Automatic Transmission - 117 Chassis
- General Information
- Basic Knowledge
- Testing & Repair
- Check oil level in automatic transmission and correct if necessary. - AR27.00-P-0100NKB
- Remove/install oil pump - AR27.10-P-0400NKB
- Remove/install automatic transmission - AR27.10-P-0502NKB
- Disassemble, assemble transmission - AR27.10-P-0510NKB
- Remove/install oil filler pipe for automatic transmission - AR27.10-P-7010NKB
- Remove/install automatic transmission oil pan - AR27.10-P-7030NKB
- Remove/install electrohydraulic controller unit (transmission installed) - AR27.19-P-0200NKB
- Remove/install control solenoid valves of electric controller unit - AR27.19-P-0212NKB
- Disassemble and assemble electrohydraulic controller unit - AR27.19-P-0220NKB
- Remove/install all-wheel drive control unit - AR27.19-P-1720MTA
- Remove/install dual clutch - AR27.20-P-0070NKB
- Remove/install auxiliary oil pump for automatic transmission - AR27.30-P-0651NKB
- Remove/install axle shaft radial shaft seals - AR27.40-P-0210NKB
- Disassemble/assemble transmission housing - AR27.40-P-0510NKB
- Disassemble/assemble clutch housing - AR27.40-P-0520NKB
- Remove/install power take-off - AR27.45-P-0010MTA
- Remove/install radial shaft sealing ring on output flange of power take-off - AR27.45-P-0021MTA
- Disassemble/assemble input shaft - AR27.50-P-0550NKB
- Disassemble/assemble output shaft
- Disassemble/assemble hollow shaft - AR27.50-P-0650NKB
- Remove/install differential and bearing - AR27.50-P-0771NKB
- Install dual clutch transmission gear set - AR27.50-P-0900NKB
- Remove/install transmission cooling module - AR27.55-P-1500NKB
- Remove/install transmission cooling coolant recirculation pump - AR27.55-P-7380NKB
- Remove/install electronic selector lever module (ESM) - AR27.60-P-0901AMG
- Remove/install park pawl mechanism - AR27.60-P-0950NKB
- Remove/install lift solenoid for park pawl actuator - AR27.60-P-0955NKB
- Remove/install permanent magnet of park pawl - AR27.60-P-0957NKB
- Test & Adjustment Values
- Maintenance
- Capacities & Specifications
- Torque Specifications
- Wiring Diagrams
- Special Tools
- 000 589 52 37 00 Pliers - WS27.00-P-0001C
- 126 589 12 63 00 Funnel - WS27.00-P-0029A
- 168 589 01 21 00 Dipstick - WS27.00-P-0063B
- 168 589 03 21 00 Parallel support - WS27.00-P-0076C
- 724 589 00 31 00 Assembly tool - WS27.00-P-0080B
- 724 589 00 14 00 Assembly sleeve - WS27.00-P-0081C
- 724 589 00 40 00 Assembly device - WS27.00-P-0082C
- 724 589 01 31 00 Support - WS27.00-P-0083C
- 724 589 00 15 00 Drift set - WS27.00-P-0084B
- 724 589 00 33 00 Puller - WS27.00-P-0085C
- 724 589 00 59 00 Removal and installation tool - WS27.00-P-0086C
- 724 589 00 63 00 Removal and installation tool - WS27.00-P-0087C
- 724 589 01 33 00 Puller - WS27.00-P-0088C
- 724 589 02 31 00 Support fixture - WS27.00-P-0089C
- 724 589 02 40 00 Assembly device - WS27.00-P-0090C
- 724 589 02 33 00 Puller - WS27.00-P-0138C
- 722 589 15 15 00 Drift - WS27.00-P-0164B
- 730 589 02 43 00 Drift with counterholder - WS27.00-P-3226B
- 387 589 08 15 00 Push-in drift - WS27.00-P-3366C
- 387 589 09 15 00 Insertion drift - WS27.00-P-3367C