ME2.1 ENGINE 104 (description only)
ME2.1 Engine 104
| DTC | SAE nomenclature | Explanation | |
|---|---|---|---|
| P0100 | - | MAF circuit malfunction | Hot film MAF sensor(B2/5) |
| P0105 | - | MAP circuit malfunction | Pressure sensor (B28) (only) |
| P0110 | - | IAT circuit malfunction | IAT sensor (in Hotfilm MAF sensor B2/5) |
| P0115 | - | ECT circuit malfunction | ECT sensor (B11/4) |
| P0120 | - | Throttle position circuit malfunction | Actual value potentiometer in EA/CC/ISC actuator (M16/1) |
| P0130 | - | O2S 1 circuit malfunction | A. O2S 1 (before TWC) (G3/2) B. O2S 1 (before TWC) (G3/2) Voltage increase insufficient |
| P0133 | - | O2S 1 circuit slow response | A O2S 1 (before TWC) (G3/2), Ageing correction value exceeded. B O2S 1 (before TWC) (G3/2), Ageing time period too long. |
| P0135 | - | O2S 1 heater circuit malfunction | O2S 1 heater (before TWC) (G3/2) |
| P0136 | - | O2S 2 circuit malfunction | O2S 2 (after TWC) (G3/1) (only) |
| P0141 | - | O2S 2 heater circuit malfunction | Right O2S 2 heater (after TWC) (G3/1) |
| P0170 | - | Fuel trim malfunction | A Self adaptation of fuel mixture ""partial load"" at limit from engine control module (N3/10). B Self adaptation of fuel mixture ""CTP"" at limit from engine control module (N3/10). |
| P0201 | - | Injector circuit malfunction- cyl. 1 | Injector (Y62y1) -cylinder 1 |
| P0202 | - | Injector circuit malfunction- cyl. 2 | Injector (Y62y2) -cylinder 2 |
| P0203 | - | Injector circuit malfunction- cyl. 3 | Injector (Y62y3) -cylinder 3 |
| P0204 | - | Injector circuit malfunction- cyl. 4 | Injector (Y62y4) -cylinder 4 |
| P0205 | - | Injector circuit malfunction- cyl. 5 | Injector (Y62y5) -cylinder 5 |
| P0206 | - | Injector circuit malfunction- cyl. 6 | Injector (Y62y6) -cylinder 6 |
| P0300 | - | Random misfire detected | A Random misfire B Random misfire, TWC damaging |
| P0301 | - | Cylinder 1 misfire detected | A Cylinder 1 misfire B Cylinder 1 misfire, TWC damaging |
| P0302 | - | Cylinder 2 misfire detected | A Cylinder 2 misfire B Cylinder 2 misfire, TWC damaging |
| P0303 | - | Cylinder 3 misfire detected | A Cylinder 3 misfire B Cylinder 3 misfire, TWC damaging |
| P0304 | - | Cylinder 4 misfire detected | A Cylinder 4 misfire B Cylinder 4 misfire, TWC damaging |
| P0305 | - | Cylinder 5 misfire detected | A Cylinder 5 misfire B Cylinder 5 misfire, TWC damaging |
| P0306 | - | Cylinder 6 misfire detected | A Cylinder 6 misfire B Cylinder 6 misfire, TWC damaging |
| P0325 | - | KS 1 circuit malfunction | Front KS 1 (A16) |
| P0330 | - | KS 2 circuit malfunction | Rear KS 2 (A16) |
| P0335 | - | CKP sensor circuit malfunction | CKP sensor (L5) |
| P0341 | - | CMP sensor circuit range/performance | Camshaft Hall-effect sensor (B6/1) |
| P0370 | - | Angle deviation between camshaft and crankshaft | Angle deviation between camshaft and crankshaft |
| P0410 | Only USA | Air injection system malfunction | AIR system malfunction (logic chain) |
| P0422 | - | TWC efficiency below threshold | TWC efficiency below threshold |
| P0440 | Only USA Models 140/210 Model 129 as of 09/97 | EVAP system malfunction | EVAP malfunction (logic chain) |
| P0441 | - | EVAP system incorrect purge flow | EVAP not functioning |
| P0442 | Only USA Mod. 140/210 Mod. 129 as of 09/97 | EVAP system leak detected (small leak) | EVAP system, small leak |
| P0443 | - | EVAP system purge control valve circuit malfunction | Purge control valve(Y58/1) |
| P0446 | Only USA Mod. 140/210 Mod. 129 as of 09/97 | EVAP system vent control malfunction | A. Activated charcoal canister shut-off valve (Y58/4) B. End stage activated charcoal canister shut-off valve (Y58/4) |
| P0450 | Only USA Mod. 140/210 Mod. 129 as of 09/97 Mod. 129 up to 08/97 Mod. 202 | EVAP system pressure sensor malfunction | A. Fuel tank pressure sensor (B4/3) electrical fault B. Fuel tank pressure sensor (B4/3) electrical fluctuations Purge monitoring pressure sensor (B4/4) |
| P0455 | Only USA Mod. 140/210 Mod. 129 as of 09/97 | EVAP system leak detected (large leak) | EVAP system, large leak Fuel tank pressure sensor (B4/3) |
| P0460 | - | Fuel level sensor circuit | - |
| P0500 | - | VSS sensor malfunction | A VSS left front B VSS left rear |
| P0507 | - | ISC RPM | Idle control system |
| P0560 | - | System voltage malfunction | Voltage supply to engine control module (N3/10) |
| P0565 | - | Cruise control switch | CC switch (S40) |
| P0600 | - | Serial communication link malfunction | CAN bus from ESP/SPS control module (N47-5) |
| P0604 | - | Internal control module random Access memory (RAM) error | A Engine control module (N3/10) B Engine control module (N3/10) |
| P0605 | - | Internal control module read only memory (ROM) error | Engine control module(N3/10) |
| P0700 | - | Transmission control system malfunction | Read DTC memory of transmission control module |
| P0702 | - | Transmission control system electrical | Read DTC memory of transmission control module |
| P0715 | - | Input/turbine speed sensor circuit malfunction | Read DTC memory of transmission control module |
| P0720 | - | Output speed sensor circuit malfunction | Read DTC memory of transmission control module |
| P0730 | - | Incorrect gear ratio | Read DTC memory of transmission control module |
| P0740 | - | Torque converter clutch circuit malfunction | Read DTC memory of transmission control module |
| P0743 | - | Torque converter clutch circuit electrical | Read DTC memory of transmission control module |
| P0748 | - | Pressure control solenoid electrical | Read DTC memory of transmission control module |
| P0753 | - | Shift solenoid A electrical | Read DTC memory of transmission control module |
| P0758 | - | Shift solenoid B electrical | Read DTC memory of transmission control module |
| P0763 | - | Shift solenoid C electrical | Read DTC memory of transmission control module |
| P0802 | - | Resonance intake manifold switchover valve | Resonance intake manifold switchover valve (Y22/6) |
| P0809 | - | Angle deviation between camshaft and crankshaft | Angle deviation between camshaft and crankshaft |
| P0811 | - | CAN from electronic ignition lock | CAN from electronic ignition lock |
| P1163 | - | Oil level switch | Oil level switch (S43) |
| P1182 | Model 202.028 only | Starter relay | Starter relay module in passenger-side fuse and relay module box (K40/4) |
| P1186 | - | Fuel safety shut-off recognized | EA/CC/ISC actuator(M16/1) |
| P1225 | - | Resonance intake manifold switchover valve | Resonance intake manifold switchover valve (Y22/6) |
| P1386 | - | Knock sensor control from ECM (N3/10) at end stop | Knock sensor regulation from engine control module (N3/10) at end stop |
| P1420 | Only USA | AIR pump switchover valve | AIR pump switchover valve (Y32) |
| P1453 | Only USA | AIR relay module | AIR relay module (K17), relay module (K40) or passenger-side fuse and relay module box (K40/4) |
| P1491 | - | - | Refrigerant pressure in A/C system too high |
| P1519 | - | Adjustable camshaft timing solenoid | Adjustable camshaft timing solenoid (Y49) (logic chain) |
| P1525 | - | Adjustable camshaft timing solenoid | Adjustable camshaft timing solenoid (Y49) |
| P1542 | - | Pedal value sensor | Pedal value sensor(B37) |
| P1570 | - | CAN signal from DAS control module to engine control module | A. Start attempted with ""locked"" DAS B. CAN signal from DAS control module (N54/1) to engine control module (N3/10) interrupted. C. Engine control module (ME-SFI) and DAS control module are not compatible. |
| P1580 | - | EA/CC/ISC actuator | EA/CC/ISC actuator(M16/1) |
| P1584 | - | Stop lamp switch | Stop lamp switch (S9/1) |
| P1603 | - | CAN signal from EIS | CAN failure |
| P1605 | - | - | Poor road/traction condition recognition signal (via comparison of VSS RPM signals) |
| P1642 | - | - | Engine control module incorrectly coded (coded for MT, vehicle has AT) |
| P1643 | - | - | Engine control module incorrectly coded (coded for MT, vehicle has AT) or No CAN transmission from transmission control module (N15/3) |
| P1644 | - | - | Transmission version can not be checked due to low voltage at transmission control module (N15/3) |
| P1747 | - | CAN signal from ETC | A. CAN failure: Transmission protection malfunction from transmission control module (N15/3) B. CAN failure: Instrument cluster |