LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2008 >> Land Cruiser >> Repair and Diagnosis >> Body & Frame >> Windows >> Window/Glass >> Power Window Control System >> Data List/Active Test
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Data List/Active Test

  1. READ DATA LIST 

    HINT:

    Using the Techstream to read the Data List allows values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    NOTE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical/(desired system)/Data List.
    5. According to the display on the Techstream, read the Data List.

      Master Switch 

      MASTER SWITCH NORMAL CONDITION CHART

      Tester Display Measurement Item/Range Normal Condition
      D Door P/W Auto SW Driver side power window auto up/down signal/ON or OFF ON: While operating driver side power window auto up/down switch on multiplex network master switch
      OFF: While not operating driver side power window switch on multiplex network master switch
      P Door P/W Auto SW Front passenger side power window remote auto up/down signal/ON or OFF ON: While operating front passenger side power window remote auto up/down switch on multiplex network master switch
      OFF: While not operating power window regulator switch on multiplex network master switch
      RR Door P/W Auto SW Rear power window RH remote auto up/down signal/ON or OFF ON: While operating rear power window RH remote auto up/down switch on multiplex network master switch
      OFF: While not operating rear power window switch RH on multiplex network master switch
      RL Door P/W Auto SW Rear power window LH remote auto up/down signal/ON or OFF ON: While operating rear power window LH remote auto up/down switch on multiplex network master switch
      OFF: While not operating rear power window switch LH on multiplex network master switch
      P Door P/W Up SW Front passenger side power window remote manual up signal/ON or OFF ON: While operating front passenger side power window remote manual up switch on multiplex network master switch
      OFF: While not operating power window regulator switch on multiplex network master switch
      RR Door P/W up switch Rear power window RH remote manual up signal/ON or OFF ON: While operating rear power window RH remote manual up switch on multiplex network master switch
      OFF: While not operating rear power window switch RH on multiplex network master switch
      RL Door P/W up switch Rear power window LH remote manual up signal/ON or OFF ON: While operating rear power window LH remote manual up switch on multiplex network master switch
      OFF: While-operating not rear power window switch LH on multiplex network master switch
      P Door P/W Down SW Front passenger side power window remote manual down signal/ON or OFF ON: While operating front passenger side power window remote manual down switch on multiplex network master switch
      OFF: While not operating power window regulator switch on multiplex network master switch
      RR Door P/W Down SW Rear power window RH remote manual down signal/ON or OFF ON: While operating rear power window RH remote manual down switch on multiplex network master switch
      OFF: While operating rear power window switch RH on multiplex network master switch
      RL Door P/W Down SW Rear power window LH remote manual down signal/ON or OFF ON: While operating rear power window LH remote manual down switch on multiplex network master switch
      OFF: While not operating rear power window switch LH on multiplex network master switch
      Window Lock Switch Status Power window lock switch/ON or OFF ON: Power window lock switch on OFF: Power window lock switch off
      Number of Trouble Codes Number of trouble codes/Min.: 0, Max.: 255 Number of DTCs will be displayed

      D-Door Motor 

      D-DOOR MOTOR NORMAL CONDITION CHART

      Tester Display Measurement Item/Range Normal Condition
      D Door P/W Auto SW Driver side power window auto up/down signal/ON or OFF ON: While operating driver side power window auto up/down switch
      OFF: While not operating driver side power window switch
      D Door PAW Up SW Driver side power window manual up signal/ON or OFF ON: While operating driver side power window manual up switch
      OFF: While not operating driver side power window switch
      D Door P/W Down SW Driver side power window manual down signal/ON or OFF ON: While operating driver side power window manual down switch
      OFF: While not operating driver side power window switch
      Glass Position (Close-1/4) Jam protection status of window glass within range of fully closed to 1/4 open position/OK or Caution OK: Motor normally operates between fully closed to 1/4 open position
      CAUTION: Jam protection function operates due to detection of foreign object or irregular movement
      Glass Position (1/4-2/4) Jam protection status of window glass within range of 1/4 to 1/2 open position/OK or Caution OK: Motor normally operates between 1/4 to 1/2 open position
      CAUTION: Jam protection function operates due to detection of foreign object or irregular movement
      Glass Position (2/4-3/4) Jam protection status of window glass within range of 1/2 to 3/4 open position/OK or Caution OK: Motor normally operates between 1/2 to 3/4 open position
      CAUTION: Jam protection function operates due to detection of foreign object or irregular movement
      Glass Position (3/4-Open) Jam protection status of window glass within range of 3/4 to fully open position/OK or Caution OK: Motor normally operates between 3/4 to fully open position
      CAUTION: Jam protection function operates due to detection of foreign object or irregular movement
      Number of Trouble Codes Number of trouble codes/Min.: 0, Max.: 255 Number of DTCs will displayed

      P-Door Motor 

      P-DOOR MOTOR NORMAL CONDITION CHART

      Tester Display Measurement Item/Range Normal Condition
      P Door P/W Auto SW Front passenger side power window auto up/down signal/ON or OFF ON: While operating front passenger side power window auto up/down switch
      OFF: While not operating power window regulator switch
      P Door P/W Up SW Front passenger side power window manual up signal/ON or OFF ON: While operating front passenger side power window manual up switch
      OFF: While not operating power window regulator switch
      P Door P/W Down SW Front passenger side power window manual down signal/ON or OFF ON: While operating front passenger side power window manual down switch
      OFF: While not operating power window regulator switch
      Glass Position (Close-1/4) Jam protection status of window glass within range of fully closed to 1/4 open position/OK or Caution OK: Motor normally operates between fully closed to 1/4 open position
      CAUTION: Jam protection function operates due to detection of foreign object or irregular movement
      Glass Position (1/4-2/4) Jam protection status of window glass within range of 1/4 to 1/2 open position/OK or Caution OK: Motor normally operates between 1/4 to 1/2 open position
      CAUTION: Jam protection function operates due to detection of foreign object or irregular movement
      Glass Position (2/4-3/4) Jam protection status of window glass within range of 1/2 to 3/4 open position/OK or Caution OK: Motor normally operates between 1/2 to 3/4 open position
      CAUTION: Jam protection function operates due to detection of foreign object or irregular movement
      Glass Position (3/4-Open) Jam protection status of window glass within range of 3/4 to fully open position/OK or Caution OK: Motor normally operates between 3/4 to fully open position
      CAUTION: Jam protection function operates due to detection of foreign object or irregular movement
      Number of Trouble Codes Number of trouble codes/Min.: 0, Max.: 255 Number of DTCs will be displayed

      RL-Door Motor 

      RL-DOOR MOTOR NORMAL CONDITION CHART

      Tester Display Measurement Item/Range Normal Condition
      RL Door P/W Auto SW Rear power window LH auto up/down signal/ON or OFF ON: While operating rear power window LH auto up/down switch
      OFF: While not operating rear power window LH switch
      RL Door P/W Up SW Rear power window LH manual up signal/ON or OFF ON: While operating rear power window LH manual up switch
      OFF: While not operating rear power window LH switch
      RL Door P/W Down SW Rear power window LH manual down signal/ON or OFF ON: While operating rear power window LH manual down switch
      OFF: While not operating rear power window LH switch
      Glass Position (Close-1/4) Jam protection status of window glass within range of fully closed to 1/4 open position/OK or Caution OK: Motor normally operates between fully closed to 1/4 open position
      CAUTION: Jam protection function operates due to detection of foreign object or irregular movement
      Glass Position (1/4-2/4) Jam protection status of window glass within range of 1/4 to 1/2 open position/OK or Caution OK: Motor normally operates between 1/4 to 1/2 open position
      CAUTION: Jam protection function operates due to detection of foreign object or irregular movement
      Glass Position (2/4-3/4) Jam protection status of window glass within range of 1/2 to 3/4 open position/OK or Caution OK: Motor normally operates between 1/2 to 3/4 open position
      CAUTION: Jam protection function operates due to detection of foreign object or irregular movement
      Glass Position (3/4-Open) Jam protection status of window glass within range of 3/4 to fully open position/OK or Caution OK: Motor normally operates between 3/4 to fully open position
      CAUTION: Jam protection function operates due to detection of foreign object or irregular movement
      Number of Trouble Codes Number of trouble codes/Min.: 0, Max.: 255 Number of DTCs will be displayed

      RR-Door Motor 

      RR-DOOR MOTOR NORMAL CONDITION CHART

      Tester Display Measurement Item/Range Normal Condition
      RR Door P/W Auto SW Rear power window RH auto up/down signal/ON or OFF ON: While operating rear power window RH auto up/down switch
      OFF: While not operating rear power window RH switch
      RR Door P/W Up SW Rear power window RH manual up signal/ON or OFF ON: While operating rear power window RH manual up switch
      OFF: While not operating rear power window RH switch
      RR Door P/W Down SW Rear power window RH manual down signal/ON or OFF ON: While operating rear power window RH manual down switch
      OFF: While not operating rear power window RH switch
      Glass Position (Close-1/4) Jam protection status of window glass within range of fully closed to 1/4 open position/OK or Caution OK: Motor normally operates between fully closed to 1/4 open position
      CAUTION: Jam protection function operates due to detection of foreign object or irregular movement
      Glass Position (1/4-2/4) Jam protection status of window glass within range of 1/4 to 1/2 open position/OK or Caution OK: Motor normally operates between 1/4 to 1/2 open position
      CAUTION: Jam protection function operates due to detection of foreign object or irregular movement
      Glass Position (2/4-3/4) Jam protection status of window glass within range of 1/2 to 3/4 open position/OK or Caution OK: Motor normally operates between 1/2 to 3/4 open position
      CAUTION: Jam protection function operates due to detection of foreign object or irregular movement
      Glass Position (3/4-Open) Jam protection status of window glass within range of 3/4 to fully open position/OK or Caution OK: Motor normally operates between 3/4 to fully open position
      CAUTION: Jam protection function operates due to detection of foreign object or irregular movement
      Number of Trouble Codes Number of trouble codes/Min.: 0, Max.: 255 Number of DTCs will be displayed

      Main Body 

      MAIN BODY NORMAL CONDITION CHART

      Tester Display Measurement Item/Range Normal Condition
      IG SW Engine switch on (IG)/ON or OFF ON: Engine switch on (IG)
      OFF: Engine switch off
      ACC SW Engine switch on (ACC)/ON or OFF ON: Engine switch on (ACC)
      OFF: Engine switch off
      Communication D-Door Motor Connection status between power window regulator motor (for driver side) and main body ECU/OK or Stop OK: Connection
      Stop: No connection
      Communication P-Door Motor Connection status between power window regulator motor (for front passenger side) and main body ECU/OK or Stop OK: Connection
      Stop: No connection
      Communication RR-Door Motor Connection status between rear power window regulator motor LH and main body ECU/OK or Stop OK: Connection
      Stop: No connection
      Communication RL-Door Motor Connection status between rear power window regulator motor RH and main body ECU/OK or Stop OK: Connection
      Stop: No connection
      Communication Master SW Connection status between master switch and main body ECU/OK or Stop OK: Connection
      Stop: No connection
      D Door Courtesy SW Driver side door courtesy signal/ON or OFF ON: Driver door open
      OFF: Driver door closed
      P Door Courtesy SW Front passenger side door courtesy signal/ON or OFF ON: Front passenger door open
      OFF: Front passenger door closed
      RL Door Courtesy SW Rear LH side door courtesy signal/ON or OFF ON: Rear LH side door open
      OFF: Rear LH side door closed
      RR Door Courtesy SW Rear RH side door courtesy signal/ON or OFF ON: Rear RH side door open
      OFF: Rear RH side door closed
  2. PERFORM ACTIVE TEST 

    HINT:

    Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical/(desired system)/Active Test.
    5. According to the display on the Techstream, perform the Active Test.
      CAUTION: Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function does not operate.

      D-Door Motor 

      D-DOOR MOTOR CONTROL RANGE REFERENCE

      Tester Display Test Part Control Range
      Power Window Driver side power window OFF/UP/DOWN

      P-Door Motor 

      P-DOOR MOTOR CONTROL RANGE REFERENCE

      Tester Display Test Part Control Range
      Power Window Front passenger side power window OFF/UP/DOWN

      RL-Door Motor 

      RL-DOOR MOTOR CONTROL RANGE REFERENCE

      Tester Display Test Part Control Range
      Power Window Rear LH side power window OFF/UP/DOWN

      RR-Door Motor 

      RR-DOOR MOTOR CONTROL RANGE REFERENCE

      Tester Display Test Part Control Range
      Power Window Rear RH side power window OFF/UP/DOWN
scientia non olet · About LEMON Manuals