LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Pontiac >> 2002 >> Aztek AWD >> Repair and Diagnosis >> Engine Performance >> System >> Engine Controls Self-Diagnostics >> Diagnostic Tests >> DTC P0443: EVAP Purge Solenoid Control Circuit >> Diagnostic Procedures
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Diagnostic Procedures

  1. Did you perform the Diagnostic System Check-Engine Controls? If yes, go to next step. If no, see DIAGNOSTIC SYSTEM CHECK - ENGINE CONTROLS  under SELF-DIAGNOSTIC SYSTEM.
  2. Turn ON the ignition, with the engine OFF. With a scan took, command the EVAP purge valve to 50 percent, and then to 0 percent. Does the EVAP purge valve respond to the commanded state? If yes, go to next step. If no, go to step  4.
  3. Observe the Freeze Frame/Failure Records for this DTC. Turn OFF the ignition for 30 seconds. Start the engine. Operate the vehicle within the Conditions for Running DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records. Did the DTC fail this ignition cycle? If yes, go to next step. If no, see INTERMITTENT CONDITIONS  under SELF-DIAGNOSTIC SYSTEM.
  4. Turn OFF the ignition. Disconnect the EVAP purge valve harness connector. Turn ON the ignition, with the engine OFF. Probe the ignition voltage circuit at the EVAP purge valve harness connector with a test lamp connected to a good ground. Does the test lamp illuminate? If yes, go to next step. If no, go to step  11.
  5. Connect a test lamp between the control circuit and the ignition voltage circuit of the EVAP purge valve harness connector. With a scan tool, command the EVAP purge valve to 50 percent and then to 0 percent. Does the test lamp turn ON when the EVAP purge valve is commanded to 50 percent and OFF when the purge valve is commanded to 0 percent? If yes, go to step  9. If no, go to next step.
  6. Does the test lamp remain illuminated with each command? If yes, go to step  8. If no, go to next step.
  7. Test the control circuit of the EVAP purge valve for an open or short to voltage. Did you find and correct the condition? If yes, go to step  14. If no, go to step  10.
  8. Test the control circuit of the EVAP purge valve for a short to ground. Did you find and correct the condition? If yes, go to step  14. If no, go to step  13.
  9. Inspect for poor connections at the harness connector of the EVAP purge valve. Did you find and correct the condition? If yes, go to step  14. If no, go to step  12.
  10. Inspect for poor connections at the harness connector of the control module. Did you find and correct the condition? If yes, go to step  14. If no, go to step  13.
  11. Repair the ignition voltage circuit of the EVAP purge valve for an open or a short to ground. Replace the fuse if necessary. After repairs, go to step  14.
  12. Replace the EVAP purge valve. See appropriate REMOVAL, OVERHAUL & INSTALLATION article. After repairs, go to step  14.
  13. Replace the PCM. See appropriate REMOVAL, OVERHAUL & INSTALLATION article. Reprogram PCM. See POWERTRAIN CONTROL MODULE  under PROGRAMMING. After repairs, go to next step.
  14. Clear the DTCs with a scan tool. Turn OFF the ignition for 30 seconds. Start the engine. Operate the vehicle within the Conditions for Running DTC. Does the DTC run and pass? If yes, go to next step. If no, go to step  2.
  15. Observe the stored information, Capture Info with a scan tool. Does the scan tool display any DTCs that you have not diagnosed? If yes, see DIAGNOSTIC TROUBLE CODE DEFINITIONS . If no, system is okay.
scientia non olet · About LEMON Manuals