LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2007 >> Prius Base >> Repair and Diagnosis >> Engine Performance >> Engine Control System >> SFI System >> VC Output Circuit >> Inspection Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Inspection Procedure

  1. CHECK MIL 
    1. Check that the MIL (Malfunction Indicator Lamp) lights up when turning the power switch ON (IG).

      OK: 

      MIL lights up. 

    OK: SYSTEM IS OK 

    NG: Go to next step 

  2. CHECK CONNECTION BETWEEN INTELLIGENT TESTER AND ECM 
    1. Connect the intelligent tester to the DLC3.
    2. Turn the power switch ON (IG) and turn the intelligent tester ON.
    3. Check the connection between the intelligent tester and ECM.

      Result 

      RESULT REFERENCE

      Condition Proceed to
      Communication Is possible A
      Communication is not possible B

    A: Go to MIL CIRCUIT 

    B: Go to next step 

  3. CHECK ECM (VC VOLTAGE) 
    1. Turn the power switch ON (IG).
    2. Measure the voltage according to the value(s) in the table below.

      Standard voltage 

      TESTER CONNECTION SPECIFIED CONDITION

      Tester Connection Specified Condition
      E4-18 (VC) - E5-28 (E1) Voltage Is not 5 V
      Fig 1: Identifying ECM Connector Terminal E4 And E5
      G05188971Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. CHECK MIL (THROTTLE POSITION SENSOR) 
    1. Disconnect the T3 throttle body connector.
    2. Turn the power switch ON (IG).
    3. Check the MIL.

      Result 

      RESULT REFERENCE

      Condition Proceed to
      MIL illuminates A
      MIL does not illuminate B

    A: REPLACE THROTTLE BODY 

    B: Go to next step 

  5. CHECK MIL (WATER VALVE) 
    1. Disconnect the W5 water valve connector.
    2. Turn the power switch ON (IG).
    3. Check the MIL.

      Result 

      RESULT REFERENCE

      Condition Proceed to
      MIL illuminates A
      MIL does not illuminate B

    A: REPLACE WATER VALVE 

    B: Go to next step 

  6. CHECK MIL (CANISTER PUMP MODULE) 
    1. Disconnect the V7 canister pump module connector.
    2. Turn the power switch ON (IG).
    3. Check the MIL.

      Result 

      RESULT REFERENCE

      Condition Proceed to
      MIL illuminates A
      MIL does not illuminate B

    A: REPLACE CHARCOAL CANISTER ASSEMBLY 

    B: Go to next step 

  7. CHECK MIL (VAPOR PRESSURE SENSOR) 
    1. Disconnect the V6 vapor pressure sensor connector.
    2. Turn the power switch ON (IG).
    3. Check the MIL.

      Result 

      RESULT REFERENCE

      Condition Proceed to
      MIL illuminates A
      MIL does not illuminate B

    A: REPLACE VAPOR PRESSURE SENSOR 

    B: Go to next step 

  8. CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND) 
    1. Disconnect the T3 throttle body connector.
    2. Disconnect the W5 water valve connector.
    3. Disconnect the V7 canister pump module connector.
    4. Disconnect the V6 vapor pressure sensor connector.
    5. Disconnect the E4 ECM connector.
    6. Measure the resistance according to the value(s) in the table below.

      Standard resistance 

      TESTER CONNECTION SPECIFIED CONDITION

      Tester Connection Specified Condition
      E4-18 (VC) - Body ground 10 kΩ or higher

    NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Fig 2: Identifying E4 ECM Connector Terminal
    G05188972Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    OK: REPLACE ECM 

scientia non olet · About LEMON Manuals