LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Nissan-Datsun >> 2003 >> Sentra SE-R, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 1292 (Body Control Module) >> BCM (Body Control Module) >> Configuration >> Write Configuration Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Write Configuration Procedure

WARNING: This page is about a different car, the 2004 Nissan Maxima. However, it is still accessible from the selected car via links, so may be relevant.
CAUTION: If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be detected in self-diagnosis depending on control unit which carries out CAN communication.
  1. With ignition switch OFF, connect CONSULT-II and CONSULT-II CONVERTER to data link connector and turn ignition switch ON.
    Fig 1: Identifying Data Link Connector
    G03495427Courtesy of NISSAN MOTOR CO., U.S.A.
  2. Touch "START (NISSAN BASED VHCL)".
    Fig 2: Display Start Nissan Based Vhcl
    G03495428Courtesy of NISSAN MOTOR CO., U.S.A.
  3. Touch "BCM" on "SELECT SYSTEM" screen. If "BCM" is not indicated, go to LAN article to check data link connector (DLC) circuit.
    Fig 3: Display Select System
    G03495429Courtesy of NISSAN MOTOR CO., U.S.A.
  4. Touch "BCM" on "SELECT TEST ITEM" screen.
    Fig 4: Display Select Test Item
    G03495430Courtesy of NISSAN MOTOR CO., U.S.A.
  5. Touch "CONFIGURATION" on "SELECT DIAG MODE" screen.
    Fig 5: Display Select Diag Mode
    G03495431Courtesy of NISSAN MOTOR CO., U.S.A.
  6. Touch "A34" and "OK" on "VEHICLE SELECT' screen. For canceling, touch "CANCEL" on "VEHICLE SELECT" screen.
    NOTE: Confirm vehicle model on IDENTIFICATION PLATE. Refer to MODEL VARIATION in General Information.
    Fig 6: Display Vehicle Select
    G03495432Courtesy of NISSAN MOTOR CO., U.S.A.
  7. Touch "WRITE CONFIGURATION" on "CONFIGURATION" screen.
    Fig 7: Display Write Configuration
    G03495433Courtesy of NISSAN MOTOR CO., U.S.A.
  8. Touch "OK'.

    For canceling, touch "CANCEL".

    Fig 8: Display Touch OK
    G03495434Courtesy of NISSAN MOTOR CO., U.S.A.
  9. Touch "CAN DTRL" or "WITHOUT" on "WRITE CONFIGURATION" screen based on the following ITEM LIST.
    SET VAL ITEM

    ITEM SET VAL NOTE
    DTRL (Daytime running light) CAN DTRL Canadian specification vehicle
    WITHOUT United States specification vehicle
    NOTE: Confirm vehicle model on IDENTIFICATION PLATE. Refer to MODEL VARIATION in General Information.
    Fig 9: Display Write Configuration (1 Of 2)
    G03495435Courtesy of NISSAN MOTOR CO., U.S.A.
  10. Touch "CHNG SETTING" on "WRITE CONFIGURATION" screen.
    CAUTION: Make sure to touch "CHNG SETTING" even if the indicated configuration of brand-new BCM is same as the desirable configuration.

    If not, configuration which is set automatically by selecting vehicle model cannot be memorized. 

  11. Touch "OK" on "WRITE CONFIGURATION" screen. If "CANCEL" is touched, it will return to previous screen.
    Fig 10: Display Write Configuration (2 Of 2)
    G03495436Courtesy of NISSAN MOTOR CO., U.S.A.
  12. Wait until the next screen during setting.
    Fig 11: Display Write Configuration
    G03495437Courtesy of NISSAN MOTOR CO., U.S.A.
  13. WRITE CONFIGURATION results are printed out automatically. Check "WRITE CONFIGURATION" is correctly executed by comparing sheet automatically printed out with desirable configuration.
    Fig 12: Display Write Configuration
    G03495438Courtesy of NISSAN MOTOR CO., U.S.A.
  14. Touch "OK" on "WRITE CONFIGURATION" screen. WRITE CONFIGURATION is completed.
    Fig 13: Display Write Configuration
    G03495439Courtesy of NISSAN MOTOR CO., U.S.A.
scientia non olet · About LEMON Manuals