (00.00/72)
- Airbag Unit Replacement Label And Replacement Date Label Inserts (91/48A)
- Child Protection Warning Label For Airbag Models (91/28)
Ignition Switch/Steering Lock
- Steering Lock Removal/Installation Guidelines (46/74)
Ignition System
- Repair Kit For Glow Plug Threads In Cylinder Head (58.20/134B)
- Fluke Meter Approved For Standard Equipment Program (58/87A)
- Low-Sulfur Diesel Fuels Concerns Addressed (00/55)
- Modified Aneroid COMPENSATOR (ALDA) (07.1/19)
Infotainment
- Repair Of Damaged Audio/COMAND Wiring Harnesses (82.00/701)
- Poor Radio Reception (DTB 05/00; MB-NET 021)
Interior/Exterior Trim
- Multi-Grade Metal Grease (00.45/94)
- The Care Of Chrome Tail Pipe Finishers (49.10/11)
- Service Kit For Rectifying Squeaking, Creaking And Tearing Noises (00.45/77)
- Installation & Use Of Self-Tapping Fasteners (00/126)
- 6-Hole Wheel Covers For 15 Inch Wheels (40/127)
- High Mount Stop Light Housing Rubber Seal Available (82/59)
- Engine Hood Hinge Inspection Procedure (88/32)
- New Inside Door Handle Trim Plate & CHK Strap Cover (72/47)
Interior/Illumination Lights
- Correct Bulb Usage - Overheated Bulb Socket (82/75)
Locking Hubs
- New Modified Rubber Mounts On Rear Axle Carrier (35/68)
Lubrication System
- Factory Approved Service Products (S-0473-08B)
- Excessive Oil Consumption Complaints (18.00/13)
- Approved Oil Evacuation Equipment (58.00/118)
- Oil Extraction Equipment Explanation/Ordering Info (58/95)
- Fluke Meter Approved For Standard Equipment Program (58/87A)
- Engine Oil Level - Do Not Overfill (00/57A)
- Engines 104/119/120/603 Oil Consumption Test Sheets (18/43A)
- Low-Sulfur Diesel Fuels Concerns Addressed (00/55)
- Factory Approved Service Products (00/53)
- Modified Seal For Timing Chain TENSIONER Housing (05/89)
- Modified Aneroid COMPENSATOR (ALDA) (07.1/19)
- Crankcase Oil Baffle Replacement & Installation (01/7B)
- Water Pump Drain Hose/Shaft Seal Set For Water Pump (20/10A)
- 2.5/3.0/3.5L Eng Noise After Start - Oil Filter Ring (18/11)
- Operation & Testing Of Low Oil Level Indicator (18/41)
- Engines 601/602/603 - Engine Oil Capacity Reduced (01/21A)
Manual Steering
- Factory Approved Service Products (S-0473-08B)
- Modified Power Steering Pump Fluid Level Indication (46/75)
- Replacing Steering Idler Arm Rubber Friction Bearing (46/72)
- New Modified Rubber Mounts On Rear Axle Carrier (35/68)
Manual Trans
- Factory Approved Service Products (S-0473-08B)
- Factory Approved Service Products (00/53)
Mechanical
- Humming/Howling/Droning Noise From Drivetrain (LI28.00-P-060078)
- Engine HYDROLOCK Repairs / Diagnosis (TT 02/11-B)
- Repair Kit For Glow Plug Threads In Cylinder Head (58.20/134B)
- Factory Approved Service Products (S-0473-08B)
- Reminder - Use Of BORESCOPE Or FIBERSCOPE As Workshop Equipment (DTB 16/97-2, MB-NET 195)
- Service Information Regarding The Assessment Of Cylinder Walls Of Engines With Aluminum Alloy Crankcase (01/30)
- Special Tool Kit For Removing And Installing Valve Springs (58/91)
- Excessive Oil Consumption Complaints (18.00/13)
- Approved Oil Evacuation Equipment (58.00/118)
- Mass Air Flow Sensors Damaged By Particles (DTB 40/99-2, MB-NET 486)
- Oil Extraction Equipment Explanation/Ordering Info (58/95)
- New Timing Chain Tools For Diesel & Gasoline Engines (58/92)
- New Timing Chain With Pressed On Center Link Plate (05/95)
- Fluke Meter Approved For Standard Equipment Program (58/87A)
- Anti-Corrosion Coating For Engine Compartment (98/48)
- Installation & Use Of Self-Tapping Fasteners (00/126)
- Coding Of Crankshaft Main Bearing Shells & Tolerance (03/4A)
- Rebuilding Diesel Engine Block With Cylinder Sleeves (01/32)
- Low-Sulfur Diesel Fuels Concerns Addressed (00/55)
- Modified Seal For Timing Chain TENSIONER Housing (05/89)
- Modified Aneroid COMPENSATOR (ALDA) (07.1/19)
- Piston & Cylinder Bore Matching (03/46B)
- Crankcase Oil Baffle Replacement & Installation (01/7B)
- Water Pump Drain Hose/Shaft Seal Set For Water Pump (20/10A)
- All Engines - Installation Of Cylinder Head Bolts (01/6)
- 2.5/3.0/3.5L Eng Noise After Start - Oil Filter Ring (18/11)
- Engine 603.970 - New Front Crankshaft Pulley Bolt (03/5)
- 2.5/3.0/3.5L Eng Higher Strength Head Bolt New Specs (01/22B)
- Valve Guide Exchange - All Engines (05/4)
Mechanical - Hydraulic
- Vibration Or Noise When Braking (LI42.10-P-061801)
- Diagnosing Complaints Of Brake Pulsation (TT 06/15-O)
- Cleaning Axle Hubs When Installing Brake Discs (42.10/123A)
- Brake Lining Installation Instructions (42.10/117A)
- Brake Pad Paste Usage (42.10/110)
- Self-Locking Brake Caliper Bolt Replacement (42.10/111)
- Corrosion Of Brake Components (42.10/109)
- Factory Approved Service Products (S-0473-08B)
- Using Brake Disc Caliper/Gauge: MB Special Tool 140 589 00 19 00 (58.00/002)
- REMACHINING Brake Discs (DTB 18/96-4; MB-NET 329)
- Brake Lathe Approved For Standard Equipment Program (58/85)
- Removal & Installation Of ASR Hydraulic Unit (A7/3) (42/128)
- Revised Anti-Corrosion Coating On Brake Discs (42/127)
- Factory Approved Service Products (00/53)
- Front Brake Pads - Two Different Versions (42/13)
- ASR II Charging Pump Modified - Info/Identification (42/119)
- Correct Brake Pad Applicability Tables (42/8)
Memory Modules
- Preventing Damage To Electronic Components Due To Electrostatic Discharge (54.00/238)
Mirrors
- Repair Kit For Sliding/Pop-Up Roof Drive (77/25)
- Modified Control Cable For Sliding/Pop-Up Roof (77/21)
Paint & Coatings
- Introduction Of Two-Component Epoxy Body Filler (60.00/23)
- MBUSA Approved Refinishing Products (98.00/13V)
- Factory Approved Service Products (S-0473-08B)
- Approved PAINTLESS Dent Repair (PDR) (60.00/13)
- MBNA Approved Refinishing Products (98/13C)
- Vehicle Paint Damage Due To Environmental Fallout (98/11)
- Production Color Changes (98/35)
- Trunk Interior Color Change (98/30)
- New Paint Material "Ms Filler": MB Paint System (98/28)
- New "MB-Polish" Availability (98/27)
- Clear Coated Solid Color Paint Finishes (98/5A)
Passive Restraints
- Repair And Diagnosis Of Airbag Wiring Harnesses (91.60/195A)
- Dirty Seats (LI91.18-P-045700)
- Repairs For Noise Complaints Regarding Seats (91.00/37)
- New Modified Rubber Mounts On Rear Axle Carrier (35/68)
Rear Suspension
- Assembly Of Suspension Struts And Shock Absorbers (32.25/83)
- Repairing Self-Locking Threaded Axle Mount Connections (35.00/08)
- Corrosion Protection Without Hexavalent Chromium VI (97.30/05)
- Vehicle Alignment Specifications Available On Software Cd (58.00/130E)
- New 3-Lug Spring Compressor (58/54A)
- Pulling Rear Hub With New Removal/Installation Tool (35/76)
- Replacing Steering Idler Arm Rubber Friction Bearing (46/72)
- New Modified Rubber Mounts On Rear Axle Carrier (35/68)
Restraints Control Systems
- Repair And Diagnosis Of Airbag Wiring Harnesses (91.60/195A)
- Preventing Damage To Electronic Components Due To Electrostatic Discharge (54.00/238)
- Code 9077 "VIN'S In Control Modules N2/7 And N73 Are Not Identical" Current And Stored After Installing New Ab Module (TT 01/11-J)
- Airbag Durability And Reliability (91.60/193)
- Technicians Using Star Diagnosis Systems During A Road Test (91.00/47)
- Replacement Of Airbag Control Module (DTB 16/01; MB-NET 142)
- Improved Diagnostic Plug Connector Housing For Star Diagnosis (58.40/112)
- Year 2000 Problem And Its Impact On Vehicle Software (00.00/68)
- Fluke Digital MULTIMETER Operation Safety Notice (58.30/105)
- Multiplex Cable (965 589 00 40 XX) Pin Breakage (DTB 33/95-2; MB-NET 620)
- Modified Cruise Control Amplifier/Reference Resistor (30/10)
- Unnecessary Replacement Of SRS Control Unit (91/23)
- Replacement Driver Airbag - Two Types (91/45)
Schedule
- Inspection Service Intervals (00/44)
Seats
- Dirty Seats (LI91.18-P-045700)
- Repairs For Noise Complaints Regarding Seats (91.00/37)
- SRS Wiring Harness Repair/Ordering Procedure (91.60/37)
- New Dye For Soft Leather Seat Covers (91/21)
- Repair Kit For Sliding/Pop-Up Roof Drive (77/25)
- Modified Control Cable For Sliding/Pop-Up Roof (77/21)
Starter
- Charge Battery (54.10/255)
- New Required Replacement MIDTRONICS Battery Tester; Special Tool: 165-Exp 717 Kit (58.20/155)
- MIDTRONICS Battery Charger 165-PSC-550KIT (58.40/148)
- Upgrade Program For The MBUSA Special Tool: 900 589 09 21 00; MIDTRONICS Battery Tester (MRC 717) (58.20/146A)
- New Battery Test Procedure, Using MIDTRONICS MCR 717 Battery (58.00/124A)
- Fluke Meter Approved For Standard Equipment Program (58/87A)
- Battery Jump-Starting And Charging (54/40A)
- Battery Care - Service Information (54/38)
- Modified Aneroid COMPENSATOR (ALDA) (07.1/19)
- Unnecessary Replacement Of Alternators (15/48)
- 2.5/3.0/3.5L Eng Noise After Start - Oil Filter Ring (18/11)
Steering Column
- Steering Lock Removal/Installation Guidelines (46/74)
- New Modified Rubber Mounts On Rear Axle Carrier (35/68)
Steering Control Systems
- Preventing Damage To Electronic Components Due To Electrostatic Discharge (54.00/238)
- Factory Approved Service Products (S-0473-08B)
- Improved Diagnostic Plug Connector Housing For Star Diagnosis (58.40/112)
- Year 2000 Problem And Its Impact On Vehicle Software (00.00/68)
- Multiplex Cable (965 589 00 40 XX) Pin Breakage (DTB 33/95-2; MB-NET 620)
Steering Gear
- Factory Approved Service Products (S-0473-08B)
- Replacing Steering Gear After An Accident (46/57)
- Replacing Steering Idler Arm Rubber Friction Bearing (46/72)
- New Modified Rubber Mounts On Rear Axle Carrier (35/68)
Steering Linkage
- Vehicle Wheel Alignment Equipment Compliance (58.30/45A)
- Vehicle Alignment Specifications Available On Software Cd (58.00/130E)
- Replacing Steering Gear After An Accident (46/57)
- Pulling Rear Hub With New Removal/Installation Tool (35/76)
- Replacing Steering Idler Arm Rubber Friction Bearing (46/72)
- New Modified Rubber Mounts On Rear Axle Carrier (35/68)
Sun Roof/T-Top/Convertible Top
- Repair Kit For Sliding/Pop-Up Roof Drive (77/25)
- Modified Control Cable For Sliding/Pop-Up Roof (77/21)
- Engine Hood Hinge Inspection Procedure (88/32)
- New Inside Door Handle Trim Plate & CHK Strap Cover (72/47)
Suspension Control Systems
- Assembly Of Suspension Struts And Shock Absorbers (32.25/83)
- Preventing Damage To Electronic Components Due To Electrostatic Discharge (54.00/238)
- Improved Diagnostic Plug Connector Housing For Star Diagnosis (58.40/112)
- Year 2000 Problem And Its Impact On Vehicle Software (00.00/68)
- Multiplex Cable (965 589 00 40 XX) Pin Breakage (DTB 33/95-2; MB-NET 620)
System
- Biodiesel Information For MERCEDES-BENZ Vehicles 2014 Edition (5/20/14)
- Preventing Damage To Electronic Components Due To Electrostatic Discharge (54.00/238)
- Return Delivery Of Fuel System Parts (47.00/58)
- Check Engine Lamp Illuminated And Engine Will Not Start Or Stalls After Starting At; Low Ambient Temperatures (-15°C / 5°F) (LI47.20-P-045500)
- Factory Approved Service Products (S-0473-08B)
- Engine Performance (07.00/19)
- Replacement Emission Control Labels And VIN Tags For Vehicles (00.00/72)
- Diagnosing Activated Check Engine Light Or Stored DTC(S) (DTB 50/00; MB-NET 406)
- Improved Diagnostic Plug Connector Housing For Star Diagnosis (58.40/112)
- Mass Air Flow Sensors Damaged By Particles (DTB 40/99-2, MB-NET 486)
- All Diesel Models - EGR Vacuum Transducer Leak Test (14.20/13)
- HERMANN Electronics Diagnostic Engine Analyzers (58.40/104)
- Year 2000 Problem And Its Impact On Vehicle Software (00.00/68)
- Fluke Digital MULTIMETER Operation Safety Notice (58.30/105)
- Use Of Portable DEFUELER/REFUELER Tanker (58/99)
- I/M 240 Emission Testing On Dynamometer (14/12A)
- Fluke Meter Approved For Standard Equipment Program (58/87A)
- Multiplex Cable (965 589 00 40 XX) Pin Breakage (DTB 33/95-2; MB-NET 620)
- Enhanced State Emission Inspection Programs (DTB 01/95-4; MB-NET 554)
- Low-Sulfur Diesel Fuels Concerns Addressed (00/55)
- Modified Seal For Timing Chain TENSIONER Housing (05/89)
- New Vacuum Transducer (14/10)
- Engine Surging At Partial Load:New Vacuum Transducer (14/7)
- Modified Aneroid COMPENSATOR (ALDA) (07.1/19)
- Vehicle Emission Control System Tampering (00/50)
- Water Pump Drain Hose/Shaft Seal Set For Water Pump (20/10A)
- Return Of Fuel System Components To MBNA (00/41A)
Towing
- Fluke Meter Approved For Standard Equipment Program (58/87A)
- Turbo Eng Overheat - Trailer Towing Not Recommended (31/2B)
Transfer Case
- Factory Approved Service Products (S-0473-08B)
- Factory Approved Service Products (00/53)
Transmission Control Systems
- Preventing Damage To Electronic Components Due To Electrostatic Discharge (54.00/238)
- Improved Diagnostic Plug Connector Housing For Star Diagnosis (58.40/112)
- Year 2000 Problem And Its Impact On Vehicle Software (00.00/68)
- Fluke Digital MULTIMETER Operation Safety Notice (58.30/105)
- Multiplex Cable (965 589 00 40 XX) Pin Breakage (DTB 33/95-2; MB-NET 620)
- Unnecessary Testing Of Modulating Pressure (27/89)
Vacuum Pumps/Lines/Tanks/Water Trap
- 2.5/3.0/3.5L Eng Noise After Start - Oil Filter Ring (18/11)
Warning Systems
- Inoperative Horn - Contact Adjustment Screw Process (82/62)
Wheel Alignment
- Vehicle Wheel Alignment Equipment Compliance (58.30/45A)
- Vehicle Alignment Specifications Available On Software Cd (58.00/130E)
Wheel Hubs
- Cleaning Axle Hubs When Installing Brake Discs (42.10/123A)
- Pulling Rear Hub With New Removal/Installation Tool (35/76)
Wheels & Tire System
- Cleaning Axle Hubs When Installing Brake Discs (42.10/123A)
- Checking Components For Bolted Wheel Connection (40.10/72)
- Corrosion Of Brake Components (42.10/109)
- Approved Alkaline MB Wheel Cleaner For Light Alloy Disk Wheel (40.10/66)
- Nitrogen Use In Tire Inflation (40.10/60)
- Chrome Plating Of MERCEDES-BENZ Light Alloy Wheels (40/18)
- MICHELIN Pilot Sport A/S Tires (40.10/43A)
- New & Updated Wheel Balancer Flange Plate & Centering Adapters (58/82A)
- Tires - Proper Maintenance And Inspection (40.10/36)
- Storage Of Vehicles Equipped With High Performance Tires (40.10/34)
- Factory-Approved Summer/All-Season/Winter Tires (40/20M)
- Drivetrain Noise & Vibration (41/18)
- Pulling Rear Hub With New Removal/Installation Tool (35/76)
- 6-Hole Wheel Covers For 15 Inch Wheels (40/127)
- Removal Tool For Adhesive Wheel Balance Weights (58/50)
- Aerosol Tire Inflator/Sealer Flammability Hazard (40/16)
- Tire Damage Caused By Pressure Washer (40/99)
- Factory Approved Winter Tires Reference Chart (40/15)
Window Motors & Regulators
- Introduction Of Improved Single-Component Windshield/Window Bonding System (67.10/27)
- New Window Glazing One-Component Adhesive Repair Kit (67.00/25)
- Damage To Laminated Glass Due To Chips Or Cracks (67/02)
- Poor Radio Reception (DTB 05/00; MB-NET 021)
- New MB Windshield Washer Concentrate (82.35/113A)
- Repair Kit For Sliding/Pop-Up Roof Drive (77/25)
- Modified Control Cable For Sliding/Pop-Up Roof (77/21)
- Engine Hood Hinge Inspection Procedure (88/32)
- New Inside Door Handle Trim Plate & CHK Strap Cover (72/47)
Wiper/Washer Systems
- Windshield Washer System: Maintaining Wiping Quality And Controlling Noise (82.35/621A)
- Factory Approved Service Products (S-0473-08B)
- New MB Windshield Washer Concentrate To Improve Windshield Cleaning (DTB 23/98-2; MB-NET 478)
- Resolving Windshield Wiper Smearing Complaints (82/67)
Wiring System (Data Link Connectors, Pwr Dist., Grnd Dist.)
- Repair And Diagnosis Of Airbag Wiring Harnesses (91.60/195A)
- Repair Of Damaged Audio/COMAND Wiring Harnesses (82.00/701)
- Wiring Harness Repair Kit (58.20/118B)
- SRS Wiring Harness Repair/Ordering Procedure (91.60/37)
- Replacement Of Safety-Related Harnesses (54/36)