General Orphan Data (1 Of 2)
- Main group 17
- When driving on a race track
- Frequently asked questions about surface protection
- Removing the front connecting supports
- Installing the front connecting supports
- When replacing the gasoline particulate filter: Register the gasoline particulate filter
- Grease for wheel centering
- Front Brake, MINI, F60
- Rear brakes, MINI, F60
- Intelligent battery sensor and battery
- Converting the production date
- Calculating the expiration date
- Determining the date of the next brake fluid service
- If necessary: Replacing the gas pressure springs for hood
- Remove the connecting support from the tunnel at front and rear
- Installing the connecting support on the tunnel at front and rear
- Remove the upper bulkhead cover panel
- Removing the rear bulkhead
- Remove battery carrier
- Removing the differential pressure sensor with the pressure line
- Removing the cross-member on the rear axle
- Removing the rear heat shield
- Removing the front heat shield
- Remove prop shaft
- Install prop shaft
- Installing the front heat shield
- Transmission oil for MINI manual transmission
- Transmission, general: MINI, F54, F55, F56, F57, F60, GS6-58BG/DG, GS6-59BG/DG, MANUAL
- Transmission in general
- Transmission oil for automatic transmissions GACVT16Z (CVT)/GA6F21 WA (AISIN)/GA8F22AW (AISIN)
- Transmission Case, Oil Sump
- Poisoning hazard if oil is ingested/absorbed through the skin
- Injury hazard if oil comes into contact with loops and skin
- Hang-on clutch
- Housing of rear axle differential with oil filler cap
- Rear axle carrier
- Transmission filling capacities, MINI, F54, F60, GS6-60DA, GS6X60DA/BA, MANUAL
- Engine oil consumption measurement
- Record for motor oil consumption measurement
- Suction the air conditioning
- Mounting the coolant radiator on the left and right
- Releasing the oil drain plug
- Tightening the oil drain plug
- Remove left and right wiper arm
- Removing rear windshield panel
- Disconnecting all battery ground leads
- Remove the front left and right wheels
- Remove the front left and right wheel arch cover
- Removing the washer fluid reservoir partially
- Detach steering shaft at bottom from steering gear
- Detach the cable for the ride height sensor
- Release the left and right anti-roll bar link on the anti-roll bar
- Detach rubber mount from front axle support
- Disconnect plug connections from steering gear
- Releasing the mounted parts from the front axle support
- Remove right output shaft
- Remove left output shaft
- Installing left output shaft
- Install right output shaft
- Secure mounted parts on the front axle support
- Top up the oil level in the manual transmission
- Connect connector on steering gear
- Fasten the rubber mount on the front axle support
- Securing the anti-roll bar on the left and right on the anti-roll bar link
- Fasten the cable for the ride height sensor
- Securing the steering shaft at the bottom on the steering gear
- Installing washer fluid reservoir
- Install wheel arch cover at front left and right
- Install the front left and right wheels
- Install the upper bulkhead cover panel
- Installing rear windshield panel
- Install left and right wiper arm
- Removing the mounting for the coolant radiator on the left and right
- Check engine oil level
- Evacuate and charge conditioning
- Fill and vent the high-temperature coolant circuit
- Remove front right wheel
- Removing the front right wheel arch cover
- Installing the front right wheel arch cover
- Installing the front right wheel
- Removing engine
- Removing the manual transmission from the engine
- Installing the engine on the assembly jig
- Removing the catalytic converter (engine removed)
- Blocking the engine with the special tool in TDC firing position
- Removing the cylinder head (engine removed)
- Removing the oil deflector
- Installing the engine block on the assembly jig
- Installing the oil deflector
- Installing the cylinder head (engine removed)
- Blocking the crankshaft in the TDC firing position of cylinder 1
- Disassembling all special tools
- Installing the catalytic converter (engine removed)
- Fitting the manual transmission on engine
- Removing the engine from the assembly jig
- Install engine
- Removing the automatic transmission from the engine
- If installed: Partially removing the engine ventilation line
- Removing the engine wiring harness for sensor system 1
- If installed: Partially install engine ventilation line
- Installing the automatic transmission on the engine
- Remove left and right output shaft
- Installing the output shaft on left and right
- Remove valve stem seals
- Installing valve stem seals
- Tightening the VANOS central valve of the intake adjuster
- Adjusting headlights
- Removing right suspension strut brace
- Installing the right strut brace
- Partially detaching wheel arch trim panel on left and right
- If installed: Removing the right brake ventilation duct
- If installed: Install right brake ventilation duct
- Mounting wheel arch trim panel on left and right
- Observing the hardening time of the screw locking agent on the screw plug
- Removing the engine from the double-clutch transmission (DKG)
- Remove clutch
- Install clutch
- Installing the intake adjuster
- Prepare for the installation of the clean air pipe
- Installing the engine on the double-clutch transmission (DKG)
- If installed: Removing rear underbody protection
- Disconnecting the purge air line
- Removing left output shaft at transmission end and hanging up
- Removing right output shaft at transmission end and hanging up
- Removing the left radial shaft seal on the differential (7DCT300)
- Removing the right radial shaft seal on the differential (7DCT300)
- Installing the right radial shaft seal on the differential (7DCT300)
- Installing the left radial shaft seal on the differential (7DCT300)
- Installing the left output shaft at the transmission end
- Installing right output shaft at transmission end
- Connecting purge air line
- If installed: Installing underbody protection at rear
- Removing the double-clutch transmission (DCT)
- Installing the double-clutch transmission (DCT)
- Removing the radial shaft seal on the differential (manual transmission)
- Installing the left radial shaft seal on the differential (manual transmission)
- Checking oil level in manual transmission (GS6-58BG, GS6-59DG)
- Partially removing left output shaft
- Partially removing right output shaft
- Removing intermediate shaft with support tube
- Removing holder with rubber mount
- Removing transfer box (VTG)
- Install the transfer box (VTG)
- Installing holder with rubber mount
- Installing intermediate shaft with support tube
- Partially installing the left output shaft
- Partially installing right output shaft
- Checking transfer box oil level
- Checking transmission oil (AISIN GA8G45)
- Releasing air conditioning compressor
- Fasten air conditioning compressor
- Checking the crankshaft side clearance
- Check the coefficient of friction for the crankshaft
- Removing the cylinder head
- Installing the cylinder head
- Remove front wheel arch cover
- Installing the front wheel arch cover
- Removing heat shield at upper exhaust turbocharger
- Install the heat shield on the exhaust turbocharger, top
- Checking installation position of roller cam followers
- Disassembling the cylinder head from the special tool
- Version with a servomotor of the eccentric shaft: Teaching in the end stops with the diagnostic system
- Removing heat shield at lower catalytic converter
- Installing the heat shield on the lower catalytic converter
- Remove trailing link
- Install the tension strut
- Replacement: Encode the DME control unit
- When replacing the alternator/alternator regulator: Reset generator statistical data
- Line to starter
- Remove the ignition coil of the first cylinder
- Install the ignition coil of the first cylinder
- Check the coolant level and top up if applicable
- Replacement: Adjusting the exhaust gas pressure sensor
- Fill and vent the coolant circuit
- Fuel Tank and Mounting Parts
- Removing the rear left wheel
- Installing the rear left wheel