Automatic Transmission DTCS

AUTOMATIC TRANSMISSION DIAGNOSTIC TROUBLE CODE (DTC) LIST

DTC	Detecting item	Detecting condition (DTC will set when detecting:)
P0602	Control Module Programming Error	Data programming error
P0705	Transmission Range Sensor Circuit Malfunction (P R N D L Input)	Multiple signals are inputted simultaneously from transmission range sensor for 10 seconds or more.
P0707	Transmission Range Sensor Circuit Low	Transmission range sensor signal (P, R, N, D, 2, or L) is not inputted for more than 30 seconds when vehicle speed is higher than 30 km/h (19 mile/h).
P0711	Transmission Fluid Temperature Sensor "A" Circuit Range/Performance	Transmission fluid temperature is no change and less than 20°C (68°F) while vehicle is running at 40 km/h (25 mile/h) or more for 10 minutes or more.
P0712	Transmission Fluid Temperature Sensor "A" Circuit Low	Transmission fluid temperature sensor signal voltage is less than specified value for more than 5 minutes while engine is running.
P0713	Transmission Fluid Temperature Sensor "A" Circuit High	Transmission fluid temperature sensor signal voltage is higher than specified value for 12 minutes while vehicle is running.
P0717	Input Speed Sensor "A" Circuit No Signal	Pulse signals of input shaft speed sensor are not input although pulse signals of output shaft speed sensor are input while vehicle is running.
P0722	Output Speed Sensor Circuit No Signal	Pulse signals of output shaft speed sensor are not input although pulse signals of input shaft speed sensor are input while vehicle is running.
P0741	Torque Converter Clutch Circuit Performance or Stuck Off	Difference between engine speed and input shaft speed is larger than specification while TCC solenoid valve is turned ON.
P0742	Torque Converter Clutch Circuit Stuck On	Difference between engine speed and input shaft speed is smaller than specification while TCC solenoid valve is turned OFF.
P0751	Shift Solenoid "A" Performance or Stuck Off	Actual gear position is different from commanded gear position of TCM (Shift solenoid valve - A does not turn ON).
P0752	Shift Solenoid "A" Stuck On	Actual gear position is different from commanded gear position of TCM (Shift solenoid valve - A does not turn OFF).
P0756	Shift Solenoid "B" Performance or Stuck Off	Actual gear position is different from commanded gear position of TCM (Shift solenoid valve - B does not turn ON).
P0757	Shift Solenoid "B" Stuck On	Actual gear position is different from commanded gear position of TCM (Shift solenoid valve - B does not turn OFF).
P0961	Pressure Control Solenoid "A" Control Circuit Range/Performance	Difference between actual current of pressure control solenoid valve and current of pressure control solenoid valve calculated by TCM is more than specification.
P0962	Pressure Control Solenoid "A" Control Circuit Low	Value of pressure control solenoid valve output current is too low for 12.5 seconds or more.
P0963	Pressure Control Solenoid "A" Control Circuit High	Value of pressure control solenoid valve output current is too high for 12.5 seconds or more.
P0973	Shift Solenoid "A" Control Circuit Low	Difference between command signal and monitor signal of shift solenoid valve - A (shift solenoid valve - A circuit is shorted to ground).
P0974	Shift Solenoid "A" Control Circuit High	Difference between command signal and monitor signal of shift solenoid valve - A (shift solenoid valve - A circuit is open or shorted to power supply circuit).
P0976	Shift Solenoid "B" Control Circuit Low	Difference between command signal and monitor signal of shift solenoid valve - B (shift solenoid valve - B circuit is shorted to ground).
P0977	Shift Solenoid "B" Control Circuit High	Difference between command signal and monitor signal of shift solenoid valve - B (shift solenoid valve - B circuit is open or shorted to power supply circuit).
P1702	Internal Control Module Memory Check Sum Error	Data write error or check sum error.
P1723	Range Select Switch Malfunction	"3" position switch ON signal is inputted although transmission range sensor signal is inputted P, R, N or L range.
P2763	Torque Converter Clutch Pressure Control Solenoid Control Circuit High	Difference between command signal and monitor signal of TCC lock-up solenoid valve (TCC lock-up solenoid valve circuit is open or shorted to power supply circuit).
P2764	Torque Converter Clutch Pressure Control Solenoid Control Circuit Low	Difference between command signal and monitor signal of TCC lock-up solenoid valve (TCC lock-up solenoid valve circuit is shorted to ground).
U0073	Control Module Communication Bus Off	Transmission error that is inconsistent between transmission data and transmission monitor (CAN bus monitor) data is detected more than 30 times continuously.
U0100	Lost Communication With ECM / PCM "A"	Reception error of communication data for ECM is detected for longer than specified time continuously.