Common Specifications & Procedures
LEGACY & OUTBACK COMMON SPECIFICATIONS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | SPECIFICATION | ||
| Torque | See Torque Specifications in applicable text under COMPONENTS WITH TORQUE SPECIFICATIONS | ||
| Axle Shaft Nut (Front) | 162.3 Ft. Lbs. (220 N.m) | ||
| Axle Shaft Nut (Rear) | 177 Ft. Lbs. (240 N.m) | ||
| Battery | |||
| 2.5L NA | SPECIFICATION | ||
| 2.4L Turbo | SPECIFICATION | ||
| Brakes | |||
| Bleeding Sequence | AIR BLEEDING | ||
| Disc Brakes | |||
| Front | FRONT DISC BRAKE | ||
| Rear | REAR DISC BRAKE | ||
| Torque | See Torque Specifications in text under COMPONENTS WITH TORQUE SPECIFICATIONS | ||
| Charging | |||
| Generator | |||
| 2.5L NA | SPECIFICATION | ||
| 2.4L Turbo | SPECIFICATION | ||
| Torque | |||
| 2.5L NA | See Torque Specifications in text under COMPONENTS WITH TORQUE SPECIFICATIONS | ||
| 2.4L Turbo | See Torque Specifications in text under COMPONENTS WITH TORQUE SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | |||
| 2.5L NA | INSTALLATION | ||
| 2.4L Turbo | INSTALLATION | ||
| Belt Routing | |||
| 2.5L NA | INSTALLATION | ||
| 2.4L Turbo | INSTALLATION | ||
| Engine Cooling | |||
| General Service Specifications | |||
| 2.5L NA | SPECIFICATION | ||
| 2.4L Turbo | SPECIFICATION | ||
| Radiator Cap Pressure | 14-18 psi (0.95-1.25 kg/cm2 , 93 - 123 kPa) | ||
| Thermostat R & I | |||
| 2.5L NA | THERMOSTAT | ||
| 2.4L Turbo | THERMOSTAT | ||
| Water Pump R & I | |||
| 2.5L NA | WATER PUMP | ||
| 2.4L Turbo | WATER PUMP | ||
| Engine Mechanical | |||
| Compression (at 200-300 RPM) | |||
| 2.5L NA | 152-203 psi (1050-1, 400 kPa (11-14 kg/cm > 2 ) | ||
| 2.4L Turbo | 196-254 psi (1, 350-1, 750 kPa (14-18 kgf/cm2 ) | ||
| Oil Pressure | |||
| 2.5L NA | While Idling: 47 kPa (0.5 kgf/cm2 , 7 psi) or more At 3, 000 RPM: 230 kPa (2.3 kgf/cm2 , 33 psi) or more |
||
| 2.4L Turbo | While Idling: 62 kPa (0.6 kg/cm2 , 9 psi) or more At 3, 000 RPM: 350 kPa (3.6 kg/cm2 , 51 psi) or more |
||
| Overhaul | |||
| 2.5L NA | SPECIFICATION | ||
| 2.4L Turbo | SPECIFICATION | ||
| Torque | |||
| 2.5L NA | See Torque Specifications in text for appropriate items under COMPONENTS WITH TORQUE SPECIFICATIONS | ||
| 2.4L Turbo | See Torque Specifications in text for appropriate items under COMPONENTS WITH TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE. | ||
| Flywheel/Flex Plate (Drive Plate) Torque | |||
| 2.5L NA | 1st step: 22.1 Ft. Lbs. (30 N.m) 2nd step: 30°-35° |
||
| 2.4L Turbo | 1st step: 22.1 Ft. Lbs. (30 N.m) 2nd step: 30°-35° |
||
| Fuel System | |||
| Fuel Pressure Test Procedure | |||
| 2.5L NA | INSPECTION | ||
| 2.4L Turbo | INSPECTION | ||
| Fuel Filter Location | Fuel filter is attached to Fuel Pump Unit located fuel tank. | ||
| Ignition | |||
| Firing Order & Cylinder Identification | |||
| 2.5L NA | |||
| 2.4L Turbo | |||
| Ignition Wires (Resistance) | |||
| 2.5L NA | Engine is equipped with Coil-On-Plug ignition. | ||
| 2.4L Turbo | Engine is equipped with Coil-On-Plug ignition. | ||
| Ignition Wires (Routing) | Engines are equipped with Coil-On-Plug ignition. | ||
| Spark Plug | |||
| 2.5L NA | NGK: DILKAR7Q8 / Gap: 0.7 - 0.8 mm (0.028 - 0.031 in.) / Tightening Torque: 18 N.m (13.3 ft-lb) | ||
| 2.4L Turbo | NGK: SILKFR8A6 / Gap: 0.5 - 0.6 mm (0.020 - 0.024 in.) / Tightening Torque: 18 N.m (13.3 ft-lb) | ||
| Starting | |||
| Starter | |||
| 2.5L NA | SPECIFICATION | ||
| 2.4L Turbo | SPECIFICATION | ||
| Torque | 36.9 Ft. Lbs. (50 N.m) | ||
| Wheel Alignment | |||
| Adjustment Specifications | |||
| Front | WHEEL ALIGNMENT | ||
| Rear | WHEEL ALIGNMENT | ||
| Torque | |||
| Front | See Torque Specifications in text under COMPONENTS WITH TORQUE SPECIFICATIONS | ||
| Rear | See Torque Specifications in text under COMPONENTS WITH TORQUE SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 88.5 Ft. Lbs. (120 N.m) | ||