Section 28 (Basic Engine, V6)
WARNING: This page is about a different car, the 2009 Saab 9-3. However, it is still accessible from the selected car via links, so may be relevant.
- Repair Instructions
- Power train removal
- Power train, to remove, 4WD
- Power unit, fitting
- Power train, to fit, 4WD
- Timing cover
- Timing cover in situ (vehicle)
- Replacing the engine (power train on the subframe)
- Replacing the engine (power unit on the subframe), 4WD
- Valve seal, front
- Valve spring, front
- Valve spring, rear
- Valve mechanism, rear cylinder head, B284 (new version)
- Valve mechanism, front cylinder head, B284 (new version)
- Camshaft cover, rear, B284
- Camshaft cover, front, B284
- Camshaft covers, removed engine
- Engine compression test
- Drive belt, auxiliaries
- Engine mounting, right
- Engine mounting, left-hand
- Belt tensioner
- Crankshaft pulley
- Front crankshaft seal
- Rear crankshaft seal
- Rear crankshaft seal in car
- Solenoid valve, intake camshaft, front cylinder bank (695F)
- Solenoid valve seal, intake camshaft, front cylinder bank (695F)
- Solenoid valve, intake camshaft, rear cylinder bank (695R)
- Solenoid valve seal, intake camshaft, rear cylinder bank (695R)
- Camshaft drive, B284 (new version)
- Camshafts in situ, front cylinder head, B284 (new version)
- Camshafts in situ, rear cylinder head, B284 (new version)
- Check the engine oil pressure.
- Oil pressure switch
- Oil sump
- Oil pump
- Level sensor, engine oil (243)
- Oil filler pipe
- Rear torque arm
- Rear torque arm, 4WD
- Front torque arm
- Spark plug
- Valve cone, rear cylinder head, B284 (new version)
- Valve cone, front cylinder head, B284 (new version)
- Valve seal, rear
- Camshaft rocker arm, rear cylinder head B284 (new version)
- Rocker arm, front cylinder head camshaft, B284 (new version)
- Centring tool, engine and subframe, 4WD
- Front cylinder head gasket
- Cylinder head, gasket, rear (new version camshaft drive)
- Cylinder head, B284
- Description and operation
- Component Locator
- Specifications
- Special Tools and Equipment
- EN-46103 Fitting tool
- EN-46105 Adjustment tool
- EN-46106 Flywheel locking attachment
- EN-46108 Fixing tool
- EN-46109-2 Centring tool
- EN-46110 Valve spring depressor
- EN-46111 Sleeve
- EN-46117 Fitting tool
- EN-46121 Guide pin
- EN-47635 Fitting tool
- EN-47839 Fitting tool
- EN-47981 Holding tool, pulley
- EN-48313 Timing chain holding tool
- EN-47982 Puller
- EN-48383 Adjustment tool
- J-24254-A Fitting tool
- J-41818 Removal tool
- J-41998 Fitting tool
- J-43654 Removal/fitting tool
- J-5590 Drift
- KM-6313-300 Support
- 32 025 037 Hook for lifting yoke
- 32 025 048 Holder
- 32 025 051 Oil filter spanner
- 32 025 053 Holder
- 32 025 059 Support
- 32 025 060 Tool kit
- 32 025 061 Crow foot spanner
- 32 025 062 Crow foot spanner
- 83 94 173 Air nipple for spark plug hole
- 83 95 360 Support, crankshaft belt pulley
- 87 92 574 Holder
- Km 6313-200
- 83 96 145 Centring fixture, subframe - engine