Section 35 (Simplified Wiring System - Lancer)
WARNING: This page is about a different variant/trim than selected.
- General Description
- Special Tools
- SWS Diagnosis
- Symptom Chart
- Input Signal Chart
- Symptom Procedures
- INSPECTION PROCEDURE A-1: Communication with SWS monitor kit is not possible.
- INSPECTION PROCEDURE A-2: Communication with column switch (column-ECU) is not possible.
- INSPECTION PROCEDURE A-3: Communication with ETACS-ECU is not possible.
- INSPECTION PROCEDURE A-4: Communication with front-ECU is not possible.
- INSPECTION PROCEDURE A-5: Communication with sunroof motor assembly (sunroof-ECU) is not possible.
- Tone Alarm
- General Description The Concerning Tone Alarm
- INSPECTION PROCEDURE B-1: Tone Alarm: Ignition key reminder tone alarm function does not work normally.
- INSPECTION PROCEDURE B-2: Tone Alarm: Light reminder tone alarm function does not work normally.
- INSPECTION PROCEDURE B-3: Tone Alarm: Seat belt tone alarm function does not work normally.
- Central Door Locking System
- General Description Concerning The Central Door Locking System
- General Circuit Diagram For The Central Door Locking System
- INSPECTION PROCEDURE C-1: Central Door Locking System: The central door lock system does not work at all.
- INSPECTION PROCEDURE C-2: Central Door Locking System: Some doors do not lock or unlock.
- INSPECTION PROCEDURE C-3: Central Door Locking System: All the doors do not lock or unlock with just the door lock switch operation.
- INSPECTION PROCEDURE C-4: Central Door Locking System: All the doors do not lock or unlock with just the door lock key cylinder key operation.
- Power Windows
- General Description Concerning The Power Windows
- General Circuit Diagram For The Power Windows
- INSPECTION PROCEDURE D-1: Power Windows: Power windows do not work at all.
- INSPECTION PROCEDURE D-2: Power Windows: The power window timer function does not work normally.
- INSPECTION PROCEDURE D-3: Power Windows: Only the front door window (LH) does not work normally by operating the power window main switch.
- INSPECTION PROCEDURE D-4: Power Windows: Power windows does not work normally by operating the front passenger's and rear sub switches.
- INSPECTION PROCEDURE D-5: Power Windows: Front or rear passenger's power windows do not work at all by operating the power window main switch.
- Keyless Entry System
- General Description Concerning The Keyless Entry System
- General Circuit Diagram For The Keyless Entry System
- INSPECTION PROCEDURE E-1: Keyless Entry System: Keyless entry system does not operate.
- INSPECTION PROCEDURE E-2: Keyless Entry System: The front dome light, the turn-signal lights and the horn do not operate through the answerback function
- INSPECTION PROCEDURE E-3: Keyless Entry System: Encrypted code cannot be registered.
- Sunroof
- General Description Concerning The Sunroof
- General Circuit Diagram Regarding The Sunroof
- INSPECTION PROCEDURE F-1: Sunroof: Sunroof does not operate.
- INSPECTION PROCEDURE F-2: Sunroof: Any of the sunroof switch positions is defective.
- INSPECTION PROCEDURE F-3: Sunroof: Sunroof timer function does not work normally.
- INSPECTION PROCEDURE F-4: Sunroof: Safety mechanism does not function.
- Windshield Wiper And Washer
- General Description Concerning The Windshield Wiper And Washer
- General Circuit Diagram For The Windshield Wiper And Washer
- INSPECTION PROCEDURE G-1: Windshield Wiper and Washer: The windshield wipers do not work at all.
- INSPECTION PROCEDURE G-2: Windshield Wiper and Washer: Wipers do not work when the wiper switch is at "INT" or "MIST" position or washer switch is at "ON" position. Wipers work at low speed when wiper switch is at "LO" or "HI.
- INSPECTION PROCEDURE G-3: Windshield Wiper and Washer: Any of the windshield wiper switch positions is defective.
- INSPECTION PROCEDURE G-4: Windshield Wiper and Washer: Windshield wipers do not stop at predetermined park position.
- INSPECTION PROCEDURE G-5: Windshield Wiper and Washer: The intermittent wiper interval is not changed by operating the adjusting knob or according to the vehicle speed.
- INSPECTION PROCEDURE G-6: Windshield Wiper and Washer: Intermittent wiper interval is not changed according to vehicle speed.
- INSPECTION PROCEDURE G-7: Windshield Wiper and Washer: Windshield washer does not work.
- Seat Belt Warning Light
- Headlight And Taillight
- General Description Concerning The Headlight And Taillight
- INSPECTION PROCEDURE I-1: Headlight and Taillight: The taillights does not illuminate normally.
- INSPECTION PROCEDURE I-2: Headlight and Taillight: Headlights (low-beam) do not illuminate normally.
- INSPECTION PROCEDURE I-3: Headlight and Taillight: Headlights (high-beam) do not illuminate normally.
- INSPECTION PROCEDURE I-4: Headlight and Taillight: When passing switch is turned "on," headlights (low-beam or high-beam) do not illuminate.
- INSPECTION PROCEDURE I-5: Headlight and Taillight: Headlights do not illuminate when lighting switch is at "TAIL" and "PASSING" position, but illuminate at low-beam at "head" position, at this position, headlights cannot be changed into high beam by operating dimmer switch.
- INSPECTION PROCEDURE I-6: Headlight and Taillight: Any of taillights, the position lights or the license plate lights do not illuminate.
- INSPECTION PROCEDURE I-7: Headlight and Taillight: One of the headlights does not illuminate.
- INSPECTION PROCEDURE 1-8: Headlight and Taillight: The high-beam indicator light does not illuminate.
- INSPECTION PROCEDURE I-9: Headlight and Taillight: Headlight automatic shutdown function does not work normally.
- INSPECTION PROCEDURE 1-10: Headlight and Taillight: Headlight dimmer switch automatic resetting function does not work normally.
- INSPECTION PROCEDURE 1-11: Headlight and Taillight: Daytime running light function does not work normally.
- Fog Light
- General Description Concerning Fog Light
- INSPECTION PROCEDURE J-1: Fog Light: Fog lights do not illuminate when the fog light switch is turned on.
- INSPECTION PROCEDURE J-2: Fog Light: Fog lights do not go out when the headlights (low-beam) are turned off while the fog lights are on.
- INSPECTION PROCEDURE J-3: Fog Light: One of the fog lights does not illuminate.
- Flasher Timer
- General Description Concerning The Flasher Timer
- INSPECTION PROCEDURE K-1: Flasher Timer: Turn-signal lights do not flash when the turn-signal light switch is turned on.
- INSPECTION PROCEDURE K-2: Flasher Timer: Hazard warning lights do not flash when the hazard warning light switch is turned on.
- INSPECTION PROCEDURE K-3: Flasher Timer: The right or left turn-signal light does not illuminate.
- Interior Light
- General Description Concerning The Interior Light
- INSPECTION PROCEDURE L-1: Interior Light: Front dome light, rear dome light < vehicles without sunroof > and luggage compartment light do not illuminate or go out normally.
- INSPECTION PROCEDURE L-2: Interior Light: Front dome light, rear dome light < vehicles without sunroof > or luggage compartment light does not illuminate or go out normally.
- INSPECTION PROCEDURE L-3: Interior Light: Front dome light and rear dome light < vehicles without sunroof > dimming function does not work normally.
- INSPECTION PROCEDURE L-4: Interior Light: Interior light automatic shut-down function does not work normally.
- INSPECTION PROCEDURE L-5: Interior Light: Door ajar indicator lights do not illuminate or go out normally
- Input Signal Procedures
- INSPECTION PROCEDURE M-1: ETACS-ECU does not receive any signal from ignition switch (ACC).
- INSPECTION PROCEDURE M-2: ETACS-ECU does not receive any signal from ignition switch (IG1).
- INSPECTION PROCEDURE M-3: ETACS-ECU does not receive any signal from backup light switch < M/T >.
- INSPECTION PROCEDURE M-3: ETACS-ECU does not receive "R" position signal from transmission range switch < A/T >.
- INSPECTION PROCEDURE M-4: ETACS-ECU does not receive any signal from the driver's or front passenger's door switch.
- INSPECTION PROCEDURE M-5: Column Switch: ETACS-ECU does not receive any signal from taillight, headlight, passing light, dimmer or turn-signal light switch
- INSPECTION PROCEDURE M-6: Column switch: ETACS-ECU does not receive any signal from windshield mist, intermittent, low-speed, high-speed wiper switch or washer switch
- INSPECTION PROCEDURE M-7: Column Switch: ETACS-ECU does not receive any signal from windshield intermittent wiper interval adjusting knob.
- INSPECTION PROCEDURE M-8: Sunroof Switch: ETACS-ECU does not receive any signal from up, open or close/down switch.
- INSPECTION PROCEDURE M-9: ETACS-ECU does not receive signals from fog light switch.
- INSPECTION PROCEDURE N-1: ETACS-ECU does not receive any signal from key reminder switch.
- INSPECTION PROCEDURE N-2: ETACS-ECU does not receive any signal from hazard warning light switch.
- INSPECTION PROCEDURE N-3: ETACS-ECU does not receive any signal from seat belt buckle switch (driver's side).
- INSPECTION PROCEDURE N-4: ETACS-ECU does not receive any signal from all door switches.
- INSPECTION PROCEDURE N-5: ETACS-ECU does not receive any signal from driver's door lock key cylinder switch.
- INSPECTION PROCEDURE N-6: ETACS-ECU does not receive any signal from driver's door lock actuator switch.
- INSPECTION PROCEDURE N-7: ETACS-ECU does not receive any signal from door lock switch (incorporated in power window main switch).
- INSPECTION PROCEDURE N-8: ETACS-ECU does not receive any signal from vehicle speed sensor. < M/T >
- INSPECTION PROCEDURE N-8: ETACS-ECU does not receive vehicle speed signal < A/T >.
- INSPECTION PROCEDURE N-9: Transmitter: ETACS-ECU does not receive any signal from lock or unlock switch.
- INSPECTION PROCEDURE N-10: ETACS-ECU does not receive any interior light loaded signal.
- Check At Ecu Terminal
- On-Vehicle Service