LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Subaru >> 2015 >> BRZ Limited, Automatic Trans >> Repair and Diagnosis >> Engine Performance >> Engine Control Systems >> Fuel Injection System >> Fuel Sender Gauge Assembly (Fa20) >> Removal
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Fuel Sender Gauge Assembly (Fa20): Removal

  1. Fuel spill prevention procedure (Refer to FUEL SYSTEM (FA20)  )
  2. Fuel draining (Refer to REMOVAL  )
  3. Disconnection of the battery ground terminal (Refer to WORKING PRECAUTIONS AND NOTES )
  4. Separate type rear seat cushion Assembly RH removal (Refer to DISASSEMBLY )
  5. Separate type rear seat cushion Assembly LH removal (Refer to DISASSEMBLY )
  6. Rear floor service hole cover No. 2 removal (Refer to REMOVAL  )
  7. Fuel pump Assembly removal (Refer to REMOVAL  )
  8. Removal of fuel sender gauge Assembly
    1. Disconnect the fuel sender gauge connector and remove the harness from the clamp.
      Fig 1: Disconnecting Fuel Sender Gauge Connector
      G08552606Courtesy of SUBARU OF AMERICA, INC.
    2. Push up the claw to remove the fuel sender gauge Assembly.
      CAUTION: Do not bend the arm of fuel sender gauge Assembly.
      Fig 2: Removing Fuel Sender Gauge Assembly
      G08552652Courtesy of SUBARU OF AMERICA, INC.
  9. Rear floor service hole cover removal
    1. Push in the grommet to remove the grommet from the rear floor service hole cover.
    2. Remove the butyl tape and remove the rear floor service hole cover.
      Fig 3: Identifying Rear Floor Service Hole Cover
      G10213538Courtesy of SUBARU OF AMERICA, INC.
    3. Disconnect the fuel sub sender gauge connector.
      Fig 4: Locating Fuel Sub Sender Gauge Connector
      G10213539Courtesy of SUBARU OF AMERICA, INC.
  10. Fuel sub sender gauge Assembly removal
    1. Use the SST to loosen the ring nut.

      SST 42099CA000

      CAUTION:
      • If the fuel gauge indicates that two thirds or more of the fuel is remaining, be sure to drain the fuel before starting the work to avoid the fuel to spill.
      • Do not use any tools other than the SST.
      • Do not turn the fuel sub sender gauge Assembly in the fuel tank Assembly to prevent the arm of fuel sender gauge Assembly No. 2 from bending.
      NOTE: Insert the cutout portion of SST into the rib of ring nut to fix the SST securely.
      Fig 5: Removing Fuel Sub Sender Gauge Assembly
      G10213540Courtesy of SUBARU OF AMERICA, INC.
    2. Take out the fuel sub sender gauge Assembly from the fuel tank and remove the filter and fuel delivery tube as a unit from the fuel sub sender gauge Assembly.
      CAUTION:
      • Do not bend the arm of fuel sender gauge Assembly No. 2.
      • Be careful not to spill the fuel outside the fuel tank or in the vehicle.
      Fig 6: Identifying Fuel Sub Sender Gauge Assembly
      G10213541Courtesy of SUBARU OF AMERICA, INC.
  11. Fuel sender gauge assembly No. 2 removal
    1. Disconnect the connector from the fuel sender gauge assembly No. 2 and remove the harness from the clamp.
      Fig 7: Locating Fuel Sender Gauge Assembly No. 2 Connector
      G10213542Courtesy of SUBARU OF AMERICA, INC.
    2. Push the claw and remove the fuel sender gauge assembly No. 2 by sliding it in the direction as shown in the figure.
      CAUTION: Do not bend the arm of fuel sender gauge Assembly No. 2.
      Fig 8: Removing Fuel Sender Gauge Assembly No. 2
      G10213543Courtesy of SUBARU OF AMERICA, INC.
scientia non olet · About LEMON Manuals