Basic Inspection

1. Check service records for any recent repairs that may indicate a related malfunction, or a current need for scheduled maintenance.
2. Open engine hood and check the following:
   • Harness connectors for improper connections
   • Wiring harness for improper connections, pinches and cut
   • Vacuum hoses for splits, kinks and improper connections
   • Hoses and ducts for leaks
   • Air cleaner clogging
   • Gasket
     Fig 1: Checking Harness Connectors For Improper Connections

     Courtesy of NISSAN MOTOR CO., U.S.A.
3. Confirm that electrical or mechanical loads are not applied.
   • Headlamp switch is OFF.
   • Air conditioner switch is OFF.
   • Rear window defogger switch is OFF.
   • Steering wheel is in the straight-ahead position, etc.
4. Start engine and warm it up until engine coolant temperature indicator points the middle of gauge.

   Ensure engine stays below 1, 000 rpm.

   Fig 2: Identifying Engine Coolant Temperature

   Courtesy of NISSAN MOTOR CO., U.S.A.
5. Run engine at about 2, 000 rpm for about 2 minutes under no load.
6. Make sure that no DTC is displayed with CONSULT-III or GST.

OK or NG 

OK: GO TO  3.

NG: GO TO 2.

Fig 3: Identifying Engine RPM Meter

Courtesy of NISSAN MOTOR CO., U.S.A.

Repair or replace components as necessary according to corresponding Diagnostic Procedure.

: GO TO 3.

With CONSULT-III 

1. Run engine at about 2, 000 rpm for about 2 minutes under no load.
2. Rev engine (2, 000 to 3, 000 rpm) two or three times under no load, then run engine at idle speed for about 1 minute.
   Fig 4: Checking Target Idle Speed

   Courtesy of NISSAN MOTOR CO., U.S.A.
3. Read idle speed in "DATA MONITOR" mode with CONSULT-III. Refer to "IDLE SPEED ".

   675 ± 50 rpm (in P or N position) 

Without CONSULT-III 

1. Run engine at about 2, 000 rpm for about 2 minutes under no load.
2. Rev engine (2, 000 to 3, 000 rpm) two or three times under no load, then run engine at idle speed for about 1 minute.
3. Check idle speed. Refer to "IDLE SPEED ".

   675 ± 50 rpm (in P or N position) 

OK or NG 

OK: GO TO  10.

NG: GO TO 4.

1. Stop engine.
2. Perform "ACCELERATOR PEDAL RELEASED POSITION LEARNING ".

: GO TO 5.

Perform "THROTTLE VALVE CLOSED POSITION LEARNING ".

: GO TO 6.

Refer to "IDLE AIR VOLUME LEARNING ".

Is Idle Air Volume Learning carried out successfully? 

Yes or No 

Yes: GO TO 7.

No:

1. Follow the instruction of Idle Air Volume Learning.
2. GO TO  4.

With CONSULT-III 

1. Start engine and warm it up to normal operating temperature.
2. Read idle speed in "DATA MONITOR" mode with CONSULT-III. Refer to "IDLE SPEED ".

   675 ± 50 rpm (in P or N position) 

Without CONSULT-III 

1. Start engine and warm it up to normal operating temperature.
2. Check idle speed. Refer to "IDLE SPEED ".

   675 ± 50 rpm (in P or N position) 

OK or NG 

OK: GO TO  10.

NG: GO TO 8.

Check the following.

• Check camshaft position sensor (PHASE) and circuit. Refer to DTC P0340, P0345 CMP SENSOR (PHASE) .
• Check crankshaft position sensor (POS) and circuit. Refer to DTC P0335 CKP SENSOR (POS) .

OK or NG 

OK: GO TO 9.

NG >>

1. Repair or replace.
2. GO TO  4.

1. Substitute another known-good ECM to check ECM function. (ECM may be the cause of an incident, but this is a rare case.)
2. Perform initialization of NVIS (NATS) system and registration of all NVIS (NATS) ignition key IDs. Refer to "NVIS(NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS) ".

: GO TO  4.

1. Run engine at idle.
2. Check ignition timing with a timing light.

   Refer to "IGNITION TIMING ".

   15 ± 5° BTDC (in P or N position) 

OK or NG 

OK: GO TO  19.

NG: GO TO 11.

Fig 5: Checking Ignition Timing

Courtesy of NISSAN MOTOR CO., U.S.A.

1. Stop engine.
2. Perform "ACCELERATOR PEDAL RELEASED POSITION LEARNING ".

: GO TO 12.

Perform "THROTTLE VALVE CLOSED POSITION LEARNING ".

: GO TO 13.

Refer to "IDLE AIR VOLUME LEARNING ".

Is Idle Air Volume Learning carried out successfully? 

Yes or No 

Yes: GO TO  14.

No:

1. Follow the instruction of Idle Air Volume Learning.
2. GO TO  4.

With CONSULT-III 

1. Start engine and warm it up to normal operating temperature.
2. Read idle speed in "DATA MONITOR" mode with CONSULT-III. Refer to "IDLE SPEED ".

   675 ± 50 rpm (in P or N position) 

Without CONSULT-III 

1. Start engine and warm it up to normal operating temperature.
2. Check idle speed. Refer to "IDLE SPEED ".

   675 ± 50 rpm (in P or N position) 

OK or NG 

OK: GO TO 15.

NG: GO TO  17.

1. Run engine at idle.
2. Check ignition timing with a timing light.

   Refer to "IGNITION TIMING ".

   15 ± 5° BTDC (in P or N position) 

OK or NG 

OK: GO TO  19.

NG: GO TO 16.

Fig 6: Checking Ignition Timing

Courtesy of NISSAN MOTOR CO., U.S.A.

Check timing chain installation. Refer to "TIMING CHAIN ".

OK or NG 

OK: GO TO 17.

NG >>

1. Repair the timing chain installation.
2. GO TO  4.

Check the following.

• Check camshaft position sensor (PHASE) and circuit. Refer to DTC P0340, P0345 CMP SENSOR (PHASE) .
• Check crankshaft position sensor (POS) and circuit. Refer to DTC P0335 CKP SENSOR (POS) .

OK or NG 

OK: GO TO 18.

NG >>

1. Repair or replace.
2. GO TO  4.

1. Substitute another known-good ECM to check ECM function. (ECM may be the cause of an incident, but this is a rare case.)
2. Perform initialization of NVIS (NATS) system and registration of all NVIS (NATS) ignition key IDs. Refer to "NVIS(NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS) ".

: GO TO  4.

Did you replace the ECM, referring this Basic Inspection procedure?

Yes or No 

Yes:

1. Perform "VIN REGISTRATION ".
2. INSPECTION END 

No: INSPECTION END