Data List/Active Test

DATA LIST

NOTE: Using the DATA LIST displayed by the hand-held tester or the OBD II scan tool, you can read the value of the switches, sensors, actuators and so on without parts removal. Reading the DATA LIST as a first step of troubleshooting is one method to shorten diagnostic time.

NOTE: The values given below for "Normal Condition" are representative values. A vehicle may still be normal even if its value differs from those listed here. Do not solely depend on the "Normal Condition" here when deciding whether a part is faulty or not.

Warm up the engine.
Turn the ignition switch OFF.
Connect the hand-held tester or the OBD II scan tool to the DLC3.
Turn the ignition switch ON.
Push the "ON" button of the hand-held tester or the OBD II scan tool.
Select the item "DIAGNOSIS / ENHANCED OBD II / DATA LIST".

According to the display on tester, read the "DATA LIST".

DATA LIST

Hand-Held Tester Display

Measurement Item/Range (Display)

Normal Condition⁽¹⁾

Diagnostic Note

INJECTOR

Injection Period Of The No. 1 Cylinder/
Min.: 0 ms, Max.: 32.64 ms

Idling: 1.0 to 3.0 ms

IGN ADVANCE

Ignition Timing Advance For No. 1 Cylinder/
Min.: -64 deg., Max.: 63.5 deg.

Idling: BTDC 2 to 14°

IAC DUTY RATIO

Intake Air Control Valve Duty Ratio Opening Ratio Rotary Solenoid Type ISC Valve
Min.: 0%, Max.: 99%

Idling: 20 to 40 %
Running Without Load (2,500 RPM)

CALC LOAD

Calculated Load By ECM/
Min.: 0 %, Max.: 100 %

Idling: 10 to 30 %
Running Without Load (2,500 RPM): 10 to 30 %

MAF

Air Flow Rate From MAF Sensor/
Min.: 0 gm/s, Max.: 655 gm/s

Idling: M/T 0.54 to 4.33 gm/sec.
A/T 0.58 to 4.67 gm/sec.
Running Without Load (2,500 RPM): 3.33 to 9.17 gm/sec.

If The Value Is Approximately 0.0 gm/s:

Mass Air Flow Meter Power Source Circuit Open
Vg Circuit Open Or Short
If The Value Is 160.0 gm/s Or More:
E2G Circuit Open

ENGINE SPD

Engine Speed/
Min.: 0 RPM, Max.: 16383 RPM

Idling: M/T 600 to 700 RPM
A/T 650 to 750 RPM

COOLANT TEMP

Coolant Temperature/
Min.: -40 °C, Max.: 140 °C

After Warming Up: 80 to 100°C (176 to 203°F)

If The Value Is -40°C (-40°F): Sensor Circuit Is Open.
If The Value Is 140°C (284°F Or More): Sensor Circuit Is Shorted.

INTAKE AIR

Intake Air Temperature/
Min.: -40 °C, Max.: 140 °C

Equivalent To Ambient Temp.

THROTTLE POS

Absolute Throttle Position Sensor/
Min.: 0 %, Max.: 100 %

Throttle Fully Closed: 0 To 10 %
Throttle Fully Open: 70 To 100 %

Read The Value With The Ignition Switch ON (Do Not Start Engine)

CTP SW

Closed Throttle Position Switch/
ON or OFF

Throttle Fully Closed: ON
Throttle Fully Open: OFF

VEHICLE SPD

Vehicle Speed/
Min.: 0 km/h, Max.: 255 km/h

Actual Vehicle Speed

O2S B1 S1

Heated Oxygen Sensor Output Voltage For Bank 1 Sensor 2/
Min.: 0 V, Max.: 1.0 V

Idling: 0 to 1.0 V

Performing The INJ VOL or A/F CONTROL Function Of The ACTIVE TEST Enables The Technician To Check The Voltage Output Of Each Sensor.

O2S B1 S2

Heated Oxygen Sensor Output Voltage For Bank 2 Sensor 2/
Min.: 0 V, Max.: 1.0 V

Idling: 0 to 1.0 V

VAPOR PRESS

Vapor Pressure/
Min.: -4.125 kPa, Max.: 2.125 kPa

Fuel Tank Cap Removed: 0 kPa

Pressure Inside Of Fuel Tank As Read By The Vapor Pressure Sensor

SHORT FT #1

Short term fuel trim of bank 1/
Min.: -100 %, Max.: 100%

0 +/- 20%

LONG FT #1

Long Term Fuel Trim Of Bank 1/
Min.: -100 %, Max.: 100 %

0 +/- 20%

This Item Is The Overall Fuel Compensation Carried Out In Long-Term To Compensate For A Continual Deviation Of The Short-Term Fuel Trim From The Central Value.

TOTAL FT #1

Total Fuel Trim Of Bank 1:
Average Value For Fuel Trim System Of Bank 1/
Min.: 0.5, Max.: 1.496

Idling: 0.5 to 1.4

O2FT B1 S1

Short Term Fuel Trim Associated With The Bank 1 Sensor 2/
Min.: -100 %, Max.: 100 %

0 +/- 20 %

Same as SHORT FT #1

O2FT B1 S2

Short term fuel trim associated with the bank 1 sensor 2/
Min.: -100 %, Max.: 100 %

0 +/- 20 %

Same as SHORT FT #2

FUEL SYS #1

Fuel System Status (Bank1) / OL or CL or OL DRIVE or OL FAULT or CL FAULT

Idling After Warming Up: CLOSED

OL: Open Loop-Has Not Yet Satisfied Conditions To Go Closed Loop.
CL: Closed Loop-Using Heated Oxygen Sensor(S) As Feed Back For Fuel Control.
OL DRIVE: Open Loop Due To Driving Conditions. (Fuel Enrichment)
OL FAULT: Open Loop Due To Detected System Fault.
CL FAULT: Closed Loop But One Of Heated Oxygen Sensors, Which Is Used For Fuel Control, Is Functioning Improperly.

FC IDL

Fuel Cut Idle/ ON or OFF

Fuel Cut Operating: ON

FC IDL = "ON" When Throttle Valve Fully Closed And Engine Speed Is Over 1,500 RPM.

MIL

MIL Status/ ON or OFF

MIL ON: ON

O2 LR B1 S1

Response Time Of The Heated Oxygen Sensor, Lean To Rich (Bank 1 Sensor 1)/
Min.: 0 ms, Max.: 16,711 ms

Idling After Warming Up:
0 to 1,000 msec.

O2 RL B1 S1

Response Time Of The Heated Oxygen Sensor, Rich To Lean (Bank 1 Sensor 1)/
Min.: 0 ms, Max.: 16,711 ms

Idling After Warming Up: 0 to 1,000 msec.

STARTER SIG

Starter Signal/ ON or OFF

Cranking: ON

A/C SIG

A/C Signal/ ON or OFF

A/C ON: ON

PNP SW [NSW]⁽²⁾

Park/Neutral Position Switch Signal/ ON Or OFF

P or N Position: ON

ELECTLOAD SIG

Electrical Load Signal / ON or OFF

Defogger Switch ON: ON

STOP LIGHT SW

STOP LIGHT SW Stop Light Switch/ ON or OFF

Brake Pedal Depressed: ON
Brake Pedal Released: OFF

PS OIL PRESS SW

Power Steering Signal/ ON or OFF

Steering Position Is;
Center: OFF
Except Center: ON

PS SIGNAL

Power Steering Signal/
ON or OFF

When The Steering Wheel Is Turned

This Signal Is Usually ON Status Until The IG Switch Is Turned OFF.

FUEL PUMP / SPD

Fuel Pump / Speed Status /
ON/H or OFF/H

Idling: ON

A/C MAG CLUTCH

A/C Magnet Clutch Status /
ON or OFF

A/C Magnet Clutch ON: ON

EVAP VSV

VSV Status For EVAP Control/
ON or OFF

VSV Operating: ON

VSV For EVAP Is Controlled By The ECM (Ground Side Duty Control)

VVT CTRL B1

VVT Control Status (Bank 1)/
ON or OFF

VVT System Operation: ON

INT AIR CTL VSV⁽²⁾

VSV Status For Intake Air Control /
ON or OFF

IGNITION

Ignition Counter/ Min.: 0, Max.: 400

0 to 400

CYL #1, #2, #3, #4

Misfire Ratio Of The Cylinder 1 To 4/
Min.: 0 %, Max.: 50 %

0 %

This Item Is Displayed In Only Idling

MISFIRE LOAD

Engine Load For First Misfire Range/
Min.: 0 g/rev, Max.: 3.98 g/rev

Misfire 0: 0 g/rev

MISFIRE RPM

Engine RPM For First Misfire Range/
Min.: 0 g/rpm, Max.: 6,375 rpm

Misfire 0: 0 rpm

FC TAU

Fuel Cut TAU: Fuel cut during very light load

Fuel cut operating: ON

The fuel cut is being performed under very light load to prevent the engine combustion from becoming incomplete.

# CODES

Number Of Memorized DTC Codes

CHECK MODE

Check Mode/ ON or OFF

Check Mode ON: ON

See CHECK MODE PROCEDURE

⁽¹⁾	If no conditions are specifically stated for "Idling", it means the shift lever is in the N or P position, the A/C switch is OFF and all accessory switches are OFF.

⁽²⁾

A/T only

ACTIVE TEST

NOTE: Performing the ACTIVE TEST using the hand-held tester or the OBD II scan tool allows the relay, VSV, actuator and so on to operate without parts removal. Performing the ACTIVE TEST as a first step of troubleshooting is one method to shorten diagnostic time.

It is possible to display the DATA LIST during the ACTIVE TEST.

Warm up the engine.
Turn the ignition switch OFF.
Connect the hand-held tester or the OBD II scan tool to the DLC3.
Turn the ignition switch ON.
Push the "ON" button of the hand-held tester or the OBD II scan tool.
Select the item "DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST".

According to the display on tester, perform the "ACTIVE TEST".

ACTIVE TEST

Hand-held Tester Display	Test Details	Diagnostic Note
INJ VOL	[Test Details] Control The Injection Volume Min.: -12.5 %, Max.: 25 % [Vehicle Condition] Engine speed: 3,000 rpm or less	All Injectors Are Tested At Once. Injection Volume Is Gradually Changed Between -12.5 And 25%.
A/F CONTROL	[Test Details] Control The Injection Volume -12.5 Or 25 % (Change The Injection Volume -12.5 % or 25 %.) [Vehicle Condition] Engine Speed: 3,000 RPM Or Less	The Following A/F CONTROL Procedure Enables The Technician To Check And Graph The Voltage Outputs Of Both The A/F Sensor And Heated Oxygen Sensor. For Displaying The Graph Indication, Enter "ACTIVE TEST/A/F CONTROL/ USER DATA", Then Select "AFS B1S1 and O2S B1S2" or "AFS B2S1 and O2S B2S2" By Pressing "YES" Button And Push "ENTER" Button Before Pressing "F4" Button.
IAC DUTY RATIO	[Test Details] Control The ISC Duty Ratio 0 to 90 % [Vehicle Condition] Engine Speed: 3,000 rpm or less Vehicle Speed: 0 mph (0 km/h) Battery Voltage: 8.5 V or more	-
CAN CTRL VSV	[Test Details] Activate The VSV For Canister Control ON or OFF	-
TANK BYPASS VSV	[Test Details] Activate The VSV For Tank Bypass ON or OFF	-
EVAP VSV (ALONE)	[Test Details] Activate The VSV For EVAP Control ON or OFF	-
A/C MAG CLUTCH	[Test Details] Control The A/C Magnet Clutch ON or OFF	-
FUEL PUMP / SPD	[Test Details] Control The Fuel Pump ON or OFF	-
VVT CTRL B1	[Test Details] Active The VVT System (Bank 1) ON or OFF	ON: Rough Idle Or Engine Stall. OFF: Normal Engine Speed.
TC/TE1	[Test Details] Connect The TC And TE1 ON or OFF	-
FC IDL PROHBT	[Test Details] Control The Idle Fuel Cut Prohibit ON or OFF	-