LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Subaru >> 2007 >> Outback i, Automatic >> Repair and Diagnosis >> Engine Performance >> System >> Engine Controls (Diagnostics) (H4SO) >> Subaru Select Monitor >> Operation >> Led Operation Mode For Engine
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Led Operation Mode For Engine

  1. On the «Main Menu» display screen, select {Each System Check}.
  2. On the «System Selection Menu» display screen, select {Engine Control System}.
  3. Select the [OK] after the information of engine type has been displayed.
  4. On the «Engine Diagnosis» display screen, select the {Current Data Display/Save}.
  5. On the «Data Display» screen, select the {Data LED Display}.
  6. Using the scroll key, scroll the display screen up or down until the desired data is shown.

    A list of the support data is shown in the following table.

    ENGINE DATA DISPLAY CHART

    Contents Display Message When LED "ON" is required
    AT/MT identification signal AT Vehicle ID Signal ON or OFF Illuminate (AT model)
    Test mode signal Test Mode Terminal U check or D check D check
    D check request D-check Flag ON or OFF Software D check
    Delivery mode terminal Delivery Mode Connector ON or OFF Delivery mode
    Neutral position switch signal Neutral Position Switch ON or OFF When neutral position signal is input.
    Idle switch signal Idle Switch Signal ON or OFF When idle switch signal is input.
    Ignition switch signal Ignition Switch ON or OFF When ignition switch is turned ON.
    Power steering switch signal P/S Switch ON or OFF When power steering switch is entered.
    Air conditioning switch signal A/C Switch ON or OFF When air conditioning switch is input.
    Starter switch signal Starter Switch ON or OFF When starter switch is input.
    Rear oxygen sensor rich signal Rear O2 Rich Signal Rich or Lean When rear oxygen sensor mixture ratio is rich.
    Knocking signal Knocking Signal Provided or None When knocking signal is input.
    Crankshaft position sensor signal Crankshaft Position Signal Provided or None When crankshaft position sensor signal is input.
    Camshaft position sensor signal Camshaft Position Signal Provided or None When camshaft position sensor signal is input.
    Rear defogger switch signal Rear Defogger Switch ON or OFF When rear defogger switch is turned to ON.
    Blower fan switch signal Blower Fan Switch ON or OFF When blower fan switch is turned to ON.
    Light switch signal Light Switch ON or OFF When light switch is turned ON.
    A/C middle pressure switch signal A/C Mid Pressure Switch ON or OFF When A/C middle pressure switch is turned to ON.
    Air conditioning relay signal A/C Compressor Signal ON or OFF When air conditioning relay is in function.
    Radiator fan relay 1 signal Radiator Fan Relay #1 ON or OFF When radiator fan relay 1 is in function.
    Radiator fan relay 2 signal Radiator Fan Relay #2 ON or OFF When radiator fan relay 2 is in function.
    Fuel pump relay signal Fuel Pump Relay ON output or OFF output ON output
    PCV hose assembly diagnosis signal Blow-by Leak Connector Connected or Not connected PVC hose assembly connected
    Pressure control solenoid valve signal PCV Solenoid Valve ON or OFF Pressure control solenoid valve is operated.
    Drain valve signal Vent Control Solenoid ON or OFF Drain valve is operated.
    Variable valve lift diagnosis oil pressure switch signal 1 Oil Press. SW1 ON or OFF When variable valve lift diagnosis oil pressure switch signal 1 is ON.
    Variable valve lift diagnosis oil pressure switch signal 2 Oil Press. SW2 ON or OFF When variable valve lift diagnosis oil pressure switch signal 2 is ON.
    AT retard angle demand signal Retard Signal Provided or None When AT retard angle demand signal is input.
    AT fuel cut signal Fuel Cut Provided or None When AT fuel cut signal is input.
    AT coordinate permission signal Torque Control Permission ON or OFF When AT coordinate permission signal is input.
    Electronic throttle control motor relay signal ETC Motor Relay ON or OFF When electronic throttle control motor relay is in function.
    Clutch switch signal Clutch switch ON or OFF When clutch switch is turned to ON.
    Stop light switch signal Stop Light Switch ON or OFF When stop light switch is turned ON.
    SET/COAST switch signal SET/COAST Switch ON or OFF When SET/COAST switch is turned to ON.
    RES/ACC switch signal RESUME/ACCEL Switch ON or OFF When RES/ACC switch is turned to ON.
    Brake switch signal Brake Switch ON or OFF When brake switch is turned to ON.
    Main switch signal Main Switch ON or OFF When main switch is turned to ON.
    Data reception signal Body Int. Unit Data Provided or None Data reception signal input
    Counter update signal Body Int. Unit Count Provided or None Counter update signal input
    Cancel switch signal Cancel Switch ON or OFF When cancel switch is turned to ON.
    Malfunction indicator light signal MIL on Lit or unlit Malfunction indicator light illuminates
    NOTE: For detailed operation procedure, refer to the "SUBARU SELECT MONITOR OPERATION MANUAL".
scientia non olet · About LEMON Manuals