Scan Tool Data: Notes
As the data values given in SCAN TOOL DATA TABLE are standard values estimated on the basis of values obtained from the normally operating vehicles by using a scan tool, use them as reference values. Even when the vehicle is in good condition, there may be cases where the checked value does not fall within each specified data range. Therefore, judgment as abnormal should not be made by checking with these data alone.
Also, condition in SCAN TOOL DATA TABLE that can be checked by the scan tool are those detected by TCM and output from TCM as commands and there may be cases where the automatic transaxle or actuator is not operating (in the condition) as indicated by the scan tool.
SCAN TOOL DATA TABLE
| Scan tool data | Vehicle condition | Normal condition/reference values |
|---|---|---|
| Input shaft revolution | Ignition switch ON and engine stop | 0 RPM |
| At 60 km/h (37.5 mile/h) constant speed, 20% or less throttle opening and 3rd gear ("3" range) | 2300 RPM (displayed in increments of 50 rpm) | |
| Output shaft revolution | At vehicle stop | 0 RPM |
| At 60 km/h (37.5 mile/h) constant speed, 20% or less throttle opening and 3rd gear ("3" range) | 2300 RPM (displayed in increments of 50 rpm) | |
| Battery voltage | Ignition switch ON and engine stop | Battery voltage is displayed |
| ATF temperature | Ignition switch ON and engine stop | A/T fluid temperature is displayed |
| Pressure control Sol | At specified idle speed after warming up | 0% |
| Vehicle speed | - | Vehicle speed is displayed |
| Gear position | Ignition switch ON and select lever is in "P" position | P or N |
| Ignition switch ON and select lever is in "R" position | R | |
| Ignition switch ON and select lever is in "N" position | P or N | |
| Ignition switch ON and select lever is in "D" position | 1 | |
| Ignition switch ON and select lever is in "3" position | 1 | |
| Ignition switch ON and select lever is in "2" position | 1 | |
| Ignition switch ON and select lever is in "L" position | 1 | |
| Throttle position | Ignition switch ON and select pedal released | 0 - 12% |
| Ignition switch ON and select pedal depressed fully | 90 - 100% | |
| Accel actual position | Ignition switch ON and select pedal released | 0 - 12% |
| Ignition switch ON and select pedal depressed fully | 90 - 100% | |
| Engine speed | At specified idle speed after warming up | Engine revolution speed is displayed |
| Coolant temperature | Ignition switch ON and engine stop | Engine coolant temperature is displayed |
| Cruise control signal | Ignition switch ON and cruise control switch OFF | OFF |
| Ignition switch ON and cruise control switch ON | ON | |
| Transaxle range | Ignition switch ON and engine stop | Selector lever position is displayed |
| "3" position switch | Ignition switch ON and select lever to "3" or "2" range | ON |
| Ignition switch ON and select lever to other than "3" or "2" range | OFF | |
| Shift solenoid A (CMD) | At vehicle stop | OFF |
| At 60 km/h (37.5 mile/h) constant speed, 20% or less throttle opening and 3rd gear ("3" range) | ON | |
| Shift solenoid B (CMD) | At vehicle stop | ON |
| At 60 km/h (37.5 mile/h) constant speed, 20% or less throttle opening and 3rd gear ("3" range) | OFF | |
| TCC solenoid (CMD) | At vehicle stop | OFF |
| At 80 km/h (50 mile/h) constant speed, 20% or less throttle opening and 4th gear ("D" range) | ON | |
| Shift solenoid A (Mon) | At vehicle stop | OFF |
| At 60 km/h (37.5 mile/h) constant speed, 20% or less throttle opening and 3rd gear ("3" range) | ON | |
| Shift solenoid B (Mon) | At vehicle stop | ON |
| At 60 km/h (37.5 mile/h) constant speed, 20% or less throttle opening and 3rd gear ("3" range) | OFF | |
| TCC solenoid (Mon) | At vehicle stop | OFF |
| At 80 km/h (50 mile/h) constant speed, 20% or less throttle opening and 4th gear ("D" range) | ON | |
| Brake switch | Ignition switch ON and brake pedal released | OFF |
| Ignition switch ON and brake pedal depressed | ON | |
| MIL request | Ignition switch ON | OFF |