Data List / Active Test

READ DATA LIST

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Body / (desired system) / Data List.

According to the display on the Techstream, read the Data List.

MASTER SWITCH

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
D Door P/W Auto SW	Driver side power window auto UP/DOWN switch signal / ON or OFF	ON: Driver side power window auto UP/DOWN switch on power window regulator master switch operated OFF: Driver side power window switch on power window regulator master switch not operated	-
P Door P/W Auto SW	Front passenger side power window remote auto UP/DOWN switch signal / ON or OFF	ON: Front passenger side power window remote auto UP/DOWN switch on power window regulator master switch operated OFF: Front passenger side power window switch on power window regulator master switch not operated	-
RR Door P/W Auto SW	Rear RH power window remote auto UP/DOWN switch signal / ON or OFF	-	-
RL Door P/W Auto SW	Rear LH power window remote auto UP/DOWN switch signal / ON or OFF	-	-
P Door P/W Up SW	Front passenger side power window remote manual UP switch signal / ON or OFF	ON: Front passenger side power window remote manual UP switch on power window regulator master switch operated OFF: Front passenger side power window switch on power window regulator master switch not operated	-
RR Door P/W up switch	Rear RH power window remote manual UP switch signal / ON or OFF	-	-
RL Door P/W up switch	Rear LH power window remote manual UP switch signal / ON or OFF	-	-
P Door P/W Down SW	Front passenger side power window remote manual DOWN switch signal / ON or OFF	ON: Front passenger side power window remote manual DOWN switch on power window regulator master switch operated OFF: Front passenger side power window switch on power window regulator master switch not operated	-
RR Door P/W Down SW	Rear RH power window remote manual DOWN switch signal / ON or OFF	-	-
RL Door P/W Down SW	Rear LH power window remote manual DOWN switch signal / ON or OFF	-	-
Door Lock Switch Status	Driver side door control switch lock signal / ON or OFF	ON: Door control switch pushed to lock position OFF: Door control switch not pushed to lock position	-
Door Unlock Switch Status	Driver side door control switch unlock signal / ON or OFF	ON: Door control switch pushed to unlock position OFF: Door control switch not pushed to unlock position	-
Window Lock Switch Status	Power window LOCK switch / ON or OFF	ON: Power window lock switch LOCK position OFF: Power window lock switch UNLOCK position	-
Number of Trouble Codes	Number of trouble codes / Min.: 0, Max.: 255	Number of DTCs will be displayed	-

D-DOOR MOTOR

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
D Door P/W Auto SW	Driver side power window auto UP/DOWN switch signal / ON or OFF	ON: Driver side power window auto UP/DOWN switch operated OFF: Driver side power window switch not operated	-
D Door P/W Up SW	Driver side power window manual UP switch signal / ON or OFF	ON: Driver side power window manual UP switch operated OFF: Driver side power window switch not operated	-
D Door P/W Down SW	Driver side power window manual DOWN switch signal / ON or OFF	ON: Driver side power window manual DOWN switch operated OFF: Driver side power window switch not operated	-
Glass Position (Close - 1/4)	Jam protection operation within range of fully closed to 1/4 open window glass position / OK or CAUTION	OK: Margin sufficient during the manual up operation CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position	-
Glass Position (1/4 - 2/4)	Jam protection operation within range of 1/4 to 1/2 open window glass position / OK or CAUTION	OK: Margin sufficient during the manual up operation CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position	-
Glass Position (2/4 - 3/4)	Jam protection operation within range of 1/2 to 3/4 open window glass position / OK or CAUTION	OK: Margin sufficient during the manual up operation CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position	-
Glass Position (3/4 - Open)	Jam protection operation within range of 3/4 to fully open window glass position / OK or CAUTION	OK: Margin sufficient during the manual up operation CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position	-
Number of Trouble Codes	Number of trouble codes / Min.: 0, Max.: 255	Number of DTCs will be displayed	-

P-DOOR MOTOR

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
P Door P/W Auto SW	Front passenger side power window auto UP/DOWN switch signal / ON or OFF	ON: Front passenger side power window auto UP/DOWN switch operated OFF: Front passenger side power window regulator switch not operated	-
P Door P/W Up SW	Front passenger side power window manual UP switch signal / ON or OFF	ON: Front passenger side power window manual UP switch operated OFF: Front passenger side power window regulator switch not operated	-
P Door P/W Down SW	Front passenger side power window manual DOWN switch signal / ON or OFF	ON: Front passenger side power window manual DOWN switch operated OFF: Front passenger side power window regulator switch not operated	-
Glass Position (Close - 1/4)	Jam protection operation within range of fully closed to 1/4 open window glass position / OK or CAUTION	OK: Margin sufficient during the manual up operation CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position	-
Glass Position (1/4 - 2/4)	Jam protection operation within range of 1/4 to 1/2 open window glass position / OK or CAUTION	OK: Margin sufficient during the manual up operation CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position	-
Glass Position (2/4 - 3/4)	Jam protection operation within range of 1/2 to 3/4 open window glass position / OK or CAUTION	OK: Margin sufficient during the manual up operation CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position	-
Glass Position (3/4 - Open)	Jam protection operation within range of 3/4 to fully open window glass position / OK or CAUTION	OK: Margin sufficient during the manual up operation CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position	-
Number of Trouble Codes	Number of trouble codes / Min.: 0, Max.: 255	Number of DTCs will be displayed	-

MAIN BODY

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
Door Lock SW-Lock	Driver side door lock switch signal / ON or OFF	ON: Driver side door lock switch is turned to lock OFF: Key is in Driver side door lock key cylinder (original position)	-
Door Lock SW-Unlock	Driver side door unlock switch signal / ON or OFF	ON: Driver side door lock switch is turned to unlock OFF: Key is in Driver side door lock key cylinder (original position)	-
FR Door Courtesy	Driver side door courtesy switch signal / ON or OFF	ON: Driver door open OFF: Driver door closed	-
Communication D-Door Motor	Connection status between power window regulator motor (for driver side) and main body ECU/OK or Stop	OK: Connection Stop: No connection	-
Communication P-Door Motor	Connection status between power window regulator motor (for front passenger side) and main body ECU/OK or Stop	OK: Connection Stop: No connection	-
Communication Master SW	Connection status between master switch and main body ECU/OK or Stop	OK: Connection Stop: No connection	-

PERFORM ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Body / (desired system) / Active Test.

According to the display on the Techstream, perform the Active Test.

WARNING:

Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function does not operate.

D-DOOR MOTOR

Tester Display	Test Part	Control Range	Diagnostic Note
Power Window	Driver side power window	OFF/UP/DOWN	-

P-DOOR MOTOR

Tester Display	Test Part	Control Range	Diagnostic Note
Power Window	Front passenger side power window	OFF/UP/DOWN	-