LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Saturn >> 2005 >> Relay FWD >> Repair and Diagnosis >> Transmission >> Automatic Trans >> Shift Interlock System >> Diagnostic Information And Procedures >> DTC B2705 >> Test Description
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. 2:  Listen for an audible click when the A/T shift lock control solenoid operates. Command both the ON and OFF states. Repeat the commands as necessary.
  2. 3:  This step tests for battery voltage at the control circuit of the A/T shift lock control solenoid.
  3. 4:  This step tests for an open or short to ground at the control circuit of the A/T shift lock control solenoid.
  4. 5:  This step tests for an open at the ground circuit of the A/T shift lock control solenoid.
DTC B2705

Step Action Yes No
Schematic Reference: Automatic Transmission Shift Lock Control Schematics 
Connector End View Reference: Automatic Transmission Shift Lock Control Connector End Views  or Computer/Integrating Systems Connector End Views in Computer/Integrating Systems
1 Did you perform the Diagnostic System Check - Vehicle? Go to Step 2  Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2 
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. With a scan tool, command the brake to shift control output control ON and OFF.
  4. With a scan tool, observe the BTSI solenoid parameter in the body control module (BCM) data list.
Does the A/T shift lock control solenoid turn ON and OFF with each command?		 Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems Go to Step 3 
3 
  1. Turn OFF the ignition.
  2. Disconnect the A/T shift lock control solenoid.
  3. Connect a test lamp between the shift lock solenoid control circuit at the connector of the A/T shift lock solenoid and a good ground.
  4. Turn ON the ignition, with the engine OFF.
  5. With a scan tool, command the brake to shift control output control ON and OFF several times.
Does the test lamp illuminate ON and OFF with each command?		 Go to Step 5  Go to Step 4 
4  Test the control circuit of the A/T shift lock control solenoid for an open or short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 10  Go to Step 7 
5  Test the A/T shift lock control solenoid ground circuit for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 10  Go to Step 6 
6 Inspect for poor connections at the harness connector of the A/T shift lock control solenoid. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 10  Go to Step 8 
7 Inspect for poor connections at the harness connector of the BCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 10  Go to Step 9 
8 Replace the A/T shift lock control solenoid. Refer to Automatic Transmission Shift Lock Actuator Replacement .
Did you complete the replacement?		 Go to Step 10  -
9
IMPORTANT: Perform the set up procedures for the BCM.
Replace the BCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.Did you complete the replacement?		 Go to Step 10  -
10
  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.
Does the DTC reset?		 Go to Step 2  System OK
scientia non olet · About LEMON Manuals