Write Configuration Procedure

WARNING: This page is about a different car, the 2004 Nissan Titan. However, it is still accessible from the selected car via links, so may be relevant.

CAUTION: If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be detected in self-diagnosis depending on control unit which carries out CAN communication.

With ignition switch, OFF, connect CONSULT-II and CONSULT-II CONVERTER to data link connector and turn ignition switch ON.

Fig 1: Locating Data Link Connector
Courtesy of NISSAN MOTOR CO., U.S.A.
Touch "START (NISSAN BASED VHCL)".

Fig 2: CONSULT-II Display
Courtesy of NISSAN MOTOR CO., U.S.A.
Touch "BCM" on "SELECT SYSTEM" screen. If "BCM" is not indicated, go to LAN SYSTEM (INTRODUCTION) -- TITAN to check data link connector (DLC) circuit.

Fig 3: CONSULT-II Display
Courtesy of NISSAN MOTOR CO., U.S.A.
Touch "BCM" on "SELECT TEST ITEM" screen.

Fig 4: CONSULT-II Display
Courtesy of NISSAN MOTOR CO., U.S.A.
Touch "CONFIGURATION" on "SELECT DIAG MODE" screen.

Fig 5: CONSULT-II Display
Courtesy of NISSAN MOTOR CO., U.S.A.
Touch "OTHER" and "OK" on "VEHICLE SELECT" screen. For canceling, touch "CANCEL" on "VEHICLE SELECT" screen.
NOTE: Confirm vehicle model on IDENTIFICATION PLATE. Refer to MODEL VARIATION .

Fig 6: CONSULT-II Display
Courtesy of NISSAN MOTOR CO., U.S.A.
Touch "WRITE CONFIGURATION" on "CONFIGURATION" screen.

Fig 7: CONSULT-II Display
Courtesy of NISSAN MOTOR CO., U.S.A.
Touch YES".
For canceling, touch "NO".

Fig 8: CONSULT-II Display
Courtesy of NISSAN MOTOR CO., U.S.A.
Using the following flow charts, identify the correct model and configuration list. Confirm and/or change setting value for each item according to the configuration list.
NOTE: Confirm vehicle model on IDENTIFICATION PLATE. Refer to MODEL VARIATION .

Fig 9: Model And Configuration Identification Flow Chart (King Cab XE)
Courtesy of NISSAN MOTOR CO., U.S.A.

Fig 10: Model And Configuration Identification Flow Chart (King Cab SE)
Courtesy of NISSAN MOTOR CO., U.S.A.

Fig 11: Model And Configuration Identification Flow Chart (King Cab LE)
Courtesy of NISSAN MOTOR CO., U.S.A.

Fig 12: Model And Configuration Identification Flow Chart (Crew Cab XE)
Courtesy of NISSAN MOTOR CO., U.S.A.

Fig 13: Model And Configuration Identification Flow Chart (Crew Cab SE)
Courtesy of NISSAN MOTOR CO., U.S.A.

Fig 14: Model And Configuration Identification Flow Chart (Crew Cab LE)
Courtesy of NISSAN MOTOR CO., U.S.A.
Touch "CHNG SETTING" on "WRITE CONFIGURATION" screen.
CAUTION: Make sure to touch "CHNG SETTING" even if the indicated configuration of brand-new BCM is same as the desirable configuration.
If not, configuration which is set automatically by selecting vehicle model cannot be memorized.
Touch "OK" on "WRITE CONFIGURATION" screen.
If "CANCEL" is touched, it will return to previous screen.

Fig 15: CONSULT-II Display
Courtesy of NISSAN MOTOR CO., U.S.A.
Wait until the next screen during setting.

Fig 16: CONSULT-II Display
Courtesy of NISSAN MOTOR CO., U.S.A.
WRITE CONFIGURATION results are printed out automatically. Confirm "WRITE CONFIGURATION" is correctly executed by comparing sheet automatically printed out with applicable configuration list shown in step 9.

Fig 17: CONSULT-II Printout
Courtesy of NISSAN MOTOR CO., U.S.A.
Touch "OK" on "WRITE CONFIGURATION" screen.
WRITE CONFIGURATION is completed.

Fig 18: CONSULT-II Display

Courtesy of NISSAN MOTOR CO., U.S.A.