LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Suzuki >> 2006 >> Verona Base >> Repair and Diagnosis >> Engine Performance >> System >> Engine Control System - DTC P0030 Through P0175 >> DTC P0101: Mass Air Flow (MAF) Sensor Performance >> DTC Troubleshooting
April 5, 2026: LEMON Manuals is launched! Read the announcement.

DTC Troubleshooting

DTC TROUBLESHOOTING CHART

Step Action Value (s) Yes No
1 Perform an ON-BOARD DIAGNOSTIC (OBD II) SYSTEM CHECK .
Is the system check complete?		 - Go to Step 2. Go to ON-BOARD DIAGNOSTIC (OBD II) SYSTEM CHECK .
2
  1. Check for any of the following conditions:
    • Any objects blocking the MAF sensor inlet screen.
    • The intake manifold vacuum leaks.
    • The throttle body vacuum leaks.
    • Any Exhaust Gas Recirculation (EGR) valve leaks.
    • A faulty, missing, or incorrectly installed Positive Crankcase Ventilation (PCV) valve.
  2. Repair as necessary.

Was a repair necessary?		 - Go to Step 13. Go to Step 3.
3
  1. Turn the ignition ON, leaving the engine OFF.
  2. Using a scan tool, clear the DTC.
  3. Operate the vehicle within the Freeze Frame conditions as noted.

Is DTC P0101 set?		 - Go to Step 4. Go to Diagnostic Aids .
4
  1. Turn the ignition OFF.
  2. Disconnect the MAF sensor electrical connector.
  3. Turn the ignition ON, leaving the engine OFF.
  4. Probe the MAF sensor ignition feed circuit at the MAF sensor harness connector using a test lamp connected to ground.

Is the test lamp illuminated?		 - Go to Step 5. Go to Step 9.
5 Connect the test lamp between the MAF sensor ignition feed circuit and the ground circuit at the MAF sensor harness connector.
Is the test lamp illuminated?		 - Go to Step 6. Go to Step 10.
6
  1. Turn the ignition OFF.
  2. Reconnect the MAF sensor connector.
  3. Start the engine.
  4. Backprobe the MAF sensor signal circuit at the ECM using a DVM.
  5. Measure the voltage while the engine is idling.

Is the voltage within the specified range?		 0.5 - 1.0 V Go to Step 7. Go to Step 8.
7
  1. Check for a poor connection at the MAF sensor and at the ECM connectors.
  2. Repair as necessary.

Was a repair necessary?		 - Go to Step 13. Go to Step 12.
8
  1. Check the MAF sensor signal circuit for the following conditions:
    • An open between the ECM and the MAF sensor.
    • A short between the ECM and the MAF sensor.
    • A poor connection at the MAF sensor.
  2. Repair as necessary.

Was a repair necessary?		 - Go to Step 13. Go to Step 11.
9 Locate and repair the open circuit in the ignition feed circuit to the MAF sensor.
Is the repair complete?		 - Go to Step 13. -
10 Locate and repair the open circuit in the ground circuit to the MAF sensor.
Is the repair complete?		 - Go to Step 13. -
11 Replace the MAF sensor.
Is the replace complete?		 - Go to Step 13. -
12 Replace the ECM.
Is the replace complete?		 - Go to Step 13. -
13
  1. Start the engine.
  2. Operate the vehicle within the conditions for setting the DTC as specified in the supporting text.

Does the DTC run and pass?		 - Go to Step 14. Go to Step 2.
14 With a scan tool, observe the stored information.
Does the scan tool display any DTCs that you have not diagnosed?		 - Go to applicable DTC Table . System OK
scientia non olet · About LEMON Manuals