LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Nissan-Datsun >> 2002 >> Sentra SE-R, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 1079 (BCM (Body Control Module)) >> BCM (Body Control Module) >> Configuration >> Write Configuration Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Write Configuration Procedure

WARNING: This page is about a different car, the 2004 Nissan Quest. However, it is still accessible from the selected car via links, so may be relevant.
CAUTION: If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be detected in self-diagnosis depending on control unit which carries out CAN communication. 
  1. With ignition switch OFF, connect CONSULT-II and CONSULT-II CONVERTER to data link connector and turn ignition switch ON.
    Fig 1: Identifying Data Link Connector
    G03500761Courtesy of NISSAN MOTOR CO., U.S.A.
  2. Touch "START (NISSAN BASED VHCL)".
    Fig 2: Displaying "START (NISSAN BASED VHCL)" Mode
    G03500762Courtesy of NISSAN MOTOR CO., U.S.A.
  3. Touch "BCM" on "SELECT SYSTEM" screen. If "BCM" is not indicated, go to LAN Article to check data link connector (DLC) circuit.
    Fig 3: Displaying "SELECT SYSTEM" Screen
    G03500763Courtesy of NISSAN MOTOR CO., U.S.A.
  4. Touch "BCM" on "SELECT TEST ITEM" screen.
    Fig 4: Displaying "BCM" On "SELECT TEST ITEM" Screen
    G03500764Courtesy of NISSAN MOTOR CO., U.S.A.
  5. Touch "CONFIGURATION" on "SELECT DIAG MODE" screen.
    Fig 5: Displaying "CONFIGURATION" On "SELECT DIAG MODE" Screen
    G03500765Courtesy of NISSAN MOTOR CO., U.S.A.
  6. Touch "V42" and "OK" on "VEHICLE SELECT" screen. For canceling, touch "CANCEL" on "VEHICLE SELECT" screen.
    NOTE: Confirm vehicle model on IDENTIFICATION PLATE. Refer to "MODEL VARIATION " .
    Fig 6: Displaying "VEHICLE SELECT" Screen
    G03500766Courtesy of NISSAN MOTOR CO., U.S.A.
  7. Touch "WRITE CONFIGURATION" on "CONFIGURATION" screen.
    Fig 7: Displaying "Write Configuration" On "Configuration" Screen
    G03500767Courtesy of NISSAN MOTOR CO., U.S.A.
  8. Touch "OK".

    For canceling, touch "CANCEL".

    Fig 8: Displaying CONFIGURATION Mode
    G03500768Courtesy of NISSAN MOTOR CO., U.S.A.
  9. Touch "WITH" or "WITHOUT" on "WRITE CONFIGURATION" screen based on the following ITEM LIST.
    ITEM SPECIFICATION

    ITEM SET VAL
    AUTO LIGHT WITH <->WITHOUT
    FR FOG LAMP WITH <->WITHOUT
    Fig 9: Displaying "WRITE CONFIGURATION" Screen
    G03500769Courtesy of NISSAN MOTOR CO., U.S.A.
    NOTE: Confirm vehicle model on IDENTIFICATION PLATE. Refer to "MODEL VARIATION " .
  10. Touch "CHNG SETTING" on "WRITE CONFIGURATION" screen.
    CAUTION: Make sure to touch "CHNG SETTING" even if the indicated configuration of brand-new BCM is same as the desirable configuration. 
    If not, configuration which is set automatically by selecting vehicle model cannot be memorized. 
  11. Touch "OK" on "WRITE CONFIGURATION" screen.

    If "CANCEL" is touched, it will return to previous screen.

    Fig 10: Displaying "WRITE CONFIGURATION" Screen
    G03500770Courtesy of NISSAN MOTOR CO., U.S.A.
  12. Wait until the next screen during setting.
    Fig 11: Displaying "WRITE CONFIGURATION" Screen
    G03500771Courtesy of NISSAN MOTOR CO., U.S.A.
  13. WRITE CONFIGURATION results are printed out automatically. Check "WRITE CONFIGURATION" is correctly executed by comparing sheet automatically printed out with desirable configuration.
    Fig 12: Displaying "WRITE CONFIGURATION" Screen
    G03500772Courtesy of NISSAN MOTOR CO., U.S.A.
  14. Touch "OK" on "WRITE CONFIGURATION" screen. WRITE CONFIGURATION is completed.
    Fig 13: Displaying "WRITE CONFIGURATION" Screen
    G03500773Courtesy of NISSAN MOTOR CO., U.S.A.
scientia non olet · About LEMON Manuals