Data List / Active Test
- READ DATA LIST
HINT:
Using the intelligent tester's DATA LIST allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the DATA LIST early in troubleshooting in one way to save time.
- Connect the intelligent tester (with CAN VIM) to the DLC3.
- Turn the power switch ON (IG).
- Turn the intelligent tester on.
- Read the DATA LIST according to the display on the tester.
Skid control ECU:
SKID CONTROL ECU DIAGNOSTIC CHARTTester Display Measurement Item/Range Normal Condition Diagnostic Note YAW RATE Yaw rate sensor/ Min.: -128 deg/ s.
Max.: 128deg/sMin.: -128deg/s Max.: 128deg/s - YAW ZERO VALUE Memorized zero value / Min.: -128deg/s, Max.: 128deg/s Min.: -128deg/s
Max.: 128deg/s- STEERING ANG Steering sensor/ Min.: -1152 deg, Max.: 1150.875 deg Left turn: Increase
Right turn: Decrease- 1 SYS BRAKE 1 system brake / OPERATE or BEFORE OPERATE: During operation - REGEN CO OPRT Regenerate co operation / OPERATE or BEFORE OPERATE: During operation - AIR BLD SUPPORT Air bleed availability / SUPPORT or NOT SUP SUPPORT: During support - PKB SW Parking brake switch / ON or OFF ON: Parking brake applied
OFF: Parking brake released- STOP LIGHT SW Stop light switch / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released- TEST MODE Test mode / NORMAL or TEST NORMAL: Normal mode
TEST: During test mode- RESERVOIR SW Reservoir level warning switch / ON or OFF ON: Reservoir level Normal
OFF: Reservoir level Low- WHEEL SPD FR Wheel speed sensor (FR) reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Actual wheel speed Similar speed as indicated on speedometer WHEEL SPD FL Wheel speed sensor (FL) reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Actual wheel speed Similar speed as indicated on speedometer WHEEL SPD RR Wheel speed sensor (RR) reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Actual wheel speed Similar speed as indicated on speedometer WHEEL SPD RL Wheel speed sensor (RL) reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Actual wheel speed Similar speed as indicated on speedometer VEHICLE SPD Maximum wheel speed sensor reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Actual vehicle speed Speed indicated on speedometer IG VOLTAGE ECU power supply voltage / TOO HIGH, TOO LOW or NORMAL TOO HIGH: 9.5 V or over
NORMAL: 9.5 V TOO
LOW: Below 9.5 V- DECELERAT SENS Deceleration sensor 1 reading / Min.: -1.869 G, Max.: 1.869 G Approximately 0 +-0.13 G when vehicle is still Reading changes when vehicle is bounced DECELERAT SENS2 Deceleration sensor 2 reading / Min.: -1.869 G, Max.: 1.869 G Approximately 0 +-0.13 G when vehicle is still Reading changes when vehicle is bounced MAS CYL PRS 1 Master cylinder pressure sensor 1 reading / Min.: 0 V, Max.: 5 V When brake pedal is released: 0.3 to 0.9 V Reading increases when brake pedal is depressed MAS CYL PRS 2 Master cylinder pressure sensor 2 reading / Min.: 0 V, Max.: 5 V When brake pedal is released: 0.3 to 0.9 V Reading increases when brake pedal is depressed SLAFR CUR Current of SLAFR solenoid / Min,: 0 A, Max.: 3 A When brake pedal is released: 0 A - SLAFL CUR Current of SLAFL solenoid /Min.: 0 A, Max.: 3 A When brake pedal is released: 0 A - SLARR CUR Current of SLARR solenoid /Min.: 0 A, Max.: 3 A When brake pedal is released: 0 A - SLARL CUR Current of SLARL solenoid / Min.: 0 A, Max.: 3 A When brake pedal is released: 0 A - SLRFR CUR Current of SLRFR solenoid / Min.: 0 A, Max.: 3 A When brake pedal is released: 0 A - SLRFL CUR Current of SLRFL solenoid / Min.: 0 A, Max.: 3 A When brake pedal is released: 0 A - SLRRR CUR Current of SLRRR solenoid/ Min.: 0 A, Max.: 3 A When brake pedal is released: 0 A - SLRRL CUR Current of SLRRL solenoid / Min.: 0 A, Max.: 3 A When brake pedal is released: 0 A - PEDAL STROKE Stroke sensor / Min.: 0 V, Max.: 5 V When brake pedal is released: 0.7 to 1.3 V - PEDAL STROKE 2 Stroke sensor 2 / Min.: 0 V, Max.: 5V When brake pedal is released: 3.7 to 4.3 V - MC2 MC2 / ON or OFF ON: Operate - MC1 MC1 / ON or OFF ON: Operate - SSC SSC / ON or OFF ON: Operate - PATTERN A pattern drive is under enforcement / ON or OFF ON: Operate - MAIN RELAY 2 Main relay 2 for Electronically Controlled Brake / ON or OFF ON: Operate - MAIN RELAY 1 Main relay 1 for Electronically Controlled Brake / ON or OFF ON: Operate - ACC PRESS SENS 1 Accumulator pressure sensor 1 / Min.: 0 V, Max.: 5 V Specified value: 3.2 to 4.0 V - FR PRESS SENS Front right pressure sensor/Min.: .0 V, Max.: 5V When brake pedal is released: 0.3 to 0.9 V - FL PRESS SENS Front left pressure sensor / Min. 0 V, Max.: 5 V When brake pedal is released: 0.3 to 0.9 V - RR PRESS SENS Rear right pressure sensor/ Min.: 0 V, Max.: 5 V When brake pedal is released: 0.3 to 0.9 V - RL PRESS SENS Rear left pressure sensor/ Min. 0 V, Max.: 5V When brake pedal is released: 0.3 to 0.9 V - MOTOR RELAY 2 Motor relay 2 / ON or OFF ON: Motor relay ON - MOTOR RELAY 1 Motor relay 1 / ON or OFF ON: Motor relay ON - VSC Existence of VSC/WITH or WITHOUT WITH: WITH Enhanced VSC System - 2 FRAMES There is two or more frame for freeze frame data / YES or NO YES: There are two or more freeze frame data - REGEN TORQ FR Regenerative request torque (FR) / Min.: 0 N*m, Max.: 4080 N*m Electronically Controlled Brake is not operate: 0 N*m - REGEN TORQ FL Regenerative request torque (FL) / Min.: 0 N*m, Max.: 4080 N*m Electronically Controlled Brake is not operate: 0 N*m - REGEN TORQ RR Regenerative request torque (RR) / Min.: 0 N*m, Max.: 4080 N*m - - REGEN TORQ RL Regenerative request torque (RL) / Min.: 0 N*m, Max.: 4080 N*m - - SPD SEN FR FR speed sensor open detection / OPN-DET or NORMAL NORMAL: Normal condition - SPD SEN FL FL speed sensor open detection / OPN-DET or NORMAL NORMAL: Normal condition - SPD SEN RR RR speed sensor open detection /OPN-DET or NORMAL NORMAL: Normal condition - SPD SEN RL RL speed sensor open detection / OPN-DET or NORMAL NORMAL: Normal condition - YAW RATE SEN Yaw rate sensor open detection / OPN-DET or NORMAL NORMAL: Normal condition - DECELE SEN Deceleration sensor open detection / OPN-DET or NORMAL NORMAL: Normal condition - STEERING SEN Steering sensor open detection / OPN-DET or NORMAL NORMAL: Normal condition - M/C SEN 1 Master cylinder pressure sensor 1 open detection / OPN-DET or NORMAL NORMAL: Normal condition - M/C SEN 2 Master cylinder pressure sensor 2 open detection / OPN-DET or NORMAL NORMAL: Normal condition - STROKE SEN 1 Stroke sensor open detection / OPN-DET or NORMAL NORMAL: Normal condition - FR W/C SEN FR wheel cylinder pressure sensor open detection / OPN-DET or NORMAL NORMAL: Normal condition - FL W/C SEN FL wheel cylinder pressure sensor open detection / OPN-DET or NORMAL NORMAL: Normal condition - RR W/C SEN RR wheel cylinder pressure sensor open detection / OPN-DET or NORMAL NORMAL: Normal condition - RL W/C SEN RL wheel cylinder pressure sensor open detection / OPN-DET or NORMAL NORMAL: Normal condition - HV COM HV communication open detection / OPN-DET or NORMAL NORMAL: Normal condition - ACC SEN Accumulator pressure sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal condition- BUZZER Buzzer/ON or OFF ON: Buzzer ON
OFF: Buzzer OFF- RESERVOIR SW Reservoir level warning switch / ON or OFF ON: Reservoir level normal
OFF: Reservoir level low- SHIFT POSITION Shift position / FAIL / L / 2 / 3 / 4 / D(M)/R/P.N - - VSC/TRC OFF SW TRAC control switch / ON or OFF ON: TRAC control switch ON - STOP LIGHT SW Stop light switch/ON or OFF ON: Operate SYSTEM SYSTEM / ABS / VSC (TRAC) / BA / HAB/FAIL SAFE/PB/ NOSYS - - # IG ON # IG ON / 0 to 31 0 - STEERING ANG Steering sensor/ Min.: -1152 deg, Max.: 1150.875 deg Left turn: Increase Right turn: Decrease - YAW RATE Yaw rate sensor/ Min.: -128 deg/ s, Max.: 128 deg/s Min.: -128 deg/s
Max.: 128 deg/s- MAS CYL PRESS Master cylinder pressure / Min.: 0 V, Max.: 5 V When brake pedal is released: 0.3 to 0.9 V Reading increases when brake pedal is depressed PEDAL STROKE Stroke sensor/ Min.: 0 V, Max.: 5 V When brake pedal is released (SKS1):0.7 to 1.5V When brake pedal is released (SKS2): 3.7 to 4.3 V - THROTTLE Throttle position sensor / Min.: 0 deg, Max.: 125 deg Release accelerator pedal:
Approx. 0 deg.
Depress accelerator pedal:
Approx. 90 deg.- MAS PRESS GRADE Master pressure sensor grade / Min.: -30Mpa/s, Max.: 225 Mpa/s When brake pedal is released: 0 MPa - G (RIGHT & LEFT) Right and left G / Min.: -1.869 G, Max.: 1.869 G Approximately 0 +-0.13 G when vehicle is still - G (BACK & FORTH) Back and forth G / Min.: -1.869 G, Max.: 1.869 G Approximately 0 +-0.13 G when vehicle is still - SPD GRADE Vehicle speed grade /Min.: -1.869 G, Max.: 1.869 G Approximately 0 +-0.13 G when vehicle is still - # CODES Number of DTC recorded / Min.: 0, Max.: 255 Min.: 0, Max.: 39 -
- PERFORM ACTIVE TEST
HINT:
Performing the intelligent tester's ACTIVE TEST allows relay, VSV, actuator and other items to be operated without removing any parts. Performing the ACTIVE TEST early in troubleshooting is one way to save time.
The DATA LIST can be displayed during the ACTIVE TEST.
- Connect the intelligent tester (with CAN VIM) to the DLC3.
- Turn the power switch ON (READY).
- Perform the ACTIVE TEST according to the display on the tester.
Skid control ECU:
SKID CONTROL ECU DIAGNOSTIC CHARTTester Display Test Part Control Range Diagnostic Note ABS WARN LIGHT ABS warning light Warning light ON / OFF Observe combination meter VSC WARN LIGHT VSC warning light Warning light ON / OFF Observe combination meter SLIP INDI LIGHT SLIP indicator light Indicator light ON / OFF Observe combination meter BRAKE WARN LIGHT BRAKE warning light Warning light ON / OFF Observe combination meter VSC/BR WARN BUZ VSC / BRAKE warning buzzer Buzzer ON / OFF Buzzer can be heard ECB(1) INDI LIGHT Brake Control warning light Warning light ON / OFF Observe combination meter MAIN RELAY 1 MAIN RELAY 1 Relay ON / OFF Operation of solenoid (clicking sound) can be heard MAIN RELAY 2 MAIN RELAY 2 Relay ON / OFF Operation of solenoid (clicking sound) can be heard MC1 Master cut valve 1 activation Activation ON / OFF Operation of solenoid (clicking sound) can be heard MC2 Master cut valve 2 activation Activation ON / OFF Operation of solenoid (clicking sound) can be heard MOTOR RELAY 1 MOTOR RELAY 1 Relay ON / OFF Operation of solenoid (clicking sound) can be heard MOTOR RELAY 2 MOTOR RELAY 2 Relay ON / OFF Operation of solenoid (clicking sound) can be heard ECB(1) NVALID Electronically Controlled Brake control invalid Control invalid ON / OFF Operation of solenoid (clicking sound) can be heard ACC PATTERN Actuator air bleeding pattern activation Activation ON / OFF Operation of solenoid (clicking sound) can be heard SCC PATTERN Stroke simulator cut valve pattern activation Activation ON / OFF Operation of solenoid (clicking sound) can be heard POWER SUPPLY 1 Power supply air bleeding pattern activation 1 Activation ON / OFF Operation of solenoid (clicking sound) can be heard POWER SUPPLY 2 Power supply air bleeding pattern activation 2 Activation ON / OFF Operation of solenoid (clicking sound) can be heard RL AIR BLEEDING RL wheel air bleeding pattern activation Activation ON / OFF Operation of solenoid (clicking sound) can be heard RR AIR BLEEDING RR wheel air bleeding pattern activation Activation ON / OFF Operation of solenoid (clicking sound) can be heard ZERO DOWN Accumulator zero down activation Activation ON / OFF Operation of solenoid (clicking sound) can be heard PUMP PATTERN Pump check pattern activation Activation ON / OFF Operation of solenoid (clicking sound) can be heard DRAIN PATTERN Drain system air bleeding pattern activation Activation ON / OFF Operation of solenoid (clicking sound) can be heard (1) Electronically Controlled Brake