LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Saturn >> 2010 >> Sky Red Line, Automatic >> Repair and Diagnosis >> Engine Performance >> Engine Control Systems >> Engine Controls And Fuel - 2.0L - Repair Instructions >> Repair Instructions >> Fuel Injection Fuel Rail Assembly Replacement >> Removal Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Removal Procedure

    Fig 1: Identifying Fuel Injector Wiring Harness Electrical Connector
    GM1826857Courtesy of GENERAL MOTORS CORP.
  1. Disconnect the engine wiring harness electrical connector (1) from the fuel injector wiring harness electrical connector.
  2. Remove the intake manifold. Refer to Intake Manifold Replacement .
    3. Fig 2: View Of Fuel Injector Insulator
    GM1769947Courtesy of GENERAL MOTORS CORP.
  3. Remove the fuel injector insulator.
    4. Fig 3: Identifying High Pressure Fuel Pump Connector & Clip
    GM1826282Courtesy of GENERAL MOTORS CORP.
  4. Relieve the high side fuel system pressure. Refer to Fuel Pressure Relief (Low Pressure without Special Tool)  or Fuel Pressure Relief (Low Pressure with CH 48027)  or Fuel Pressure Relief (Low Pressure Side with CH 48027-100)  or Fuel Pressure Relief (High Pressure Side) .
  5. Disconnect the engine wiring harness electrical connector (1) from the high pressure fuel pump.
    6. Fig 4: View Of High Pressure Fuel Pump Cover & Bolts
    GM1826280Courtesy of GENERAL MOTORS CORP.
  6. Remove the high pressure fuel pump cover bolts.
  7. Remove the high pressure fuel pump cover.
  8. Remove the engine wiring harness clip from the high pressure fuel pump cover.
    9. Fig 5: View Of High Pressure Fuel Pump Insulator
    GM1829002Courtesy of GENERAL MOTORS CORP.
  9. Remove the high pressure fuel pump insulator.
    10. Fig 6: View Of High Pressure Fuel Pipe
    GM1828941Courtesy of GENERAL MOTORS CORP.
  10. Loosen the high pressure fuel pipe fitting at the fuel pump.
  11. Loosen the high pressure fuel pipe fitting at the fuel rail.
  12. Remove and discard the high pressure fuel pipe.
    13. Fig 7: Identifying Fuel Rail & Bolts
    GM1829953Courtesy of GENERAL MOTORS CORP.
  13. Disconnect the fuel injector wiring harness electrical connectors from the fuel injectors.
  14. Remove the fuel rail bolts (1).
    15. NOTE: Carefully remove the fuel rail. The fuel injectors may come out of the cylinder head with the fuel rail.
    NOTE: A fuel injector may remain stuck in the cylinder head. If this occurs, complete the following steps:
  15. Carefully remove the fuel rail (2).
    1. Remove the fuel injector hold-down clamp before removing the fuel injector.
      NOTE: Use the injector remover and slide hammer to pull the fuel injector straight out along the fuel injector axis. DO NOT tilt or twist the fuel injector during this process.
    2. Use J-37281-A:  injector remover, and J 2619-01:  hammer to remove the fuel injector.
    3. Once injectors have been removed it will be necessary to clean and rebuild all the injectors. Refer to Fuel Rail and Injectors Cleaning and Inspection .
    16. Fig 8: View Of Fuel Rail Fuel Pressure Sensor
    GM1829977Courtesy of GENERAL MOTORS CORP.
    NOTE: Applying force to the plastic housing of the sensor will destroy the sensor. To tighten or loosen, only apply force to the attached hexagon.
  16. If replacing the fuel rail, remove the fuel injection fuel rail fuel pressure sensor.
  17. Remove the fuel injector wiring harness.
scientia non olet · About LEMON Manuals