Rear Axle Beam: Installation

TEMPORARILY TIGHTEN REAR AXLE BEAM ASSEMBLY
1. Support the rear axle beam assembly with jack.
2. Install the rear axle beam assembly and 2 bolts, temporarily tighten the 2 nuts.
  
  Fig 1: Supporting Rear Axle Beam Assembly With Jack
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
TEMPORARILY TIGHTEN REAR SHOCK ABSORBER WITH COIL SPRING
1. Install the rear shock absorber with coil spring and rear shock absorber LH cushion retainer, temporarily tighten the nut.
2. Using the same manner described above to the other side.
  
  Fig 2: Locating Rear Shock Absorber Nut
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL REAR AXLE HUB & BEARING ASSEMBLY LH
1. Install the rear axle hub with the 4 bolts.
  Torque: 61 N*m (622 kgf*cm, 45 ft.*lbf)
INSTALL REAR AXLE HUB & BEARING ASSEMBLY RH
HINT:

Install the RH side by the same procedures as the LH side.

Fig 3: Locating Rear Axle Hub & Bearing Assembly LH Bolts
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
CONNECT REAR BRAKE TUBE NO. 4 (for Drum Type)
1. Temporarily tighten the rear brake tube No. 4 and flexible hose.
2. Connect the rear brake tube No. 4 with the clip to the rear axle beam assembly.
  
  Fig 4: Locating Rear Brake Tube No. 4
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Using SST, fully tighten the rear brake tube No. 4.
  SST 09023-00101
  
  Torque: 15.2 N*m (155 kgf*cm, 11 ft.*lbf)
CONNECT REAR BRAKE TUBE NO. 3 (for Drum Type)
SST 09023-00101

HINT:

Connect the RH side by the same procedures as the LH side.

Fig 5: Installing Rear Brake Tube No. 4
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL STABILIZER BAR REAR (See REMOVAL )
CONNECT PARKING BRAKE CABLE ASSEMBLY NO. 3
1. Connect the parking brake cable No. 3 with the bolt.
  Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf)
CONNECT PARKING BRAKE CABLE ASSEMBLY NO. 2
1. Connect the parking brake cable No. 2 with the bolt.
  Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf)
CONNECT SKID CONTROL SENSOR WIRE (w/ ABS)
1. Connect the skid control sensor wire with the bolt and clip.
  Torque: 5.0 N*m (51 kgf*cm, 44 in.*lbf)
2. Connect the skid control sensor connector.
3. Use the same manner described above to the other side.
INSTALL REAR DISC (for Disc Type)
HINT:

Use the same manner described above to the other side.
INSTALL REAR DISC BRAKE CALIPER ASSEMBLY LH (for Disc Type) (See INSTALLATION )
INSTALL REAR DISC BRAKE CALIPER ASSEMBLY RH (for Disc Type)
INSTALL REAR BRAKE DRUM SUB-ASSEMBLY (for Drum Type)
HINT:

Use the same manner described above to the other side.
STABILIZE SUSPENSION
1. Install the rear wheel and jack down the vehicle.
  Torque: 103 N*m (1,050 kgf*cm, 76 ft.*lbf)
2. Bounce the vehicle up and down several times to stabilize the suspension.
FULLY TIGHTEN REAR AXLE BEAM ASSEMBLY
1. Fully tighten the bolt.
  Torque: 85 N*m (867 kgf*cm, 63 ft.*lbf)
2. Using the same manner described above to the other side.
  
  Fig 7: Locating Rear Axle Beam Assembly Bolts And Nuts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
FULLY TIGHTEN REAR SHOCK ABSORBER WITH COIL SPRING
1. Fully tighten the nut.
  Torque: 80 N*m (816 kgf*cm, 59 ft.*lbf)
2. Using the same manner described above to the other side.
BLEED BRAKE LINE (See BRAKE FLUID )
INSPECT BRAKE FLUID (See BLEEDING )
INSPECT REAR WHEEL ALIGNMENT
HINT:

See ADJUSTMENT

Fig 8: Locating Rear Shock Absorber Nut
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
CHECK ABS SPEED SENSOR SIGNAL (w/ ABS)
1. Anti-lock Brake System: See TEST MODE PROCEDURE
2. Vehicle Stability Control System: See TEST MODE PROCEDURE