LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Subaru >> 2024 >> Ascent Limited >> Repair and Diagnosis >> Engine Performance >> System >> Engine Control System (Diagnostics - Introduction) >> Control Module I/O Signal >> Electrical Specification
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Electrical Specification

G14614355Courtesy of SUBARU OF AMERICA, INC.
Description Connector No. Terminal No. Signal (V) Note
Ignition SW ON After warm-up (at engine OFF) Engine ON After warm-up (at idle)
Crankshaft position sensor Power supply E159 30 5 5 -
Signal E159 4 0 or 5 0 or 5 Waveforms 1 and 8
Ground E159 5 0 0 -
Intake camshaft position sensor RH E158 56 0 or 5 0 or 5 Waveform 1
LH E158 57 0 or 5 0 or 5 Waveform 1
Exhaust camshaft position sensor RH E158 24 0 or 5 0 or 5 Waveform 1
LH E158 40 0 or 5 0 or 5 Waveform 1
Camshaft position sensor ground E158 41 0 0 -
Front oxygen (A/F) sensor IP (+) signal E158 52 0 - battery voltage 2 - 4
  • Waveform 2
  • When the ignition switch is turned to ON and after engine is warmed up (engine is OFF), voltage varies depending on the sensor temperature.
VS (+) signal E158 51 0 - battery voltage 3 - 5
  • Waveform 2
  • When the ignition switch is turned to ON and after engine is warmed up (engine is OFF), voltage varies depending on the sensor temperature.
COM signal E158 53 0 - battery voltage 3 - 4 When the ignition switch is turned to ON and after engine is warmed up (engine is OFF), voltage varies depending on the sensor temperature.
Heater signal B134 32 Battery voltage 0 or battery voltage Waveform 4
Rear oxygen sensor (+) signal E158 5 2 - 3 2 - 3 Waveform 3
(-) signal E158 4 2 - 3 2 - 3 -
Heater signal E159 3 Battery voltage 0 or battery voltage Waveform 4
Air flow sensor signal B134 62 0 or 5 0 or 5 Waveform 13
Intake air temperature sensor (Integrated with air flow sensor) B134 34 2 - 3 2 - 3 -
Engine coolant temperature sensor E158 49 1 - 3 1 - 3 -
Engine oil temperature sensor E158 36 1 - 3 1 - 3 -
Manifold absolute pressure sensor E158 35 2 1 -
Intake air temperature sensor (Integrated with manifold absolute pressure sensor) E158 34 2 - 3 2 - 3 -
Fuel pressure sensor Main signal E158 22 1 - 1.6 1 -
Sub signal E158 54 3 - 3.6 3 - 3.6 -
CPC pressure sensor E158 50 1 - 4 1 - 4 -
Knock sensor RH E158 3 2.5 2.5 -
LH E158 2 2.5 2.5 -
Accelerator pedal position sensor Main power supply B134 51 5 5 -
Main signal B134 35 Fully closed: 0.4 - 1
Fully open: 2.4 - 3.7		 Fully closed: 0.4 - 1
Fully open: 2.4 - 3.7		 Waveforms 2, 3, 5 and 6
Main ground B134 19 0 0 -
Sub power supply B134 49 5 5 -
Sub signal B134 33 Fully closed: 0.4 - 1
Fully open: 2.4 - 3.7		 Fully closed: 0.4 - 1
Fully open: 2.4 - 3.7		 -
Sub ground B134 17 0 0 -
Tumble generator valve actuator RH Position signal E158 38 1 1 Fully closed: 1
Fully opened: 3
Waveform 5
Motor open E158 44 0 0 When in operation: Waveform 5
Motor closed E158 43 0 0 When in operation: Waveform 5
Tumble generator valve actuator LH Position signal E158 6 1 1 Fully closed: 1
Fully opened: 3
Waveform 6
Motor open E158 46 0 0 When in operation: Waveform 6
Motor closed E158 45 0 0 When in operation: Waveform 6
Intake oil control solenoid RH E158 14 Battery voltage 0 or battery voltage Drive frequency: 125 Hz
Waveform 7
LH E158 13 Battery voltage 0 or battery voltage Drive frequency: 125 Hz
Waveform 7
Exhaust oil control solenoid RH E158 12 Battery voltage 0 or battery voltage Drive frequency: 125 Hz
Waveform 7
LH E158 11 Battery voltage 0 or battery voltage Drive frequency: 125 Hz
Waveform 7
Purge control solenoid valve E159 19 Battery voltage Battery voltage When in operation: 0 or battery voltage
Ignition coil #1 E158 10 0 0 or 5 Waveform 8
#2 E158 26 0 0 or 5 Waveform 8
#3 E158 42 0 0 or 5 Waveform 8
#4 E158 58 0 0 or 5 Waveform 8
EGR control valve A (+) E158 62 0 or battery voltage 0 or battery voltage -
A (-) E158 60 0 or battery voltage 0 or battery voltage -
B (+) E158 61 0 or battery voltage 0 or battery voltage -
B (-) E158 59 0 or battery voltage 0 or battery voltage -
Leak check valve assembly Switching valve B134 13 Battery voltage Battery voltage Operating: 0
Vacuum pump B134 30 Battery voltage Battery voltage Operating: 0
Pressure sensor B134 2 1 - 4 1 - 4 When ignition switch is turned to ON: atmospheric pressure
Fuel pump control Control signal B134 11 ON: 0 or battery voltage
OFF: 0		 0 or battery voltage Waveform 9
Diagnostic signal B134 36 ON: Battery
voltage OFF: 0		 Battery voltage -
High-pressure fuel pump HI E159 1 - - Measurement prohibited
LO E159 9 - - Measurement prohibited
Fuel injector Power supply B134 16 Battery voltage Battery voltage -
#1 (+) E158 16 0 - Measurement is prohibited while the engine is running
#1 (-) E158 15 0 -
#2 (+) E158 32 0 -
#2 (-) E158 31 0 -
#3 (+) E158 48 0 -
#3 (-) E158 47 0 -
#4 (+) E158 64 0 -
#4 (-) E158 63 0 -
Electronic throttle control Power supply E159 22 5 5 -
Main signal E159 31 Fully closed: Approx. 0.7
Fully open: Approx. 3.9		 Fully closed: Approx. 0.7
Fully open: Approx. 3.9		 -
Sub signal E159 15 Fully closed: Approx. 4.4
Fully open: 1.1		 Fully closed: Approx. 4.4
Fully open: 1.1		 -
Ground E159 23 0 0 -
Motor (+) E158 30 0 or battery voltage 0 or battery voltage Drive frequency: 10 kHz
Motor (-) E158 29 0 or battery voltage 0 or battery voltage Drive frequency: 10 kHz
Electronic throttle control motor power supply B134 64 Battery voltage Battery voltage -
Electronic throttle control relay control B134 60 0 0 -
Electronic wastegate valve Position signal E158 37 1 - 1.4 1 - 1.4 -
Motor (+) E159 18 0 or battery voltage 0 or battery voltage -
Motor (-) E159 26 0 or battery voltage 0 or battery voltage -
Electronic air by-pass valve E158 9 Battery voltage Battery voltage -
Radiator main fan Control signal B134 59 0 or battery voltage 0 or battery voltage ON
Diagnostic signal B134 9 0 or battery voltage 0 or battery voltage -
Main fan relay control B134 46 0 0 -
Radiator sub fan Control signal B134 27 0 or battery voltage 0 or battery voltage ON
Diagnostic signal B134 41 0 or battery voltage 0 or battery voltage -
Sub fan relay control B134 45 0 0 -
Self-shutoff relay control B134 29 0 0 -
Starter relay control B134 12 Battery voltage Battery voltage Models without push button start: Waveform 10
Models with push button start: Waveform 12
Starter cut relay control B134 44 Battery voltage Battery voltage Models without push button start: Waveform 10
Models with push button start: Waveform 11 and 12
Starter switch B134 55 0 0 Models without push button start: Waveform 10
Models with push button start: Waveform 11
Starter switch 2 B134 53 0 0 Models without push button start: Waveform 10
Models with push button start: Waveform 11
Accessory cut request B134 43 Battery voltage Battery voltage Models with push button start: Waveform 11
Engine speed output B134 58 Battery voltage 0 or battery voltage Models with push button start: Waveform 12
Brake switch 1 (Brake switch) B134 8 When brake pedal is depressed: 0
When brake pedal is released: Battery voltage		 When brake pedal is depressed: 0
When brake pedal is released: Battery voltage		 -
Brake switch 2 (Stop light switch) B134 39 When brake pedal is depressed: Battery voltage
When brake pedal is released: 0		 When brake pedal is depressed: Battery voltage
When brake pedal is released: 0		 -
Neutral position switch Signal E159 12 ON: 0
OFF: Battery voltage		 ON: 0
OFF: Battery voltage		 -
Ground E159 13 0 0 -
Oil level switch E158 23 0 0 Oil level LOW: 5
Ignition switch B134 54 Battery voltage Battery voltage Models with push button start: Waveform 12
Delivery mode switch B134 37 Battery voltage Battery voltage When the fuse is installed: 0
Blow-by leak diagnosis E158 39 0 0 At the time of open circuit (fault): 5
CAN communication (P/U1 CAN) HI B134 6 - - -
LO B134 5 - - -
CAN communication ((I)_P/U2 CAN) HI B134 22 - - -
LO B134 21 - - -
LIN communication B134 20 - - -
Immobilizer communication B134 4 - - -
Control module power supply B134 15 Battery voltage Battery voltage -
B134 31 Battery voltage Battery voltage -
Backup power supply B134 14 Battery voltage Battery voltage -
Sensor power supply B134 50 5 5 -
E158 1 5 5 -
E158 17 5 5 -
Ground Sensor B134 61 0 0 -
E158 33 0 0 -
Engine 1 B134 48 0 0 -
Engine 2 B134 47 0 0 -
Engine 3 B134 63 0 0 -
Engine 4 E159 10 0 0 -
Engine 5 E159 2 0 0 -
NOTE:
  • After engine is warmed up, attach the check board for measurement.
  • Place the select lever in "P" range or "N" range.
  • Turn the A/C to OFF.
  • Turn all the accessory switches to OFF.
  • Waveforms vary depending on a measurement environment and vehicle condition.
  • Oscilloscope waveform illustrated here is an example for reference. Noise and chattering in waveform are omitted.
  1. Waveform 1
    G13202299Courtesy of SUBARU OF AMERICA, INC.
    Measured terminal Crankshaft position sensor signal (E159) No. 4 (+) - Engine ground 3 (B134) No. 63 (-):
    Intake camshaft position sensor RH (E158) No. 56 (+) - Engine ground 3 (B134) No. 63 (-):
    Intake camshaft position sensor LH (E158) No. 57 (+) - Engine ground 3 (B134) No. 63 (-):
    Exhaust camshaft position sensor RH (E158) No. 24 (+) - Engine ground 3 (B134) No. 63 (-):
    Exhaust camshaft position sensor LH (E158) No. 40 (+) - Engine ground 3 (B134) No. 63 (-):
    Measuring condition While engine idling
  2. Waveform 2
    G13866166Courtesy of SUBARU OF AMERICA, INC.
    Measured terminal Front oxygen (A/F) sensor IP (+) signal (E158) No. 52 (+) - Engine ground 3 (B134) No. 63 (-):
    Front oxygen (A/F) sensor VS (+) signal (E158) No. 51 (+) - Engine ground 3 (B134) No. 63 (-):
    Accelerator pedal position sensor main signal (B134) No. 35 (+) - Engine ground 3 (B134) No. 63 (-):
    Measuring condition (a) accelerator pedal fully closed (b) accelerator pedal half open (c) accelerator pedal fully opened
  3. Waveform 3
    G13627317Courtesy of SUBARU OF AMERICA, INC.
    Measured terminal Rear oxygen sensor (+) signal (E158) No. 5 (+) - Rear oxygen sensor (-) signal (E158) No. 4 (-):
    Accelerator pedal position sensor main signal (B134) No. 35 (+) - Engine ground 3 (B134) No. 63 (-):
    Measuring condition (a) Accelerator pedal fully closed (b) Accelerator pedal fully opened
  4. Waveform 4
    G13202302Courtesy of SUBARU OF AMERICA, INC.
    Measured terminal Front oxygen (A/F) sensor heater signal (B134) No. 32 (+) - Engine ground 3 (B134) No. 63 (-):
    Rear oxygen sensor heater signal (E159) No. 3 (+) - Engine ground 3 (B134) No. 63 (-):
    Measuring condition While engine idling
  5. Waveform 5
    G13202303Courtesy of SUBARU OF AMERICA, INC.
    Measured terminal Tumble generator valve actuator RH position signal (E158) No. 38 (+) - Engine ground 3 (B134) No. 63 (-):
    Tumble generator valve actuator RH motor open (E158) No. 44 (+) - Engine ground 3 (B134) No. 63 (-):
    Tumble generator valve actuator RH motor closed (E158) No. 43 (+) - Engine ground 3 (B134) No. 63 (-):
    Accelerator pedal position sensor main signal (B134) No. 35 (+) - Engine ground 3 (B134) No. 63 (-):
    Measuring condition (a) Accelerator pedal fully closed (b) Accelerator pedal fully opened
  6. Waveform 6
    G13202304Courtesy of SUBARU OF AMERICA, INC.
    Measured terminal Tumble generator valve actuator LH position signal (E158) No. 6 (+) - Engine ground 3 (B134) No. 63 (-):
    Tumble generator valve actuator LH motor open (E158) No. 46 (+) - Engine ground 3 (B134) No. 63 (-):
    Tumble generator valve actuator LH motor closed (E158) No. 45 (+) - Engine ground 3 (B134) No. 63 (-):
    Accelerator pedal position sensor main signal (B134) No. 35 (+) - Engine ground 3 (B134) No. 63 (-):
    Measuring condition (a) Accelerator pedal fully closed (b) Accelerator pedal fully opened
  7. Waveform 7
    G13202305Courtesy of SUBARU OF AMERICA, INC.
    Measured terminal Intake oil control solenoid RH (E158) No. 14 (+) - Engine ground 3 (B134) No. 63 (-):
    Intake oil control solenoid LH (E158) No. 13 (+) - Engine ground 3 (B134) No. 63 (-):
    Exhaust oil control solenoid RH (E158) No. 12 (+) - Engine ground 3 (B134) No. 63 (-):
    Exhaust oil control solenoid LH (E158) No. 11 (+) - Engine ground 3 (B134) No. 63 (-):
    Measuring condition While engine idling
  8. Waveform 8
    G13202306Courtesy of SUBARU OF AMERICA, INC.
    Measured terminal Crankshaft position sensor signal (E159) No. 4 (+) - Engine ground 3 (B134) No. 63 (-):
    Ignition coil #1 (E158) No. 10 (+) - Engine ground 3 (B134) No. 63 (-):
    Ignition coil #2 (E158) No. 26 (+) - Engine ground 3 (B134) No. 63 (-):
    Ignition coil #3 (E158) No. 42 (+) - Engine ground 3 (B134) No. 63 (-):
    Ignition coil #4 (E158) No. 58 (+) - Engine ground 3 (B134) No. 63 (-):
    Measuring condition While engine idling
  9. Waveform 9
    G13866173Courtesy of SUBARU OF AMERICA, INC.
    Measured terminal Fuel pump control (B134) No. 11 (+) - Engine ground 3 (B134) No. 63 (-):
    Measuring condition While engine idling
  10. Waveform 10
    G13202308Courtesy of SUBARU OF AMERICA, INC.
    Measured terminal Starter switch (B134) No. 55 (+) - Engine ground 3 (B134) No. 63 (-):
    Starter switch 2 (B134) No. 53 (+) - Engine ground 3 (B134) No. 63 (-):
    Starter cut relay control (B134) No. 44 (+) - Engine ground 3 (B134) No. 63 (-):
    Starter relay control (B134) No. 12 (+) - Engine ground 3 (B134) No. 63 (-):
    Measuring condition When engine is started
  11. Waveform 11
    G13627325Courtesy of SUBARU OF AMERICA, INC.
    Measured terminal Starter switch (B134) No. 55 (+) - Engine ground 3 (B134) No. 63 (-):
    Starter switch 2 (B134) No. 53 (+) - Engine ground 3 (B134) No. 63 (-):
    Starter cut relay control (B134) No. 44 (+) - Engine ground 3 (B134) No. 63 (-):
    Accessory cut request (B134) No. 43 (+) - Engine ground 3 (B134) No. 63 (-):
    Measuring condition When engine is started
  12. Waveform 12
    G13866176Courtesy of SUBARU OF AMERICA, INC.
    Measured terminal Starter cut relay control (B134) No. 44 (+) - Engine ground 3 (B134) No. 63 (-):
    Starter relay control (B134) No. 12 (+) - Engine ground 3 (B134) No. 63 (-):
    Engine speed output (B134) No. 58 (+) - Engine ground 3 (B134) No. 63 (-):
    Ignition switch (B134) No. 54 (+) - Engine ground 3 (B134) No. 63 (-):
    Measuring condition When engine is started
  13. Waveform 13
    G12399904Courtesy of SUBARU OF AMERICA, INC.
    Measured terminal Air flow sensor signal (B134) No. 62 (+) - Engine ground 3 (B134) No. 63 (-):
    Measuring condition While engine idling
    G16446182Courtesy of SUBARU OF AMERICA, INC.
    G16446183Courtesy of SUBARU OF AMERICA, INC.
    G16446184Courtesy of SUBARU OF AMERICA, INC.
    G16446185Courtesy of SUBARU OF AMERICA, INC.
    G16446186Courtesy of SUBARU OF AMERICA, INC.
scientia non olet · About LEMON Manuals