LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Nissan-Datsun >> 2003 >> Sentra SE-R, Automatic >> Repair and Diagnosis >> External Pages >> Different car >> Section 1685 (Body Control System) >> BCM (Body Control Module) >> Configuration >> Write Configuration Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Write Configuration Procedure

WARNING: This page is about a different car, the 2006 Nissan Titan. However, it is still accessible from the selected car via links, so may be relevant.
CAUTION: If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be detected in self-diagnosis depending on control unit which carries out CAN communication.
  1. With ignition switch OFF, connect CONSULT-II and CONSULT-II CONVERTER to data link connector and turn ignition switch ON.
    Fig 1: Locating Data Link Connector
    G04187192Courtesy of NISSAN MOTOR CO., U.S.A.
  2. Touch "START (NISSAN BASED VHCL)".
    Fig 2: Consult-II Display - START (NISSAN BASED VHCL)
    G04151184Courtesy of NISSAN MOTOR CO., U.S.A.
  3. Touch "BCM" on "SELECT SYSTEM" screen.

    If "BCM" is not indicated, go to "CONSULT-II DATA LINK CONNECTOR (DLC) CIRCUIT ".

    Fig 3: Consult-II SELECT SYSTEM Display Screen
    G04083859Courtesy of NISSAN MOTOR CO., U.S.A.
  4. Touch "BCM" on "SELECT TEST ITEM" screen.
    Fig 4: Consult-II SELECT TEST ITEM Display Screen
    G04136565Courtesy of NISSAN MOTOR CO., U.S.A.
  5. Touch "CONFIGURATION" on "SELECT DIAG MODE" screen.
    Fig 5: Consult-II SELECT DIAG MODE Display Screen
    G04083861Courtesy of NISSAN MOTOR CO., U.S.A.
  6. Touch "A60" and "OK" on "VEHICLE SELECT" screen. For canceling, touch "CANCEL" on "VEHICLE SELECT" screen.
    NOTE: Confirm vehicle model. Refer to "MODEL VARIATION " .
    Fig 6: CONSULT-II Display - SELECT DIAG MODE
    G04188935Courtesy of NISSAN MOTOR CO., U.S.A.
  7. Touch "WRITE CONFIGURATION" on "SELECT CONFIG ITEM" screen.
    Fig 7: CONSULT-II Display - SELECT CONFIG ITEM
    G04188936Courtesy of NISSAN MOTOR CO., U.S.A.
  8. Touch "YES".

    For canceling, touch "NO".

    Fig 8: CONSULT-II Display - CONFIGURATION
    G04188937Courtesy of NISSAN MOTOR CO., U.S.A.
  9. Set by touching selection on "WRITE CONFIGURATION" screen based on the following ITEM LIST.
    ITEM REFERENCE

    ITEM SET VAL
    KEYLESS ENTRY WITH <==> WITHOUT
    AUTO LIGHT WITH <==> WITHOUT
    FR FOG LAMP WITH <==> WITHOUT
    DTRL WITH <==> WITHOUT
    DISPLAY STYLE MODE1(1) <==> MODE2>(2)
    THEFT ALARM WITH <==> WITHOUT
    (1) Without NAVI
    (2) With NAVI

    Do not apply MODE3 or MODE4.

    NOTE: Confirm vehicle model. Refer to "MODEL VARIATION " .
  10. Touch "CHNG SETTING" on "WRITE CONFIGURATION" screen.
    CAUTION: Make sure to touch "CHNG SETTING" even if the indicated configuration of new BCM is same as the desirable configuration.
    If not, configuration which is set automatically by selecting vehicle model cannot be memorized.
  11. Touch "OK" on "WRITE CONFIGURATION" screen.

    If "CANCEL" is touched, it will return to previous screen.

    Fig 9: CONSULT-II Display - WRITE CONFIGURATION
    G04188938Courtesy of NISSAN MOTOR CO., U.S.A.
  12. Wait until the next screen during setting.
    Fig 10: CONSULT-II Display - WRITE CONFIGURATION
    G04188939Courtesy of NISSAN MOTOR CO., U.S.A.
  13. WRITE CONFIGURATION results are printed out automatically. Confirm "WRITE CONFIGURATION" is correctly executed by comparing sheet automatically printed out with applicable configuration list shown in step  9.
    Fig 11: CONSULT-II Display - WRITE CONFIGURATION
    G04188940Courtesy of NISSAN MOTOR CO., U.S.A.
  14. Touch "OK" on "WRITE CONFIGURATION" screen.

    WRITE CONFIGURATION is completed.

    Fig 12: CONSULT-II Display - WRITE CONFIGURATION
    G04188941Courtesy of NISSAN MOTOR CO., U.S.A.
scientia non olet · About LEMON Manuals