LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2007 >> FJ Cruiser 4WD, Part Time >> Repair and Diagnosis >> Engine Performance >> Engine Control System >> SFI System >> VC Output Circuit >> Inspection Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Inspection Procedure

  1. CHECK MIL 
    1. Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch ON.

      OK: 

      MIL lights up 

    OK: SYSTEM OK 

    NG: Go TO NEXT STEP 

  2. CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM 
    1. Connect an intelligent tester to the DLC3.
    2. Turn the ignition switch ON and turn the tester ON.
    3. Check the communication between an intelligent tester and ECM.

      Result 

      DTC RESULT DESCRIPTION

      Result Proceed to
      Communication is possible A
      Communication is not possible B

    A: GO TO  MIL CIRCUIT  

    B: Go TO NEXT STEP 

  3. CHECK MIL (THROTTLE BODY) 
    1. Disconnect the throttle body connector.
    2. Turn the ignition switch ON.
    3. Check the MIL.

      Result 

      DTC RESULT DESCRIPTION

      Result Proceed to
      MIL illuminates A
      MIL does not illuminate B
    4. Reconnect the throttle body connector.

    A: REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY  (See REMOVAL  )

    B: Go TO NEXT STEP 

  4. CHECK MIL (ACCELERATOR PEDAL) 
    1. Disconnect the accelerator pedal connector.
    2. Turn the ignition switch ON.
    3. Check the MIL.

      Result 

      DTC RESULT DESCRIPTION

      Result Proceed to
      MIL Illuminates A
      MIL does not Illuminate B
    4. Reconnect the accelerator pedal connector.

    A: REPLACE ACCELERATOR PEDAL ROD ASSEMBLY  (See ON-VEHICLE INSPECTION  )

    B: Go TO NEXT STEP 

  5. CHECK MIL (CANISTER PUMP MODULE) 
    1. Disconnect the canister pump module connector.
    2. Turn the ignition switch ON.
    3. Check the MIL.

      Result 

      DTC RESULT DESCRIPTION

      Result Proceed to
      MIL illuminates A
      MIL does not illuminate B
    4. Reconnect the canister pump module connector.

    A: REPLACE CHARCOAL CANISTER ASSEMBLY  (See REMOVAL )

    B: Go TO NEXT STEP 

  6. CHECK MIL (VVT SENSOR FOR BANK 1) 
    1. Disconnect the VVT sensor (bank 1) connector.
    2. Turn the ignition switch ON.
    3. Check the MIL

      Result 

      DTC RESULT DESCRIPTION

      Result Proceed to
      MIL Illuminates A
      MIL does not Illuminate B
    4. Reconnect the VVT sensor connector.

    A: REPLACE VVT SENSOR FOR BANK 1  (See REMOVAL  )

    B: Go TO NEXT STEP 

  7. CHECK MIL (VVT SENSOR FOR BANK 2) 
    1. Disconnect the VVT sensor (bank 2) connector.
    2. Turn the ignition switch ON.
    3. Check the MIL.

      Result 

      DTC RESULT DESCRIPTION

      Result Proceed to
      MIL Illuminates A
      MIL does not Illuminate B
    4. Reconnect the VVT sensor connector.

    A: REPLACE VVT SENSOR FOR BANK 2  (See REMOVAL  )

    B: Go TO NEXT STEP 

  8. CHECK HARNESS AND CONNECTOR (VC OUTPUT CIRCUIT) 
    1. Disconnect the throttle body connector.
    2. Disconnect the accelerator pedal connector.
    3. Disconnect the canister pump module connector.
    4. Disconnect the ECM connector.
    5. Check the resistance.

      Standard Resistance (Check for short) 

      TESTER CONNECTIONS AND SPECIFIED CONDITIONS

      Tester Connections Specified Conditions
      VC (B1-23) - Body ground 10 kΩ or higher
      VCPA (E47-26) - Body ground
      VCP2 (E47-27) - Body ground
    6. Reconnect the throttle body connector.
    7. Reconnect the accelerator pedal connector.
    8. Reconnect the canister pump module connector.
      Fig 1: Identifying ECM Connector Terminals
      G05108926Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    9. Reconnect the ECM connector.

    NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: REPLACE ECM  (See REMOVAL  )

scientia non olet · About LEMON Manuals