Customize Parameters

Customize Entry And Start System (For Entry Function)

NOTE: The following items can be customized.

CAUTION:

When the customer requests a change in a function, first make sure that the function can be customized.
Record the current settings before customizing.

Customize Entry And Start System (For Entry Function)

Customizing with the SSM3
Connect the SSM3 to the DLC3.
Turn the engine switch on (IG).
Turn the SSM3 on.
Enter the following menus: [Keyless access system check] →[Collation ECM] →[Unit customizing]
Select the setting by referring to the TABLE below.

Entry & Start

RELEVANT ECU ENTRY & START DESCRIPTION

Display	Default	Content	Setting	Relevant ECU
[Ignition Available Area]	All	Function that sets the area that the key must be in before the engine switch can be operated.	Front or All	Certification ECU (smart key ECU assembly)
[Parking Wait Time]	2.5s	Function that sets the period of time (lock confirmation time) that the door is prevented from being unlocked by operating the front door outside handle assembly after an entry lock operation is performed.	0.5s, 1.5s, 2.5s or 5s	Certification ECU (smart key ECU assembly)
[Trunk Open Mode]	ON	Function that opens the trunk when the driver has the electrical key transmitter sub-assembly and presses the trunk opening switch assembly.	OFF or ON	Certification ECU (smart key ECU assembly)
[Smart Cancel]	OFF	Function that enables or disables the entry and start system.	OFF or ON	Certification ECU (smart key ECU assembly)
[Smart door unlock mode]	Driver	Function that chooses the doors to be operated by entry unlock operation.	All or Driver	Certification ECU (smart key ECU assembly)
[Touch Activation Over Threshold]	Active	The function that limits the consecutive entry lock operation to only 2 times can be changed between Active and Not Active. When in Not Active mode, there is no limit for the number of times that the consecutive entry lock operation can be performed.	Active or Not Active	Certification ECU (smart key ECU assembly)

Warning

RELEVANT ECU WARNING DESCRIPTION

Display	Default	Content	Setting	Relevant ECU
[Key Low Battery Warning]	ON	Enables or disables the sounding of the buzzer when the key battery is low and the engine switch is turned off after being on (IG) for 20 minutes or more.	OFF or ON	Certification ECU (smart key ECU assembly)
[Key Left in Vehicle Buz]	ON	Function to warn when left the electrical key transmitter sub-assembly in the vehicle.	OFF or ON	Certification ECU (smart key ECU assembly)
[IG ON Key Out Warning]	ON	Enables or disables the lock sensor function that sets off the alarm if the lock sensor is touched when the shift lever is in P (transmission A/T) and the power is ON.	OFF or ON	Certification ECU (smart key ECU assembly)

Entry cancel function (manual operation)
NOTE: While the entry and start system is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the key against the engine switch.
1. The following functions are disabled when the entry and start system is canceled.
  1. Entry unlock/lock functions
  2. Entry ignition function
  3. Key lock-in prevention function
  4. Entry back door open/lock function
  5. Entry warning functions
2. Canceling the system operation:
  1. Make sure the following conditions are met:
    - The engine switch is off.
    - The driver side door is closed.
    - The driver side door is unlocked.
  2. Press the unlock switch of the electrical key transmitter sub-assembly.
  3. Open the driver side door within 5 seconds of completing the step above (driver side door: closed at beginning of step→opened).
  4. With the driver side door open, press the unlock switch of the electrical key transmitter sub-assembly 2 times within 5 seconds of completing the step above.
    CAUTION: If the driver side door is closed before or while pressing the unlock switch, the entry cancel setting mode will end.
  5. Close and open the driver side door twice within 30 seconds of completing the above step (driver side door: open at beginning of step →closed →opened →closed →opened).
  6. With the driver side door open, press the unlock switch of the electrical key transmitter sub-assembly 2 times within 30 seconds of completing the step above.
    CAUTION: If the driver side door is closed before or while pressing the unlock switch, the entry cancel setting mode will end.
  7. Close and open the driver side door within 30 seconds of completing the step above (driver side door: open at beginning of step→ closed →opened).
  8. Close the driver side door within 5 seconds of completing the above step.
  9. Check that the wireless buzzer sounds twice (short beeps) to confirm that the entry and start system has been canceled.
3. Perform the following procedure to restore the entry and start system to the active state from the canceled state.
  1. Perform the procedures to cancel the entry and start system again.
4. Check that the wireless buzzer sounds once (short beep) to confirm that the entry and start system has been restored to the active state.
  NOTE:
  - The system changes between the canceled state and the active state each time the procedure to cancel the system is performed.
  - The buzzer sounds twice when the system changes from the active state to the canceled state, and sounds once when the system changes from the canceled state to the active state.